netradyne DCM-NA1-200 DriverI/DCM LTE Connectivity Module User Manual
- June 6, 2024
- netradyne
Table of Contents
drivers/DCM-NA1-200
Manual
Rev: 1.0
11th Feb 2022
drivers/DCM LTE Connectivity Module (FCC ID: 2AM8R-DCM-NA1-200)
Company Name: Netradyne Inc.
Contact:
San Diego Office:
9191 Towne Centre Drive
Suite 200
San Diego, CA 92122
Call Us: 1-833-476-9663
Email: driveri@netradyne.com
Web Page: https://www.netradyne.com/contact/
Rev. A0-10
Introduction
This document is designed to provide information about DriverI/DCM for customer use.
drivers/DCM Module is an LTE Dongle designed for the US region will be used to provide high precision navigation and LTE Connectivity using T-Mobile Carrier.
drivers/DCM Device contains FCC ID – 2AM8R-DCM-NA1-200
For external host interface “DriverI/DCM Module” supports USB interface with
12V DC supply input.
DriverI/DCM Module dimensions are 66.5mm x 66.5mmx21.2mm
DriverI/DCM Module Dimensions
Figure 1: DriverI/DCM Module Dimensions
LTE Module (WP7611 – Sierra Wireless):
WP7611 is an LTE embedded wireless module. This LTE Cat-3 embedded module
delivers up to 100 Mbps download speed and is ideal for IoT applications
requiring broadband connectivity such as industrial gateways, transportation,
and mission-critical networking applications.
Offering an application processor running the open-source Legato® platform,
optional GNSS receiver, and cellular modem with an ultra-low-power domain, WP
modules reduce system complexity and get you to market faster.
The WP7611 module is based on the MDM9615 QUALCOMM baseband processors.
WP7611 LTE module used in DriverI/DCM Module of SKU – 1104278.
The following bands/connectivity are supported by the WP7611 LTE Module:
- LTE Bands: Band 2, 4, 12, 66, 71
NO MOUNT
GPS Module:
Driver/DCM device includes GPS module that delivers high integrity, precision timing in demanding applications worldwide. Support for BeiDou, GLONASS, and Galileo constellations enables compliance with national requirements. Enhanced sensitivity and concurrent constellation reception extend coverage and integrity to challenging signal environments. Survey-in and fixed-position navigation reduce timing jitter, even at low signal levels, and enable synchronization to be maintained with as few as one single satellite in view.
Inbuilt GPS module includes Flash memory for field upgrade. UART, SPI, and DDC (I2C compatible) interfaces provide connectivity and enable synergies with most u-Blox cellular modules.
Driver/DCM device GPS module use GNSS chips qualified according to AEC-Q100,
are manufactured in ISO/TS 16949 certified sites, and are fully tested on a
system level.
Qualification tests are performed as stipulated in the ISO16750 standard:
“Road vehicles –Environmental conditions and testing for electrical and
electronic equipment”.
FCC Statement
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The distance between user and products should be no less than 20cm
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End-user must follow the specific operating
instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The distance between user and products should be no less than 20cm
Rev. A0-10
Documents / Resources
|
netradyne DCM-NA1-200 DriverI/DCM LTE Connectivity
Module
[pdf] User Manual
DCM-NA1-200, DCMNA1200, 2AM8R-DCM-NA1-200, 2AM8RDCMNA1200, DCM-NA1-200 DriverI
LTE Connectivity Module, DCM-NA1-200DCM LTE Connectivity Module
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>