Silkn H3101 Infinity IPL Permanent Hair Removal Device User Manual

: June 6, 2024
: Silkn

Infinity
**H3101
USER MANUAL

**

Silk’n Infinity

Warnings

This user manual is based on the standards and rules in force in the European Union. When abroad, you must also observe country-specific guidelines and laws.

Before first use, please read this user manual in full, and keep it for future use. We recommend you refamiliarise yourself with the instructions before each treatment.

Always keep the device or any of its parts dry. Ensure that your hands are dry before connecting the adapter to the electricity supply.
Do not use the device in the bathroom.
Never use the adapter if it has a damaged cable or plug, isn’t working properly, or has been submerged in water. If that happens, unplug the adapter immediately before touching it. Failure to unplug the adapter may result in an electric shock!
Do not operate the device in environments where there is a risk of explosion. The device is not suitable for use in the presence of a flammable anesthetic mixture with air, oxygen, or nitrous oxide. Keep the device and all its parts away from open flames and hot surfaces.
Keep the adapter accessible at all times, so it can be removed from the electricity supply easily in case of emergency.
Always switch the device off and disconnect it from the electricity supply when you are not using the device when you intend to clean it, or in the event of a fault.
Never pull the adapter out of the socket by the cable. Always remove it by taking hold of the adapter.
Do not kink the adapter cable or lay it over sharp edges. Place it in such a way that it does not pose a tripping hazard.
Possible hazardous optical radiation is emitted from this device. Do not look at the operating lamp. Eye injury may result.
Do not use the device where there is monitoring equipment (e.g., cardiac monitors, ECG alarms), which may not operate properly when the device is in use.
Do not use if the parts or accessories are not supplied by the manufacturer as defined in this manual, or if the device is damaged in any way, does not appear to be working
properly, or if you see or smell smoke.
Do not attempt to modify, open or repair the device. You may expose yourself to an electric shock. It will also void the warranty.
Children must not play with the device or any of its parts. They may injure themselves or swallow small parts and choke.

Contraindications

The device is suitable for adults aged 16 years and above.
The device must not be used by the following people: children, adults with limited physical, sensory or psychological capacities, or those lacking experience or knowledge in how to use the device.
The device is not designed for everyone. Hair removal by intense pulsed light sources can cause increased hair growth in some individuals, although it is extremely rare (less than 1% of the population). Potential areas for women are the face and neck, and for men, the back, shoulders, and upper arms, although it could also affect other areas. The highest risk groups are people from the Mediterranean,
The device is not suitable for use on children or animals.
Do not use the device if you:
have a pacemaker or an ICD.
have naturally dark skin (refer to the skin color chart at the front of this user manual). Treating dark skin can result in adverse effects such as burns, blisters, and skin color changes (hyper- or hypopigmentation).
have naturally white, grey, light blond, or red body hair.
are pregnant or nursing.
have a history of keloidal scar formation.
have suffered or suffer from epilepsy.
have a disease related to photosensitivity, such as porphyria, polymorphic light eruption, solar urticaria, lupus, etc.
have a history of skin cancer, a current condition of any cancer, or areas of potential skin malignancies.
have received drugs from your physician for a skin condition within the past 6 months.
are allergic to metal, or are sensitive to contact with chrome.
have any other condition that in your physician’s opinion would make it unsafe for you to use the device.
cannot sense heat properly because of an illness, or another health-related issue.
Do not use on these parts of the body:
on tanned skin.
around or near the eyes. Use below the cheekbones.
on tattoos or permanent makeup, dark brown or black spots (such as large freckles, moles, or warts), nipples, genitals, around the anus, or lips.
areas with injected fillers or toxins.
a part of the body that has a history of herpes outbreaks.
skin that has active eczema, psoriasis, lesions, open wounds or infections (cold sores), abnormal skin conditions caused by systemic or metabolic diseases (diabetes for example).
areas that are prone to rosacea.
on varicose veins.
areas that are painful.
areas where you may want hair to grow later. The results are permanent.

