Calibre Mecca NRCR3290d 32mm Ambulant 90 Degree Bent Tube Grab Rail Instruction Manual

Mecca Care
32mm Ambulant 90 Degree
Bent Tube Grab Rail 450X450MM

Drawing

Specifications

SKU
NRCR3290d
Warning:
These rails are designed to be mounted onto wall studs or masonry walls.
Installation is recommended to be completed by qualified trades person who complies with the AS 1428 1-2009 design for access and mobi ity standard.
It is recommended rail location is determined by a qualified occupational therapist or trained professional to the AS 1428.1-2009 standard. Correct installation is required to ensure safe, long term operation. Incorrect mounting can result in reduced capac ty of the rail which can result in injury to user and damage to the wall.

Features

1. Australian owned and designed.
2. Sizes: 45 / 90 degree as standard.
3. Can be mounted on left or right hand s de.
4. Optional add on toilet roll holder attaches to the 32mm rail
5. Modular design, the rail to be mounted horizontaly, vertically or at any angle and cut down to suit your bathroom 150kg capacity for all 25mm and 32mm diameter grab rails.
6. 32mm diameter rails are approved for standard AS1428.1 requirements in DDA bathrooms.
7. Gun metal, brushed gold and brushed bronze colours are PVD coated for long term durability.

Finish

| Chrome
NRCR3290dCH
---|---
| Gun Metal
NRCR3290dGM
| Brushed Bronze
NRCR3290dBZ
| Matte Black
NRCR3290dMB
| Brushed Gold
NRCR3290dBG
| Brushed Nickel
NRCR3290dBN

*Dimensions are nominal measurements only.

Installation Instruction

| 1. Locate wall studs, install into at least one stud.
Place wall seal/mounting bracket on wall at correct height over centre of stud and mark hole positions on wall refer left picture. (minimum 2 supplied screws per bracket).
Tip: Rail height is 790mm above the ground.
---|---
| 2. Drill pilot holes into wall stud approximately 60mm deep to suit mounting screws (and wall plugs if required).
Tip: 3mm hole for screws into timber or 8mm hole for wall plugs.
| 3. Apply small amount of silicon to mounting brackets and wall in and around the screw holes.
| 4. Install mounting brackets by screwing onto wall.
Tip: Use appropriate mounting screws for the wall stud material, supplied screws are for timber wall studs.
| 5. Disassemble parts firstly refer to left picture.
(a)Make a marker at 390mm of rail, slide the 32mm ring onto the marker of rial tubes and tighten the M4 screw by allen key.
(b)Fix the 16mm rod to the ring with M4 screw.
(c)Install the 25mm rial onto 16mm rod by screw.
| 6. Slide rail tubes into end brackets and push onto wall brackets,refer to left picture.
Tip: Rail length can be cut down to a smaller size, simply use an angle grinder, hacksaw or pipe cutter then deburr the end with a file or grinder and reinsert into the end bracket.
| 7. Tighten grub screws with allen key.
Tip: If rail rattles, loosen end bracket, twist slightly and tighten.
| 8. Finished.
Tip: Optional add on toilet roll holder attaches to the 25mm rail, refer to left picture.

info@nerotapware.com.au
nerotapware.com.au
11-13 Buontempo Road
Carrum Downs Vic 3201
MECCA CARE
DDA CARE 32MM
www.nerotapware.com.au
Mecca Care 32mm Ambulant 90 Degree Bent Tube Grab Rail 450X450MM -Manual

References

• Nero Tapware | Premium Tapware for Australia & New Zealand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>