FOXTECH MX16 Al-in-one Portable Ground Control Station User Manual

: June 6, 2024
: FOXTECH

Table of Contents

Introduction
Preparation and Checking Before Use
- Preparation and Checking Before Use
- Usage
FAQ
Documents / Resources

MX16/MX16 Pro
All-in-one Portable Ground Control Station
FOXTECH MX16 Al in one Portable Ground Control Station User Manual
V 3.2
202104

Introduction

Product Characteristics

MX16 series adopts a new processor, equipped with an Android embedded system, adopts advanced SDR technology, and a super protocol stack to ensure clearer image, lower latency, longer distance, and high anti-interference performance, it can be used to control drones, Robots, and other industrial equipment, etc.
Support HDMI, Rj45, sensor port, dual serial port pass-through transmission(UART), SBUS, etc, can be used for FPV security and protection, powerline inspection, mapping, border defense, etc.
Adopts IP67-grade waterproof, dust-proof, and drop-proof materials and structure, ensure not only good hand feeling but also durability.
MX16 adopts a 7 – FHD high-brightness screen, 2000 nit LCD, operators can use it in full sunlight. Support 1080P HD video transmission, the dual antenna signals complement each other, super strong signal, super long distance, with algorithm control and out-of-step frequency hopping algorithm, greatly increasing the communication ability of weak signal. The transmission distance of MX16 can reach 10KM MX16 PRO–30KM
Adopts high-energy-density lithium-ion battery, supports 18w fast charge, and can work for 8 hours on a full charge, featuring good reliability.
MX16/MX16 Pro supports HDMI, Ethernet, sensor port,2-channel serial transmission SBUS, etc. And also support lots of cameras and gimbals and other video equipment, provide development kit, SDK, and technical support, supports video suspension, supports OGC and Wireless RTSP video streaming sharing.
The use of meteorological silica gel, frosted rubber, stainless steel, and aviation aluminum alloy makes it have the ultimate hand feel, but also meets the harsh conditions of outdoor use. The MX16 is dust-proof and waterproof on the fuselage, control switches, and peripheral interfaces, which ensures the stable and smooth operation of the equipment in harsh environments.
Abundant ground interfaces, coach PPM input, and output, RJ45 network interface, long-distance connection to the intranet, Type-C Android high-speed USB interface, OTG interface can be connected to U disk, network card, etc. Expanded TF card slot.
Independent 2-dimensional gimbal control stick, easy to use.

Application Range

For multirotor,fixed-wing, vehicle, boat control and realize video (equipped with a camera), data transmission.

Specification

Radio Controller

Receiver

MIPI Camera

Diagram

FOXTECH MX16 Al in one Portable Ground Control Station-
dayagram

4G 3dB antenna 10 3-position SW4
3-position switch SW2 11 3-positionSW3
3-position switch SW1 12 knob AUX2
Left joystick XI. Y1 13 knob AUX1
Small joystick X3. Y3
Power button
6-segment switch
Button
Right joystick X2. Y2

FOXTECH MX16 Al in one Portable Ground Control Station-
fig

Using Environmental Conditions)

Environment temperature: -10 °C – +55 °C.
Storage temperature: -25 ° C – +70 ° C.
Relative humidity: no more than 65%.
Atmospheric pressure: 86 kPa to 106 kPa.
The use of the site is not allowed to explode dangerous media, the surrounding media should not contain corrosive metals and insulating gas, and conductive media, not allowed to be filled with water vapor and serious mold.
The place of use should have facilities to protect against rain, snow, wind, sand, and ash

Working Conditions

Power supply method and notes.
MX16 series ground unit has a built-in integrated rechargeable lithium battery, which is compatible with the market standard micro USB interface 5v/1.5A power adapter (such as mobile phone, camera, and other digital products USB charger) for charging.
If you encounter smoke, odor, or liquid leakage when charging on the ground unit, do not continue to it. Please transfer it to our company for repair. Beginners should pay special attention to the following safety issues! Do not charge the product in the baby’s touch area to avoid the risk of electric shock.
Do not charge this product in an environment exceeding 60 ° C

**Security

**

It is forbidden to fly when the body condition is not good. such as fatigue or drunkenness! It is forbidden to fly in bad weather such as rain or strong wind! It is forbidden to fly near high-voltage lines, communication base stations, or active places! lt is forbidden to fly at airports and other places where it is forbidden to fly!
It is forbidden to control the flight model in places where people are concentrated, in parking areas, or in other areas where property damage or personal injury may occur. Before the flight, check the equipment of the aircraft and check whether the transmit and receive system and the aircraft are normal. After the flight, turn off the power of the receiver and then turn off the power of the transmitter to prevent the engine or motor from rotating and causing damage caused by the runaway protection function! Please use a guaranteed professional charger to charge the battery. This product antenna is a fragile component, please pay attention to avoid excessive damage.