Safety features

With Silk’n safety comes first

Enhanced Home Pulsed Light™ (HPLC) technology provides superior safety with lower energy levels. eHPL achieves long-term hair removal results at a fraction of the energy level used in other light-based hair removal equipment. The technology combines 2 energy sources: galvanic energy and optical energy. The galvanic energy enables better penetration of the optical energy to the hair shaft by temporarily widening the skin pores. The hair shaft absorbs the light, deactivates the hair follicle and hair growth is disabled.
The low energy reduces the risk of harm or complications and contributes to your overall safety.

3.1 Skin protection
Light-based hair removal is not suitable for tanned skin.
The device comes with a built-in skin color sensor (#3) that is designed to measure the complexion of the applied surface and enables energy levels according to skin complexion.
Furthermore, the treatment surface (#2) , through which pulses of light are delivered, is recessed inside the device. This enables the device to protect your skin by avoiding direct contact between the treatment surface (#2) , and the skin.

3.2 Eye protection
The device has a built-in safety feature for eye protection. It has been designed so that a light pulse cannot be emitted when the treatment surface (#2) is facing open air. The safety feature enables treatment only when the treatment surface (#2) is in contact with the skin.

3.3 Exposure to the sun

Sun exposure includes constant unprotected exposure to direct sunlight for over 15 minutes, or constant unprotected exposure to diffuse sunlight for over 1 hour.
Do not use on tanned skin after recent sun exposure, including tanning machines. Using the device on skin that has been recently exposed to sunlight can result in adverse effects such as burns, blisters, and skin color changes (hyper- or hypopigmentation).
Avoid further exposure to the sun for 4 weeks before and 2 weeks after your treatment. This is because higher quantities of melanin expose the skin to greater risk when using any method of light-based hair removal. This applies to all skin types, even those that don’t seem to tan quickly.

Get to know your device

4.1 Device description
The device is a light-based device for permanent hair reduction designed for home use. It is a powerful electrical device and should be used with special attention to safety.
4.2 Intended use
The IPL device is an over-the-counter device intended to remove unwanted hair and affect long-term, or permanent hair reduction.
Permanent hair reduction is defined as a long-term stable reduction in the number of hairs regrowing after a treatment regime. You may use the device to remove unwanted body hair.
Ideal body areas include the underarms, bikini line, arms, legs, face (below the cheekbones), back, shoulders, and chest.
The device is a medical appliance and is intended exclusively for cosmetic treatments. It is for private use and is not suitable for commercial or therapeutic use.
The device is for self-treatment only. Do not use the device on anyone but yourself.
Do not use it for any purpose other than as described in this manual.
4.3 Package contents

Hair removal device
Adapter with cable
Cleaning cloth
Storage case
User manual
Warranty booklet

4.4 Device parts
Refer to the diagram on page (i) at the front of this manual to see the location of each feature.

Pulse button (#1)
Treatment surface (#2)
Skin color sensor (#3)
Bluetooth indicator light (#4)
Energy level indicator lights (1-5 ) (#5)
Control button (#6)
Ready light/skin tone warning indicator light (#7)
Base electrode (#8)
Touch electrode (#9)
Adapter socket (#10)

4.5 Device controls

Control	Function / Mode

Control button (#6)

| • Long press turns the device on or off.
• Short press: each press increases the energy level. When at energy level 5, the next press moves back to energy level 1.
Pulse button (#1)| Triggers a light pulse.
Base electrode (#8)| Triggers a light pulse when pressed together with the pulse button.
Ready/skin tone warning indicator light (green) (#7)| • Green constant: when the device is turned on.

• Light off: the device is getting ready for the next pulse.

• Green blinks: cannot detect the skin color.

Energy level indicator lights (green) (#5)| • Green constant: the energy level is active.

• The energy level 1 indicator light is green constant when the device is turned on.

• The number of energy level indicator lights corresponds to the energy level selected.

