H Koenig MXK32 Blender Instruction Manual

Instruction Manual

Blender

https://goo.gl/UPdnGn

In order to let the product better work for you, please read the instruction before using it. Please put away well the instruction after reading for consulting in later days.

ATTENTION :

• Wrong operation and improper handling can cause problems with the appliance and injury to the user.
• The unit may be used only for the intended purposes. No liability is accepted for damages arising from improper use or faulty handling.
• Before connecting to the mains, please check whether the type of supply and the mains voltage matches with the details given on the nameplate on the appliance.
• Do not immerse the appliance and mains plug in water or other fluids. Should the appliance still fall in water sometimes, pull out the power plug immediately and have the appliance checked by an expert before using it again? There is a danger to life from electrical shock!
• Do not try to open the housing yourself! Do not introduce any kind of object into the housing.
• Do not use the appliance with wet hands, on a moist floor, or when the ambiance is humid
• Do not hold the mains plug with wet or moist hands.
• Check the mains plug and mains adapter regularly for damages. If the supply cord or plug is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
• Do not operate the appliance, if the power cable or the mains plug shows damage or the unit falls to the floor or has been damaged otherwise. In such cases, bring the unit to the workshop for checking and repairs, if necessary.
• Do not ever try to repair the unit yourselves. There is danger from electrical shock!
• Do not let the power cord hang over sharp edges and keep it away from hot objects and open flames. Pull the plug itself to remove it from the plug socket.
• Installation of a spike protector will offer additional protection with a nominal trigger current of not more than 30 Ma in the house installation. Please consult your installing electrician.
• The cable as well any extension cable required should be laid such that there will not be any risk of anyone pulling it inadvertently or tripping over it.
• If a long extension cable is used, it must be suitable for the power supply in question. Otherwise, it causes overheating of the cable and/ or plug. l Set the unit on a rigid, flat, and heat-proof surface, not near open flames (such as a gas oven), and operate it out of reach of children.
• This appliance is suitable neither for commercial use nor for use outdoors.
• Children cannot sense the dangers caused by improper handling of electrical devices.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety
• Pull out the plug out of the socket, when the appliance is not in use and also before cleaning.
• Caution! The appliance is on power so long as it is connected to the power circuit.
• Care shall be taken when handling the sharp cutting blades, emptying the bowl, and cleaning.
• Avoid to potential injury from misuse
• Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
• Switch off the unit before pulling out the mains plug.
• Use only spare parts from the manufacturer or his local dealer.
• Never carry the unit by its power cord. l Do not remove individual housing components.
• When mixing hot liquids/foods excess pressure may build up inside the blender, and this could make the lid come off and the contents splash out. We, therefore, recommend that you avoid mixing excessively hot foods and that you only put very small quantities of hot liquids or foods into the blender.
• Do not use the blender for very hard food products, such as bones, shelled nuts, frozen meats, etc., which could either damage the blade or cause the motor to seize.
• The device must not be used if it has been dropped, it obvious signs of damage are visible, or if it has leaks.
• This appliance may be used by children of at least 8 years of age, as long as they are supervised and have been given instructions about using the appliance safely, and are fully aware of the dangers involved.
• Cleaning and maintenance should not be carried out by children unless they are at least 8 years of age and are supervised by an adult.
• Keep the appliance and its power cord out of reach of children under 8 years of age.
• When using electrical equipment, safety precautions must always be taken to prevent the risk of fire, electric shock, and/or injury in the event of misuse.
• Make sure that the voltage rating on the type plate corresponds to the main voltage of your installation. If this is not the case, contact the dealer and do not connect the unit.
• Never leave the unit unattended while in operation.
• Please keep this document at hand and give it to the future owner in case of transfer of your device.
• Do not use outside.
• The device is not intended to be operated by external timer means or a remote control system.

Caution:
Switch off the unit before cleaning it to avoid creepage and other dangers. When the plug or power cord has been damaged, do not use the unit, even not disassembly by yourself, must be informed by the after-service center to handle it.

SPECIAL SECURITY PRECAUTIONS

• Caution: The blades of the jug are very sharp. There is a danger of injury! While the blades are turning, never touch the jug from the inside and never put any objects inside.
• Only use equipment endorsed by the manufacturer.
• Only use the unit with tightly closed cover and inserted closure.
• The unit is equipped with a security function. The unit can only be switched on if the jug is put on the engine base properly. If the unit cannot be switched on, pull the power cable and check the connection between jug and engine base.

PARTS ITEM

INSTALLATION

1. Clean the measuring cup, cover and jar (except main body), and so on before first using.
2.  To make sure the unit is turned off and not to connect before installation.
3. First ring the jar sealed ring into blade base, then enclose the blade base into the jar, last rock the jar slightly causing it to lock into place.
4.  Fit the blender glass jar onto the main body, and turn it slightly clockwise so it locks with the motor section. Fill the jug with the desired foods. Please ensure the water not spillover from the cup. (Maximal water capacity cannot exceed 1500 ml) DO NOT USE THE UNIT WITHOUT ANY MATERIAL INSIDE.
5. Put the cover on top of the jar and push it down. Insert the closure into the cover and turn it till it locks into place.
6. Place the measuring cup on the center of the cover, anticlockwise rock the measuring cup slightly.

