Anwsti 70040002 Universal Series Dali Dimmer Instructions
- June 6, 2024
- Anwsti
Table of Contents
Anwsti
Universal series DALI dimmer
Important: Read All Instructions Prior to Installation
Function introduction
Product Data
No| Input Voltage| Output Current| Output Power| Remarks| Size(LxWxH)| DALI
Consumption| Dimming Range| Ambient Temperature
---|---|---|---|---|---|---|---|---
1| 12-36VDC| 4x5A| 4x(60-180)W| Constant voltage| 178x46x22mm| 2mA| 0.1%-100%|
-20℃ ~ +50℃
2| 12-36VDC| 4x350mA| 4x(4.2- 12.6)W| Constant current| 178x46x22mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
3| 12-36VDC| 4x650mA| 4x(7.8-23.4)W| Constant current| 178x46x22mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
4| 12-36VDC| 4x700mA| 4x(8.4-25.2)W| Constant current| 178x46x22mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
4| 12-36VDC| 4x900mA| 4x(10.8-32.4)W| Constant current| 178x46x22mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
- In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2.
- Built-in DALI-2 interface, DALI DT6 device
- Match all DALI systems in the market
- Manual /automatically DALI address setting
- DALI address digital indicate
- Four channels can set addresses from one to four.
- To work with a power repeater to expand output power unlimitedly.
- Waterproof grade: IP20
Safety & Warnings
- DO NOT install with power applied to the device.
- DO NOT expose the device to moisture.
Operation
Set DALI Address Manually Via Buttons
1.1. Press and hold down any of the two buttons until the numeric digital
display flashes, then release the button.
1.2. Click any of the two buttons once to select a digit, click again to
change the digit until the desired DALI address appears. Click the first
button to set the “tens” position and the second button to set the “units”
position. The address can be set from 00~63.
1.3. Then press and hold down any of the 2 buttons until the numeric digital
display stops flashing to confirm the setting.
Note: DALI address can be manually assigned from 00-63-FF, by factory defaults, no DALI address is assigned for the dimmer, and the display shows . Setting DALI address as will reset the dimmer to factory defaults.
Set DALI Address Quantity
1.1. Press and hold down both of the two buttons until the numeric digital
display flashes, then release the button.
1.2. Click the first button to select “1A”, “2A”, “3A” or “4A” which means 1
address, 2 addresses, 3 addresses or 4 addresses.
1.3. Then press and hold down any of the 2 buttons until the numeric digital
display stops flashing to confirm the setting.
For example, when we set the address to 22:
When selecting 1A, all four channels will be the same address 22.
When selecting 2A, channels 1 & 3 will be the same address 22, channels 2 & 4
will be the same address 23.
When selecting 3A, channels 1, 2, 3 will be addressed at 22, 23, 24
respectively, and channel 4 address is also 24.
When selecting 4A, channels 1, 2, 3, 4 will be addressing 22, 23, 24, 25
respectively.
DALI Address Assigned by DALI Masters
DALI address can also be assigned by the DALI Master controller automatically,
please refer to user manuals of compatible DALI Masters for specific
operations.
Note: The digital display will show When the DALI master is assigning
addresses. Wiring diagram
Conformity & Standards
- Radio Frequency Interference according to EN 55015:2013
- Immunity standard according to EN 61547:2009
- TÜV Rheinland marked, CE marked
Product Dimension
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>