Bluetooth indicator light (blue) (#4)| • Blue constant: Bluetooth is active.

4.6 Energy levels

The energy level determines the intensity of the light pulse delivered to your skin. As the energy level increases, so do the results, as well as the risk of possible side effects and
complications (see section 5.3 Possible side effects).
The device has 5 levels of energy from 1 (the lowest) to 5 (the highest), represented by 5 energy level indicator lights (#5). To change levels, short press the control button (#6).
To determine the right energy level for your treatment area, refer to section 6.3 Perform a spot test.

4.7 Device sensors
The device has sensors for touch and color.

Touch: The device will only emit pulses when it is in firm contact with your skin.
Colour: Light-based hair removal on darker skin tones may result in adverse effects such as burns, blisters, and skin color changes (hyper- or hypopigmentation). The device has a skin color sensor (#3) that detects the color of your skin automatically. The skin color senso r (#3) checks your skin color at the start of, and occasionally during, each treatment.
If the device detects that your skin tone is too dark for safe use, the ready light/skin tone warning indicator light (#7) will blink.

4.8 Pulsing and gliding

Whether you decide to pulse or glide:

Avoid gaps or overlaps as you use the device. Overlaps increase the likelihood of adverse effects.
Do not treat the same area of skin more than once per treatment session.
Pulsing is the best technique for treating specific spots or small areas.
Press the treatment surface (#2) against your skin. Work in rows (either across or down as shown in the image). Start at one end of each row and progress to the other end.
The treatment surface (#2) creates temporary pressure marks on the treated area so you can see areas you have treated.
After each pulse, move the treatment surface (#2) to the next spot. Keep doing this pulsing action for the area you are treating.
Gliding is the best technique for treating larger parts of the body.
Press the treatment surface ( #2) firmly against your skin and slowly glide over your skin (either across or down as shown in the image). Make sure that the treatment surface (#2) is always touching your skin.
At lower energy levels, the device takes only 1-1.5 seconds to recharge between pulses. This generates a nonstop sequence of flashes.

Treatments

5.1 Treatment plan
The efficiency of hair removal varies from person to person according to body area, hair color, and how the device is used. A typical full hair growth cycle may take 18-24 months. During this time, multiple treatment sessions are required to achieve permanent hair reduction.

A typical hair removal plan during a full hair growth cycle includes:

Treatments 1-4: Plan two weeks apart.
Treatments 5-7: Plan four weeks apart.
Treatments 8+: Treat as needed, until desired results are achieved.

Ideal body areas include underarms, bikini area, arms, legs, back shoulders, and chest (excluding nipples). For the face, use below the cheekbones but not around or near the eyes or lips.

Skin Type’| Body Haire| Light Fluence [J/cm2]| Part of the Body| Average Treatment Time| Effectiveness of Hair
Reduction
---|---|---|---|---|---
1-6| Dark blond
to brown| 2.5-4| Lower or
upper legs| Sessions 10-12 an approx. 4 weeks apart| 60%
Arms| 50%
Bikini line| 60%
Underarms| 55%
1-6| Brown to black| 2.5-4| Lower or
upper legs| Sessions 8-10 approx. 4 weeks apart| 70%
Arms| 60%
Bikini line| 70%
Underarms| 65%

The individual response depends on hair type as well as biological factors that may affect hair growth patterns. Some users may respond quicker or slower than the average number of treatments.
One cannot expect permanent hair reduction in single or even double treatment sessions. The duration of the resting period for hair follicles also depends on the body area.

5.2 What to expect with the device
During a treatment session it is normal to experience and feel:

A fan noise: The cooling fan makes a noise similar to that of a hairdryer.
A pop sound with each pulse: When a pulse of eHPL light is activated, it is normal to hear a subtle pop sound simultaneously with the flash of light.
A sensation of warmth and tingling: During each galvanic pulse sequence it is normal to feel a mild sensation of warmth and tingling from the galvanic and optical energies.
Some mild red or pink color: During and just after your treatment session it is not uncommon to see some very mild, pink-like color of the skin. This is usually most noticeable around the hairs themselves.
Stop use immediately if you see full redness of the skin, blistering, or burns.