OPERATION

1. Connect the power.
2. This unit has a safety design, it does not work if the jar is not installed on the main body properly.
3. Turn the turning knob P/0/1/2/3/4/5 to position 0 in order to make sure the unit is turned off.
4. Fill the jug with the desired foods
5. Put the cover on top of the jar and fix it. Place the measuring cup on the center of the cover, anticlockwise rock the measuring cup slightly.
6. Put the blender glass jar onto the main body, and turn it slightly clockwise so it locks with the motor base. and the machine was fully assembled.
7. Turning the knob to the required speed (P—pulse, grade 1 to 5 means speed of blades from low to high).
8. During working mode, the blue light around the knob is on. 

Speed adjust:

P—pulse –Stainless steel blade operates with transitorily highest speed, suitable for ice.
1—Stainless steel blade operates with low speed.
2—Stainless steel blade operates with a higher speed than grade 1 but lower speed than grade 3.
3—Stainless steel blade operates with a higher speed than grade 2 but lower speed than grade 4.
4—Stainless steel blade operates with a higher speed than grade 3 but lower speed than grade 5.
5—Stainless steel blade operates with a higher speed than grade 4 and it is the highest speed of the machine.
0—turn off the unit.

Caution:

1. Over-filled can block the operation, please turn off the unit and do not connect the plug, take out some of the material, then operate.
2. Do not use the unit continuously for more than 2 minutes.

CLEANING AND STORAGE

• In addition to this, you must refer to the security precautions.

• Do not clean the Motor main body, power cord, and plug with water.

• Clean the engine base with a soft, wet piece of cloth and some mild cleaning agent.

• Fill the jug half-full with hot water and a little cleaning agent. Let the unit run on speed 2 until the jug is clean.

• The jar base bottom with the blades can be taken apart. Screw off the base boom counter-clockwise which is marked “un-lock” on the bottom. Take out the blades together with the sealing ring facing upwards.

• Now clean jug, cover, closure, base, and blades with a sealing ring with hot water and some cleaning agent. Dry well before re-using. Caution! The blades inside of
  the jug are very sharp.

• Never use aggressive cleaning agents.

Warning:
Do not to touch the sharp blade. When clean, please wipe by dishcloth, to avoid accidentally injure.

Note:

1. Unit suitable for household only.

2. Overheat protection
   In order to prolong the device’s service life, an overheat protecting unit is installed. If the motor runs too long or overloaded, the temperature reaches the warning value and the motor will stop automatically. Pull out the power supply plug and wait for the motor to cool (about 20 to 30 minutes), then use it again.
   If you have any problem with this device, do not disassemble it by yourself. Always contact the service department or after-sale service department.

3. Do not use for commerce. Otherwise, the maintenance service will be invalid.

CLEANING

Cleaning the Blender Jug

1. Pour about 500ml of warm soapy water into the jug and place the jug on the base.
2. Use the pulse mode to loosen any food particles and free them from the blades.

• Remove the jug, pour away the water, and rinse in fresh running water. Repeat steps 1 and 2 with fresh water.

• Alternatively, the jug may be immersed in warm soapy water and cleaned using a long-handled brush. Do not touch the blades when cleaning.

• Wash the lid and measuring cup separately in warm soapy water, rinse and allow to dry.

• The jug body should be handled carefully. The jug contains moving parts- do not leave the jug immersed in water for longer than necessary to clean it or you may affect the
  operating performance of the blender.

• Handle blades with care especially during cleaning as they are extremely sharp.

• DO NOT wash the jug or attachments in a dishwasher.

Although it is not advisable to take apart the jug base with the blades, in case you have taken it apart, you should re-install the parts back in the correct order.

1.  Fit the rubber Sealing Ring first securely under the blades. Caution! The blades are very sharp.

2. Assemble the fitted Sealing Ring and blades into the jug base.

3. Fit the plastic Locking Ring into the jug base and rotate it tightly.

Cleaning the Base

1. Ensure the blender is switched off and unplugged from the mains.
2. Wipe the outer surface of the motor unit with a damp cloth. Never use abrasive cleaners or scouring creams.

Never immerse the base in water when cleaning.

ENVIRONMENT

CAUTION:
Do not dispose of this product as it has with other household products. There is a separation of this waste product into communities, you will need to inform your local authorities about the places where you can return this product. In fact, electrical and electronic products contain hazardous substances that have harmful effects on the environment or human health and should be recycled. The symbol here indicates that electrical and electronic equipment should be chosen carefully, a wheeled waste container is marked with a cross.

Adeva SAS / H.Koenig Europe –
8 rue Marc Seguin – 77290 Mitry Mory – France
www.hkoenig.com
– sav@hkoenig.com –
contact@hkoenig.com –
Tél: +33 1 64 67 00 05

References

• H.Koenig : Le spécialiste du petit électroménager

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>