HCS RC426A Remote Control User Guide
- June 6, 2024
- HCS
Table of Contents
User guide for Remote Control RC4262001/01R
The remote control has been programmed to control your set-top box and can be programmed to control your TV.
Installing Batteries
The remote requires 2xAAA batteries. A diagram inside the battery compartment of the remote indicates proper placement of the batteries. When batteries are properly installed, the light on the remote blinks each time a key is pressed
Know your Remote
The diagram below describes each key on your remote control. Functions may vary between different services. Refer to the user guide for your set-top box for descriptions of specific functions.
STB IR key code table
1
Mute
0x0D
| | 2
Power
0x0A
---|---|---
3
Fibe
0x77
| 4
Crave
0x2F
5
NETFLIX
0x81
| 6
Prime video
0x2E
| 7
UP
0x00
|
8
LEFT
0x03
| 9
OK
0x1F
| 10
RIGHT
0x02
| 11
DOWN
0x01
|
12
BACK
0x1C
| 13
Home
0x0C
| 14
APPS
0x66
15
VOL+
0x58
| 16
Voice
0x74
| 17
CH+
0x5A
18
VOL-
0x5D
| 19
Play/Pause
0xCD
| 20
CH-
0x5F
STB RF key code table
1
Mute
0x0C/0xE2
| | 2
Power
0x0C/0x50
0x0C/0x30
---|---|---
3
Fibe
0x0C/0x7E
| 4
Crave
0x0C/0x7F
5
NETFLIX
0x0C/0x77
| 6
Prime video
0x0C/0x78
| 7
UP
0x0C/0x42
|
8
LEFT
0x0C/0x44
| 9
OK
0x0C/0x41
| 10
RIGHT
0x0C/0x45
| 11
DOWN
0x0C/0x43
|
12
BACK
0x0C/0x224
| 13
Home
0x0C/0x223
| 14
APPS
0x0C/0x1A2
15
VOL+
0x0C/0xE9
| 16
Voice
0x0C/0x221
| 17
CH+
0x0C/0x9C
18
VOL-
0x0C/0xEA
| 19
Play/Pause
0x0C/0xCD
| 20
CH-
0x0C/0x9D
Product Introduction
- This RCU is transmitting IR and RF. There is a simple set up feature for TV/Home Theatre device.
- The RCU can be set-up to control a RF or an IR STB (mutually exclusive).
- The RF platform is BLE, using HOGP as the top layer.
Before the RCU can control the STB, the RCU must pair with the STB first. - The IR protocol to control the STB is NEC. When RCU is not connected to any STB via BLE, MCU use IR to control STB.
Set STB Control Medium
-
Set to RF Mode:
Press <<OK + VOL->> simultaneously for 3 seconds; -
Clear Pairing
Press <<OK + VOL+>> simultaneously for 3 seconds;
3). Factory Reset:
Press <<OK + Home>> simultaneously for 3 seconds.
Voice Function
- Press and released
key to open the voice function, RCU will close the voice function after receiving the stop command sent by the host.
2)When RCU is recording, the STB-LED is always on.
OTA
The RCU software supports upgrade via OTA (Over-The-Air).
From diagram above, the STB can transfer the RCU firmware by the BLE link.
The OTA process can be triggered by the user using the RCU or by the STB
itself.
The RCU OTA IMAGE need to be downloaded into the STB itself. After the OTA is
completed, the RCU will have a new firmware.
Simple Setup
- Simple Setup is a feature helps user to automatically set up the remote control via STB. After being set by Simple Setup, the RCU will be able to control TV/AMP.
- Below IR function could be configured to control TV through simple setup:
TV Power, TV Mute, TV Vol+ and TV Vol-. - After a successful simple setup for TV, RCU will automatically set dual-
function keys into TV
mode
Battery Voltage Monitor
LVD check will be triggered after a signal key is released in user mode.
1.When the LVD is detected (battery voltage<2.3V);
2. While RCU works in BLE mode, it supports Bluetooth standard service of
battery level notification. The paired host is then able to get battery level
of the RCU.
Sleeping Mode
When no any activity need to do, the RC enters sleeping for power saving
purpose. The sleeping mode behaves as below:
- All LEDs are off.
- IR and RF communications are stopped.
- Any key press will wake up the RC.
FCC & IC noticement
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>