5.3 Possible side effects
When used according to the instructions, side effects and complications associated with the use of the device are uncommon. However, every cosmetic procedure, including those designed for home use, involves some degree of risk.
Therefore, it is important that you understand and accept the risks and complications that can occur with pulsed light hair removal systems designed for home use.
There is a minor risk that stacking or overlapping multiple pulses on the same skin spot may have some adverse effects.

Minor skin discomfort
Home pulsed light hair removal is generally well-tolerated.
However, some users feel mild discomfort during use. This is best described as a mild stinging sensation on the treated skin areas. The stinging sensation may last during or after treatment.
If you feel pain and notable skin irritation during treatment, reduce the energy level. If that doesn’t help, stop the treatment.
Skin redness
Your skin may become red immediately after using the device or within 24 hours. Redness generally clears up within 24 hours.
See your doctor if the redness does not go away within 2 to 3 days.
Make sure you use an energy level that is comfortable for you and suitable for your skin color.
Excessive redness and swelling
In rare cases, the treated skin may become very red and swollen. This is more common in sensitive areas of the body. The redness and swelling should subside within 2 to 7 days and should be treated with frequent applications of ice. Gentle cleansing is OK, but avoid exposure to the sun.
Increased sensitivity of the skin
The skin of the treated area is more sensitive so you may encounter dryness or flaking of the skin.
Blisters or burns; skin wounds
It is very unusual but blisters, burns, or wounds to the skin may occur following treatment. These can require a few weeks to heal, and in very rare cases, may leave a noticeable scar.
Cool the affected area and apply anti-burn cream. Wait until the area has healed completely before another treatment, and use a lower energy level. If the skin does not return to normal within 3 days, consult your physician.

Infection or bruising
Infection of the skin is exceedingly rare but is still a possible risk following a skin burn or wound caused by the device.
Very rarely, the device may cause blue-purple bruising that can last 5 to 10 days. As the bruising fades, there may be a rust-brown discoloration of the skin (hyperpigmentation).
Scarring
Although very rare, scarring may occur. Usually, the scar is in the form of a flat and white lesion on the skin (hypertrophic). However, it can be large and red (hypertrophic) or large and extend beyond the margins of the injury itself (keloid). Subsequent aesthetic treatments may be required to improve the appearance of the scar.
Pigment changes
The device targets the hair shaft, in particular the pigmented cells in the hair follicle and the hair follicle itself. Nevertheless, there is a risk of temporary hyperpigmentation (increased pigment or brown discoloration) or hypopigmentation (whitening) to the surrounding skin. The risk of changes in skin pigmentation is higher for people with darker skin tones or heavily tanned skin. Usually, discoloration or changes to skin pigment are temporary, and permanent hyperpigmentation or hypopigmentation is rare.
Stop use immediately if any of these side effects are more severe.
See your physician if the side effects do not go away within 2 to 3 days.

Get started!

6.1 Connecting the device

Remove the device and other components from the box.
Plug the adapter into the adapter socket (#10) and plug the adapter into the electricity supply. All energy level indicator lights (#5) will turn on, and then go off.

6.2 Pre-treatment preparation
Remove all jewelry on or near the treatment area before use.

Before treating an area, the skin should be shaved, clean, dry, and free of any powders, antiperspirants, or deodorants. Do not wax, pluck, or tweeze the hair out.
Never use flammable liquids such as alcohol (including perfumes, sanitizers, or other applications containing alcohol), or acetone to clean the skin before use.
Do not use the device if the treatment surface (#2) is broken or missing.
Be sure to cover up moles, warts, or other marks on the skin that should not be treated. Use a material that does not absorb the light such as a white cloth or white medical tape.

