Shenzhen Lanyao Technology B08CMX3KY6 Sleeping Headphone Instruction Manual
- June 6, 2024
- Shenzhen Lanyao Technology
Table of Contents
Lanao Technology B08CMX3KY6 Sleeping Headphone
Instruction Manual
PACKING LISTING
- Sleep Headphones*1
- Instruction menu*1
- USB charging cable*1
- Portable Travel Bag*1
PRODUCT SPECIFICATION
Charging time 2-2.5 hours ( please charge it before using )
BT continuous working time: More Than 8 Hours
Power/Handfree/Stop/Play
Vol Up/Next
Vol Down/Previous
How To Connect BT
Close all your BT on the phone.
Long press the “on/off” button to read/blue light flash.
Open your BT on the phone, find the BT name “BT-FAAH” then connect.
You can listen to the music directly after connecting to the BT.
Only connect BT in one device at one time, please make sure to disconnect with
the previous BT device when connecting a new device
BT MUSIC PLAY INSTRUCTION
Press one PLAY/STOP button start playing, press once again to stop playing
Press Vol- button for the previous song, Press Vol- button for the previous
song.
Long press Vol- will constantly reduce the volume to a minimum and di di’sound
will be heard when reaching minimum level; Long press Vol+ will constantly
increase volume to max, a‘di di di’sound will be heard when reaches max level
BT HANDFREE
Incoming call, press one PLAY/STOP button for auto receive call.
Incoming call, press and hold the PLAY/STOP button for 3 sec to reject the
call
During the call, long press PLAY/STOP button for 3 sec will switch back to the
earphone
CHARGING FUNCTION
OPERATION INSTRUCTION
Connect the data cable to USB charger ( or computer USB port), the other end connects to our device as shown on the right diagram, our device have a LED indication on the right, RED light constant shows that the device is charging, RED light off and then became blue when charged fully ( Note: hidden charging port in inner of sleep mask on the side )
WASHABLE SLEEP MASK
A music sleep mask can be washable ( hidden wires can be taken out from the
sleep mask)
Washing the mask with warm water by hand will be recommended
NOTES:
Switch on the BT in your phone and match with BT name “BT-FAAH”.
The asleep masks can be washable when taking out the BT module.
Both speakers are not fixed, can adjust placement accordingly based on your
size.
Please check USB cable work well, if it doesn’t work for charging Please
adjust the volume from your mobile or long-press Vol+ from sleep headphones if
you can’t hear any music.
The sound may have a bit of noise if there’s environmental interference Please
contact us directly via order id, If you have any problem when using our
product, we promise to solve the problem 100%. Your user experience and
suggestions will be great to improve it better. Your Opinions Matters and
Means the Whole World To Us.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.