Preparation and Checking Before Use

Always check that the remote control is fully charged before use.
Please check if the antenna is placed as required before use.
For the first time, please ensure that the firmware has been upgraded to the latest version.
Users should ensure that they are not operating under the influence of drunkenness or

Proper Operation FOXTECH MX16 Al in one Portable Ground Control Station-
proper

Faulty Operation

FOXTECH MX16 Al in one Portable Ground Control Station- full opera
tion

Uav operation Diagram
Proper Operation FOXTECH MX16 Al in one Portable Ground Control Station-
fig 2

Faulty Operation FOXTECH MX16 Al in one Portable Ground Control Station-
proper opera tion

Usage

Part 1: Language Setting

Enter the system settings. select the language and input method.
After entering “Language and input method”. Click on the language to switch. add. and delete languages.

Part 2: Status Prompt Bar

Access to the internet successfully through Ethernet port or USB
Remote controller and receiver signal strength not connected in the picture
Power
Time
Return
Return to the main surface
Background task management/Split screen buttons

Part 3

FOXTECH MX16 Al in one Portable Ground Control Station- part
3

Switch the joystick control method of the remote controller.
Check the channel value of the remote control.
Check MIPI HDMI UART VIDEO and other RTSP Video
Frequency pairing between the remote controller and another receiver.
Can adjust the channel, upgrade the joystick firmware, modify the receiver serial port baud rate. Ask the technician for the password

Part4 FOXTECH MX16 Al in one Portable Ground Control Station-
vidioo

Wait for 3s-5s after the receiver is powered on, and then long-press the SET button until the white light
Enter MX16 assistant click frequency pairing. it will display ‘connected’ after the frequency is successfully matched)

Part 5

FOXTECH MX16 Al in one Portable Ground Control Station-
wifi

The factory default mode is HDMI/MIPI, used to display video transmitted via receiver MIPI/HDMI
UART VIDEO Mode display single-axis gimbal, MINI camera video(transfer board is needed)
Custom mode, display the video transmitted through the air unit ethernet port.

Part 6 Joystick calibration FOXTECH MX16 Al in one Portable Ground
Control Station- max

Check rudder quantity in the MX16 assistant, calibrate according to a reference value.

When the screen of the remote control is completely turned off, center the knob. Long press the C and D keys in the six-segment switch, then wake up the screen and slide the screen upward.
Release C and D button. and long-press D. Start the calibration when the remote control makes a sound.
Press the D button to exit the calibration mode after reaching the max and minimum values of the lett. right. small joystick and knob of the remote controller.

Part 7 FOXTECH MX16 Al in one Portable Ground Control Station-
fig

Click the System Setting icon in OGC
Click ‘general’
change the video source to RTSP Video Stream
write the video RTSP address in RTSP URL
Click ‘communication connection’
Click ‘add’
Change the type to UDP, change the listening port to 14551.
Click OK to save.

Part 8
Connect to the Internet

5Gwifi
RC WAN port connection
connect to the Internet by the wireless card through the OTG port on the remote control (support Huawei,zhongxin only).

Part 9
How to share network, video, and data information

Share the Internet connection
When the remote control is connected to the Internet via the USB wireless card, the hot spot of the remote controller can be turned on for network sharing.
Share the data link
1. Turn on the hot spot of the remote controller.
2. Connect the computer to the remote control’s hot spot.
3. Open Mission Planner, choose the TCP connection method.
Share the video link
1. Turn on the hot spot of the remote controller.
2. Connect the computer to the remote controller’s hot spot.
3. Open the computer’s settings, click on the adapter, select Ethernet, select the IPV4 protocol, select a custom IP address, enter as shown in the figure, then click on “confirm”.
Download VCL software to display the video.
Open the VLC software, Select Network Streaming in the media.
In the input field of the network URL, enter rtsp://192.168.43.1:8554/fpv_stream and click play.

FOXTECH MX16 Al in one Portable Ground Control Station- vcl
media | FOXTECH MX16 Al in
one Portable Ground Control Station- vcl media 02
---|---

FAQ

Can the remote controller install other apps?
Remote control terminal permissions are fully open, without any special software and restrictions on software installation and uninstallation.
How does the remote control enter fast charge mode?
Must use a special charger to enter the quick charge mode. There is a text prompt on the lock screen.
How to get the RTSP address if using a MIPI or HDMI camera?
Open the MX16 Assistant, open ‘video check’. Click Settings (virtual button), click the video stream address. Click Customize to copy the link staling with THE RTSP below. And then paste it
No datalink connection
check if the ground control station connects the remote control at the type of UDP if the listening port is 14551. Check if the baud rate s normal. Check if RX TX connected reversely.
Images cannot be displayed when connected to the webcam.
Images are transmitted over a network port with a dedicated RTSP address, which is not common with Mtn HDMI addresses. Please ask the webcam manufacturer for this RTSP address.
The remote control fads to connect to the Internet through an ethernet port. Please turn off WIFI when connecting the 4G network card and network port.
The remote control cannot connect to WIFI. The remote control can only connect to 5G can change the phone hot spot to 5G.