6.3 Perform a spot test
You must decide which energy level is right for your skin, and the area you want to treat. For example, you might treat one area at energy level 1, and another at level 4.
To choose the right energy level, test each treatment area separately (refer to the skin colour chart at the front of this manual).
Repeat this spot test for each part of the body you wish to treat.

Press the control button (#6) to turn on the device. The level 1 energy level indicator light (#5) will go on.
Place the treatment surface (#2) on your skin and press the pulse button (#1) to deliver one pulse. Make sure your hand touches the base electrode (#8) together with the pulse button (#1). When the treatment surface (#2) is in full contact with the skin, the ready/skin tone warning indicator light (#7) will start blinking slowly.
If you do not experience abnormal discomfort press the control button (#6) again. This will increase the energy level.
Press the pulse button (#1) with your hand touching the base electrode (#8) to deliver another pulse on a different spot at energy level 2. Continue testing at increased energy levels. Use the energy levels indicated on the skin colour chart. When you find the highest energy level that is comfortable for that treatment area, you can start your treatment.
Use a lower energy level if you experience discomfort.
You are now ready to perform a treatment.

6.4 Treatment steps

Press the control button (#6). The device will turn on, the level 1 energy indicator light will be on, and a fan sound will start.
After pressing the control button (#6) , the ready/skin tone warning indicator light (#7) will turn on. The device is then ready to use at the lowest energy level. Always start at energy level 1 for your first treatment.
Set the energy level. Press the control button (#6) repeatedly to increase the energy level until you have the level you want. The energy level indicator lights (#5) indicate the energy level setting (see section 4.6 Energy levels). The number of energy level indicator lights (#5) that are on, indicates the energy level selected.
Decide if you wish to treat the area by Pulsing or Gliding (refer to section 4.8 Pulsing and gliding).
Apply the treatment surface (#2) to the skin. Press the pulse button ( #1 ). The device will first determine the color of your skin automatically. If the skin colour is light enough for safe application, the device will activate the galvanic energy. You will feel a mild sensation of warmth and tingling, and you may hear a popping sound. This is completely normal. The galvanic energy works to enlarge your pores for a better application of the treatment.
If your hand does not touch the base electrode ( #8 ) no galvanic energy will be emitted.
Directly afterward, the device will flash a pulse of light onto your skin, and the ready/skin tone warning indicator light (#7) will turn off. You will see a bright flash of light and simultaneously hear a popping sound, which is a normal noise for the device. You will feel a mild sensation of warmth and tingling. The device will immediately recharge for the next pulse.
If you are pulsing, repeat the process. If you are gliding, simply continue. Continue to pulse or glide until you have treated the area fully.
Avoid gaps or overlaps.
The device will only emit repeated pulses when it is in firm contact with your skin, and you keep moving it across your skin.
Stop use immediately, if your skin blisters or burns, if you feel very uncomfortable, or if the device gets too hot.

6.5 After treatment
When you have finished your treatment session:

Long press the control button (#6) to switch off the device. Remember the last energy level setting you used because it will not be restored when you turn the device on again.
Disconnect the adapter from the electricity supply, then clean the device and store it safely (see section 8. Cleaning, maintenance & storage).
After your treatment session, we recommend you apply body lotion to the treated area to help your skin recover from the treatment faster.

Connecting with Bluetooth

The free Silk’n Hair Removal application supports your every step with Silk’n hair removal devices. The app creates your personalized treatment plan, helps you make the safest and most informed choices, and makes sure you follow through the entire course of treatment for best results.
Download the app and follow the registration process and Bluetooth pairing steps. For a free download scan:

http://kaywa.me/s3BST

Cleaning, maintenance & storage

It is important to clean the device after each treatment.

Disconnect the device from the electricity supply.
To clean the device including the treatment surface (#2), wipe with a clean, dry cloth and 70% alcohol. Never use acetone or other abrasive fluids, because they will damage your device.
Use a wipe to dry the device.
After cleaning, we recommend you store the device in its original box.

