verizon Plantronics Legend UC Bluetooth Headset Instruction Manual

verizon Plantronics Legend UC Bluetooth Headset

1.  Power on your headset, and then:

• Tap and say Pair Mode, or
• Press and hold until you hear Pairing. While the headset LEDs are flashing red and blue, activate Bluetooth on your phone and set it to search for new devices.

2 While the headset LEDs are flashing red and blue, activate Bluetooth® on your phone and set it to search for new devices.
3. Select PLT_Legend.

4. Enter 0000 if prompted by your mobile phone for a passcode. Once successfully paired, the LEDs stop flashing red and blue and you hear Pairing Successful. Some phones may prompt you to allow access to contacts to enable caller name announcement.
5. Make a test call from your mobile phone.
6. Press Call to end the call. The call does not end when you remove your headset.

Pair another Phone

After pairing your headset to your phone, you may want to pair another or new phone.

1. Power on your headset, and then:

• Tap and say Pair Mode, or
• Press and hold until you hear Pairing.

2. While the headset LEDs are flashing red and blue, activate Bluetooth on your phone and set it to search for new devices.
3. Select PLT_Legend.
4. Once successfully paired, the LEDs stop flashing red and blue and you hear Pairing Successful.

NOTE : Some phones may prompt you to allow access to contacts to enable caller name announcement.

Connect PC

1. Power on your headset.
2. Insert the Bluetooth USB adapter in your PC’s USB port. The LED flashes and then turns solid blue to indicate the headset is connected to the USB adapter. You will hear PC connected. The
   The LED remains solid blue when not on an active call.

NOTE: YourBluetooth USB adapter comes pre-paired to your headset.

3. Load Plantronics Spokes software by visiting plantronics.com/software. Click Download.

NOTE: Spokes software allows you to customize your headset’s behavior through advanced settings and options.

4. Check your audio settings. Confirm the speaker and microphone settings for your PC softphone are set to Plantronics BT300.

Microsoft® Windows 7

Go to Control Panel - > Sound-> Playback and set the Plantronics BT300 device as the Default Communications Device. If you plan to listen to streaming audio, set the Plantronics BT300 device as the Default Audio Device. This is indicated by a green check mark on the Playback tab.
Go to Control Panel - > Sound-> Recording and set the Plantronics BT300 device as the Default Communications Device.

Microsoft Windows XP

Go to Control Panel - > Sounds and Audio Devices -> Audio and set the Plantronics BT300 as the default device for Sound Playback and Sound Recording.
5. Place a call from your computer softphone. The Bluetooth USB adapter flashes blue during an active call.

Re-Pair Your Bluetooth USB Adapter

If your headset and Bluetooth USB adapter become unpaired, perform the following steps:

1. Power on your headset.
2. Remove the USB adapter.
3.  Power on your headset, and then:

• Tap and say Pair mode or,

4. Insert the Bluetooth USB adapter in your PC’s USB port. Once successfully paired, the LEDs stop flashing red and blue and you hear PC connected.

Charge and Fit Headset

Three Ways to Charge Your Headset

Your headset has enough power to pair and make a few calls before charging is needed, though you may change at any time.

1. Align snap-fit magnetic areas of headset and charging device.
2.  Attach charging device to USB wall charger or laptop for 90 minutes. LEDs turn off once fully charged.

USB Cable to PC or USB Wall Charger

Charge Case to PC or USB Wall Charger

NOTE: Your charge case has an internal battery and can fully recharge your headset twice while on the go before needing to connect to a charging cable.

Charge Stand to PC or USB Wall Charger

Fit Your Headset

Replace the ear tip for a better fit.

1.  Push in the ear tip and rotate it to the left to unlock it.
2.  Align the new ear tip in the slot.
3.  Push in the ear tip and rotate it to the right to lock it in place.

To wear the headset on your other ear, rotate the boom upwards then twist it around so the ear tip is on the other side before lowering the boom.

Use and Reset Smart Sensors

Smart Sensors react when you put on or take off your headset. Putting on your headset will:

•  Answer an incoming call
•  Transfer an active call from your phone (available only with your mobile phone)
• Resume streaming audio

Taking off your headset will:

•  Transfer an active call to your phone handset (available only with your mobile phone)
•  Pause streaming audio
•  Lock the Call button to prevent accidental calls

Try Voice Commands

Tap, wait for the command request, and then say a command. For example, “What can I say?” tells you the full list of available commands.

Reset Sensors

You may need to reset the sensors if they are not working as expected. Wearing the headset, tap the Call button to test sensors:

• Talk time voice alert indicates sensors are working
• A tone indicates sensors need to be reset

To reset the sensors, charge your headset and place on a flat nonmetallic surface for more than 10 seconds.

Help and Resources

Getting Started with your Service

To learn how to manage your user account settings and site service features, go to: https://customertraining.verizon.com/virtualcommtraining.

Returning Equipment

Should you require replacement equipment, please refer to the Return Merchandise Authorization (RMA) quick reference guide located at https://customertraining.verizon.com/virtualcommtraining.

Contact Us

Support: 800–287–6235
Or visit https://customertraining.verizon.com/virtualcommtraining
For questions on other Verizon products: 800–230–9800

References

• Verizon Support | Welcome - Verizon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>