COMARK Diligence 600 RF612 WiFi Temperature Transmitter User Guide

Also Included:

Mounting Bracket
Use the supplied mounting bracket to secure the Transmitter to a suitable surface using appropriate fixings (not supplied).
Cable Ties
Use these to tidy and secure any cables post-installation and prevent cables from pulling out of their sockets.

Action Button
The Action Button allows you to navigate between Active Channels.

1. Press and hold for one second. The Activity (Green) LED will flash once to acknowledge the button press and you will hear a beep. The Transmitter will attempt to connect to the Diligence Cloud and send any unsent data and/or receive any new tasks. During this time the lower segment of the WiFi Signal Icon will flash.
2. Press and hold for five seconds. The Transmitter will go into Survey Mode and check the WiFi Signal Strength. To exit press the WiFi Button again.
3. Press and hold the WiFi Button and Action Button simultaneously for five seconds to place the Transmitter into Setup Mode. Press the WiFi Button again to exit Setup Mode.

Action Button
The Action Button allows you to navigate between Active Channels.

1. Press once to change the Active Channel that is displayed.
2. Press and hold the Action Button and WiFi Button simultaneously for five seconds to place the Transmitter into Setup Mode.

Alarm (Red) LED
The Alarm (Red) LED will flash whenever one or more channels is in an active (unacknowledged) alarm state. It will not flash for High and Low Alarm states but will flash for High-High and Low-Low Alarm states.
Activity (Green) LED
The Activity (Green) LED will flash briefly every second to indicate that the Transmitter is operating normally. The Activity (Green) LED will also flash once whenever the WiFi Button has been operated.
Infrared LEDs
The Infrared LEDs are only used during the manufacturing process and do not display or have any significance in normal operation.
Power and Diagnostic LEDs
These illuminate at various times depending on Transmitter interactions. Please refer to the operating manual for a full explanation of these LEDs.
Adding new Transmitters to your Diligence Cloud Account
IMPORTANT: You will need Wi-Fi enabled devices such as a Laptop or PC, and you will need to have registered for a Diligence Cloud account PRIOR TO STARTING
Adding new Transmitters to your Diligence Cloud Account
IMPORTANT: You will need a Wi-Fi enabled devices such as a Laptop or PC, and you will need to have registered for a Diligence Cloud account PRIOR TO STARTING

1. Using a Wi-Fi Device, log onto your Diligence Cloud Account, and in the bottom right-hand corner of the Dashboard page use the Copy Icon to save your Account Number to your clipboard.

2. Select Transmitter Management, click on the icon, enter the serial number of the Transmitter. Serial numbers are case-sensitive. Repeat this process for all the Transmitters you want to add.

3. On the Transmitter press the Action Button for one second and allow the Transmitter to boot up. At this stage ignore any on-screen messages.

4. Enter SETUP mode by pressing the Wi-Fi Button and the Action Button simultaneously for five seconds. The LCD will show AP. followed by AP. 0 a few seconds later.

5. On your Laptop/PC, search for available Wi-Fi networks; the Transmitter will advertise itself as RF600-. Connect to this Wi-Fi network, the password is the serial number excluding the first two digits and is case sensitive. AP. 1

6. The LCD will show

7. On your Laptop/PC, open an Internet Browser and navigate to http://192.168.4.1/setup

8. Select the Wi-Fi tab and paste in the Cloud Account Number you copied earlier.
   RF600   CA11215067
   Note – There is a timeout to conserve a battery of 4 mins.

9. Click on the Scan for WiFi button to search for Local Wi-Fi (Wireless)
   Networks. You may see multiple entries for the same Wi-Fi network, especially if your network has multiple base stations.
   Note – At the time of writing Diligence 600 only supports WPA2-PSK Wireless Networks. Enterprise Networks are not currently supported.
   Select your Wi-Fi (Wireless) Network from the drop-down and enter the Wi-Fi Password. Click Save and the page will return Save OK.

10. Click on the Server tab and confirm the Diligence Cloud tick box has been selected in the Server section, if not select it and click Save.

11. Press the Wi-Fi Button on the Transmitter to exit Setup Mode. The LCD display of your Transmitter will change to show tAS to indicate it is now configured correctly and awaiting tasks.

12. Provoke the Transmitter by pressing the Wi-Fi Button for one second. The Wi-Fi Symbol will flash as the Transmitter attempts to connect to the Diligence Cloud. If all is well, then the Wi-Fi symbol will go solid. This may take a few seconds to connect.

13. In the event of setup not working the Fault icon will be displayed with a fault code number. If the Diligence Cloud does not recognize the Transmitter then IdEr will be displayed.
    Please repeat the process from Step 4 checking your Wi-Fi details and Diligence Cloud Account Number were correct. If you continue to get error messages then contact Comark Technical Support for help.
    For additional help and information please refer to the Diligence 600 User Manual or the Help Section on the Diligence Cloud by clicking on the icon from any page.

14. Now the Transmitter needs to be set up correctly in your Diligence Cloud account; each Transmitter needs to be assigned a Location and Alarm Group.
    Log back into your Diligence Cloud account and select the icon and then Locations. Click on the icon and enter the name of the first location.
    Now select the icon again and then Alarm Groups. Click on the icon and enter the name of the first Alarm Group.
    Navigate to the Transmitter Management tab and select the icon to bring up the Task Configuration page for the selected Transmitter.
    Complete the form, select Program Task. Press and hold the Wi-Fi Button until the Transmitter beeps. It will wake up, connect to your Diligence Cloud account and receive the task.

15. Repeat this process, from Step 4, for all of your new Transmitters. Visit www.comarkinstruments.com for more info on Diligence 600.

WiFi Signal Icon
If the WiFi signal icon is not showing the Transmitter has no signal or has not been set up.
WiFi signal strength is denoted by the number of bands showing – one band is a low signal, all four bands is an excellent signal.
When the WiFi is connecting the WiFi Signal icon will flash each segment consecutively, from low to full.
Fault Alert Icon
When present the Fault Alert icon indicates that there is a fault with the Transmitter. The Fault Alert icon will usually appear with a reference number on the main LCD. Please refer to the manual for more information on the fault.
Low Battery Indicator Icon
The Low Battery Indicator icon will show when the battery is low. The Transmitter will continue to operate normally, but we recommend replacing the batteries with new as soon as possible.
If the Low Battery Indicator icon is flashing then the battery is critically low and should be replaced immediately.
Alarm Active Icon
The Alarm Active icon will flash when the Active Channel is registering an unacknowledged alarm.
H High/Low Alarm Icons
L The High/Low Alarm icon will show to alert you that the value displayed in the Active Channel exceeds the alarm limit. If the High/Low Alarm icon is flashing then the Active Channel is registering a High/Low Alarm.
Action Icons
The Play icon will flash when the Transmitter is tasked and logging normally. This is normal status. If solid, the Transmitter has received a task but waiting for a reading.
The Pause icon indicates that the Transmitter is not logging.
The Action icon indicates that the Transmitter is waiting for input from the user to perform an action.

References

• Comark Instruments - The Professional's Choice for Temperature Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>