Troubleshooting

Do not attempt to open or repair your Silk’n device. You may expose yourself to dangerous electrical components or pulsed light energy and cause serious harm to yourself. It will also void your warranty. For unresolved problems or queries, please contact customer service.

Problem	Checks
My device does not start.	Make sure the adapter is properly connected to the

device and that it is plugged into an electrical outlet on the wall.
There is no galvanic pulse when I press the pulse button (#1).| Check that:
• your hand is touching the base electrode (#8) when you press the pulse button (#1).
• the galvanic energy is only active when the galvanic circuit is closed. This is achieved by pressing the pulse button (#1) and the base electrode (#8) at the same time.
There is no light pulse when I press the pulse button (#1).| Check that:
• the green ready/skin tone warning indicator light (#7) is blinking slowly to ensure you have good contact with the skin.
• the treatment surface (#2) is evenly and firmly pressed to the skin. The pulse button (#1) will activate a pulse only if the treatment surface (#2) is firmly pressed against the skin.
If the ready/skin tone warning indicator light (#7) blinks rapidly, this is an indication that your skin tone is too dark for safe use. Try using the device in a different area.
Problem| Checks
---|---
There is no light pulse when the device touches my skin.| Check that the device is connected and the ready/skin tone warning indicator light (#7) is on. Make sure that the treatment surfac e (#2) is evenly and firmly pressed to the skin.
It is also possible that your skin color is too dark.
The ready/skin tone warning indicator light (#7) blinks.| The skin color is too dark.
One or more lights blink continuously.| The device has malfunctioned.
The device has stopped working and is in standby mode.| Press the control button (#6) again to start the device.

Customer service

See our website for more information: www.silkn.eu. This manual is also available as a PDF download from www.silkn.eu. Contact Customer Service to report unexpected operations or events, or any other problem with your device. Our contact details are:

Country	Service number	Email
Belgium	0800-29316

serviceconsommateurbe@silkn.eu
France| 0891-655557| serviceconsommateurfr@silkn.eu
Germany| 089 51 23 44 23| kundenservicede@silkn.eu
Italy| +31 (0)180-330 550| servizioclientiit@silkn.eu
Netherlands| 0900-2502217| klantenservicenl@silkn.eu
Spain| 900 823 302| servicioalcliente@silkn.eu
UK| 0906-2130009| customercareuk@silkn.eu
Other countries| +31 (0)180-330 550| info@silkn.eu

Warranty

Please refer to the separate product warranty booklet for complete information.

The manufacturer accepts no liability for damage or injuries caused by improper or incorrect use.

Disposal

If your device reaches its End of Life stage, be sure to follow your country’s laws for the disposal of electrical items.
Packaging: Dispose of the packaging separated into single type materials. Dispose of cardboard and carton as waste paper and film via the recyclable material collection service.
Device: Do not dispose of household waste! The WEEE directive requires that you dispose of this electrical device (including all accessories and parts) at a designated recycling collection point for electrical devices. This ensures that the device is recycled professionally, and prevents the release of harmful substances* into the environment. Make sure that the device is in an uncharged state before disposal.

Products labeled with Cd = cadmium, Hg = mercury, Pb = lead.

Specifications

Model	H3101
Galvanic	70-400 Microampere (μA)
Spot size	0.9cm x 3cm [2.7cm2]
Technology	Enhanced Home Pulsed Light™
Max energy level	Max 4J/cm2
Wavelength	475-1200nm
Pulse light duration	500-800μs
Mode of operation	Continuous
Repetition rate:	1.0Hz maximum
System weight	225g
Transport & storage between uses and storage condition	Temperature: – 40 to

