LASERCUBE Portable Laser Engraving Machine App User Manual
- June 6, 2024
- LASERCUBE
Table of Contents
LASERCUBE Portable Laser Engraving Machine
Portable Laser Engraving Machine APP
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator and your body
Overview
-
Step 1
Download APP
Scan the QR code below, download and install LaserCube APP -
Step 2
Open APP
Open the APP and read the notice and disclaimers carefully. Check and accept terms and conditions. then enter the Bluetooth List -
Step 3
Bluetooth Connection- Turn on the mobile phone’s Bluetooth function.
- Power on the device, then the Bluetooth indicator flashes and the laser lights up.
- Click the device to be connected in the Bluetooth
- List, then enter the APP Home page after successful connection.
Note: The laser lights up after power on is only an indicator light, not in the engraving state. If the device is not displayed in the Bluetooth list, click below and wait for a second and try again
-
Step 4
Home Page- Camera: Click and enter the Camera page.
- Photos: Click and enter the Photos page.
- Create: Click and enter the Create page.
- Library: Click and enter the Library page.
- More: Click I’m on the upper right for more settings.
-
- Steps 5
Get a Picture
User can get a picture for engraving by [Camera], [Photos], [Create] or [Library].
- Steps 5
-
-
Camera
Take a photo with a mobile phone camera. Resize the photo then click and enter the Adjust Picture page.
Note: Access to a mobile phone camera is required. -
Photos
Select a photo from the mobile phone album. Resize the photo, then click and enter the Adjust Picture page. -
Create
Users can use either [Text] or [Drawing] to create. -
Text
Users can create text content in this page. After the creation, click and enter the enter Adjust Picture Page -
Drawing
User can draw a picture freely in this page. After the creation, click and enter the enter Adjust Picture page. -
Library
select a picture from the APP Library. Resize the picture, then click and entertheenter Adjust Picture page.
-
-
Step 6
Adjust Picture
Choose one of the picture adjustment modes below. Click and enter the Edit Picture page. -
Step7
Edit Picture- Trim: Click and enter the Trim page.
- Text Click and enter the Text page.
- Eraser. Click and enter the Eraser page.
- After editing, click and enter the Engraving Settings page.
-
- Trim: user can trim the picture to a specific shape or size.
- Free: Length and width can be scaled at any scale.
- 1:1: Length and width are scaled equally.
- Circle: Trim with a circular area.
- Click to save and return to Edit Picture page.
-
Text
Users can add text to the picture. Click to save and return to the Edit Picture page. -
Eraser
User can erase the contents on the picture. Click to save and return to Edit Picture page. -
Steps 8
Engraving Settings- Size: Enter the engraving size, maximum 100mm.
- Material: Select according to the material to be engraved, engraving power and depth will be adjusted accordingly.
- Power: Adjust the power of the laser.
- Depth: Adjust the engraving depth.
- Times: Select the number of times of engraving.
After setting, click [Next] to enter the Preview page.
-
Step 9
Preview- Click [Preview] to turn on the laser, and the laser will move around the engraving area.
- If the engraving area is good, click [Next], and then user will be prompted to enter the security code.
- Enter the correct security code, then enter the Upload page and ready to engrave.
-
- Step 10
Upload
- Step 10
-
- User can check the upload progress and time in this page.
- Click [Cancel] to stop uploading and return to Home page.
- After uploading, engraving will start automatically
-
Step 11
Engraving -
- User can check the engraving progress and time in this page.
- Click [Pause] to pause engraving, then click [Resume] to continue engraving.
- Click [Stop] and will be prompted to confirm stopping engraving. Engraving cannot be resumed after stopping.
-
Step 12
Finish -
- Click [New Engraving] and return to Home page.
- Click [Engrave Again] to engrave the same content of this engraving again.
More Settings
- Bluetooth
- Notice
- Contact Us
- About LaserCube
Bluetooth
The Bluetooth list shows the devices that can be connected.
There will be a behind the connected device.
Click the connected device to disconnect.
If the device is not in the list, click Allison the upper right and wait for a
second to try again.
Notice
Warning, notice, safety guide and disclaimers.
Contact Us
Contact information of TronHoo.
About LaserCube
Users can view version information on this page.
- App Upgrade: Click to upgrade APP version.
- Firmware Upgrade: Click to upgrade firmware version of the device.
Note: Long press the LaserCube logo can access Adjust Laser page.
Adjust Laser
This page can be accessed by long pressing the LaserCube logo in about
LaserCube page.
The laser of the device has been adjusted before leaving the factory. Do not
adjust the laser at will, otherwise the device may not work well.
If the laser deviate from the center due to accident, it can be fixed in the
page.
If the laser is off, click [Turn on Laser] to light up the laser.
After adjusting, click [Save] to save the setting. Click to return.