+70°C
Relative humidity: 10 – 90%rH
Atmospheric pressure: 500 – 1060hPa
Operating conditions| Temperature: 10 – 35°C
Relative humidity: 30 – 75%rH
Atmospheric pressure: 700 – 1060hPa
Time from minimum storage temperature between uses to minimum operating temperature with an ambient temperature of 20°C| 30 minutes
Time from maximum storage temperature between uses to maximum operating temperature with an ambient temperature of 20°C| 30 minutes
Protection against electric shock| Class II medical equipment type BF applied part
Adapter
Input:
Output:| KSAPV0361200300D5
100-240V; 50-60Hz; 0.9A
12Vdc; 3A
Bluetooth LE Operating Frequency:
Transmitter Power:| 2,402 MHz ~ 2,480MHz Below 10 mW/MHz
Pulse parameters (seconds)| Energy level 1: 0.9
Energy level 2: 1.1
Energy level 3: 1.4
Energy level 4: 1.7
Energy level 5: 2.0

Signs & symbols

| Important information about using or maintaining the device.
---|---
| A statement or event that indicates a possible or impending danger, problem, or other unpleasant situation when using the device.
0344| Products marked with this symbol fulfill the requirements of the EU directives.
| Do not dispose of household waste. Dispose in accordance with your country’s laws and help protect the environment. In accordance with the WEEE Directive.
| Follow the instructions for use.
| Degree of protection against electric shock: type BF applied part.
| Keep dry.
| Date of manufacture.
| Manufacturer.
| EU Authorized Representative.
| Product serial number.

**IP30**

| The device is protected against the ingress of objects larger than 2.5 mm diameter, such as fingers, to protect against electric shock.
| Class II. The adapter is protected against electric shock by means of double insulation.

Labeling

Technical results

EMC requirements
IEC 60601-1-2 Edition 4.0 (2014)
The environment of intended uses:
Home Healthcare Facility Environment

Summary of Test Results

Test

| Standard| Class/ Severity level|

Test result

---|---|---|---
Emission (IEC 60601-1-2 section 7)
Radiated emission Freq. range: 30 – 1000 MHz| CISPR 11| Group 1 Class B| Complies
Immunity (IEC 60601-1-2 section 8)
Immunity from Electrostatic discharge (ESD)| IEC 61000-4-2| 8 kV contact discharges & 15 kV air discharges| Complies
Immunity from radiated electromagnetic fields| IEC 61000-4-3| 3.0; 10.0 V/m; 80 MHz ÷ 2.7 GHz, 80% AM, 1 kHz| Complies

Simplified Declaration of Conformity: In accordance with article 10(9) of the EU declaration of conformity, the radio equipment type Bluetooth LE is in compliance with Directive 2014/53/EU.

Legal notice

Copyright 2020 © Home Skinovations Ltd. All rights reserved.
Home Skinovations Ltd reserves the right to make changes to its products or specifications to improve performance, reliability, or manufacturability. Information furnished by Home Skinovations Ltd is believed to be accurate and reliable at the time of publication. However, Home Skinovations Ltd assumes no responsibility for its use. No license is granted by its implication or otherwise under any patent or patent rights of Home Skinovations Ltd. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Home Skinovations Ltd. Data is subject to change without notification. Home Skinovations Ltd has patents and pending patent applications, trademarks, copyrights, or other intellectual property rights covering the subject matter in this document. The furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other intellectual property rights except as expressly provided in any written agreement from Home Skinovations Ltd. Specifications are subject to change without notice. Silken and the Silk’n logo are registered trademarks of Home Skinovations td, Tavor Building, Shaar Yokneam P.O. Box 533, Yokneam 2069206, ISRAEL, www.silkn.com, info@silkn.com.

Manufacturer:
Home Skinovations Ltd, Tavor Building, Shaar Yokneam
P.O.Box 533, Yokneam 2069206, Israel
www.silkn.com
info@silkn.com

EU Authorised Representative:
MedNet EC-REP GmbH
Borkstrasse 10, 48163 Muenster, Germany

Distributor:
Donk 1b, 2991 LE Barendrecht, The Netherlands
www.silkn.eu
Invention Works B.V.
info@silkn.eu

0344