BRESSER CM3000 MyTime LEDsec Wall Clock Instruction Manual

BRESSER CM3000 MyTime LEDsec Wall Clock

ABOUT THIS INSTRUCTION MANUAL

These operating instructions are to be considered a component of the device. Please read the safety instructions and the operating instructions carefully be-fore use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.
This product is intended only for private use.

GENERAL WARNINGS

CHOKING HAZARD!
Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.

RISK of ELECTRIC SHOCK!
This device contains electronic components that operate via a power source (batteries). Children should only use the device under adult supervision. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.

RISK of FIRE/EXPLOSION!
Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the de-vice or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion!
NOTE!

• Do not immerse the unit in water.
• Do not subject the unit to excessive force, shock, dust, extreme temperature or high humidity, which may result in malfunction, shorter electronic life span, damaged batteries and distorted parts.
• Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if it has not been used for a long time.
• The manufacturer is not liable for damage related to improperly installed batteries!

GENERAL INFORMATION

This item is available in the following variants. The functions and technical data are the same. They only differ in its design/in its colour.

• 8020215 CM3000: MyTime LEDsec, black
• 8020215 GYE000: MyTime LEDsec, white
• 8020215 SX9000: MyTime LEDsec, blue
• 8020215 MGU000: MyTime LEDsec, grey
• 8020215 B4K000: MyTime LEDsec, green
• 8020215 URJ000: MyTime LEDsec, purple

SCOPE OF DELIVERY

(Fig. 1)
Wall clock, Instruction manual

Required batteries:
1 x 1.5V battery (Size AA/LR6)

Battery compartment for LEDs:
4 x 1.5V batteries (Size AA/LR6) Batteries not included with purchase.

PARTS OVERVIEW

Wall clock (Fig. 2)

1.  Dial plate
2.  5 seconds display (lights up)
3.  Clock hands (hours, minutes)
4.  Temperature display (indoor)
5.  Motion sensor for temperature display
6.  Wall mount
7.  Battery compartment for the clockwerk
8.  RESET button
9.  REC button
10.  M.SET button
11.  Locking pin
12.  Reset 5-second interval
13.  Battery compartment for the LEDs

GETTING STARTED/POWER SUPPLY

1. Remove the locking pin (11) from the clockwork. The clock can be operated only after the pin has been removed.
2. Insert 1 battery (1.5V, AA/LR6) into the battery compartment (6).
3. Make sure to place the batteries strictly according to the right polarities (+/-) as shown in the battery compartment.

Battery compartment for LEDs:
Insert 4 batteries (1.5V, AA/LR6) into the battery compartment for the LEDs (13).
The wall clock has a light sensor that automatically adjusts the brightness of the LEDs to conserve battery life.

TIME SETTING

NOTE!

• After the clock received the DCF time signal the time will be set according to the Central European time (CET). Summer and winter time change (and reverse) is also set automatically.
• Automatic time setting via DCF time signal
• After inserting the battery the time will be set auto-matically via DCF signal. This process may take a few minutes. During this process the clock hands will turn several times with interruption until they will display the right time.
• Initiate to receive the DCF time signal manually

NOTE!
Use this function when e.g. automatic summer/winter time change does not work or the wall clock temporarely receives no time signal.

1.  Press and hold the REC button (9) for 3 seconds to start manual search for the DCF signal.
2.  The clock hands will move to their start position (12:00 a.m.) and a the wall clock then tries to receive the signal.
3.  Wait approx. 2-5 minutes until the current time will be displayed.

Manual time setting
NOTE!
It is necessary to set the time manually in places where no radio signal is received.

1.  Press and hold the M.SET button (10) for approx. 3 seconds.

2. When the minutes hand starts moving you can the set the time manually:
   • Press the M.SET button shortly to set the time in minutes steps.
   • Press and hold the M.SET button to set the time continously.

3.  Release M.SET button to stop manual setting and save the time automatically and exit manual time set-ting mode.

RESETTING THE 5-SECOND INTERVAL

The 5-second interval can be reset by briefly pressing the key (12). This allows you to synchronise the display of the 5-second interval with the current time. To do this, check the time at e.g. www.timeanddate.com and press the button (12) when the seconds show 00.

MOUNTING/POSITIONING

NOTE!
Make sure you have mounted the device in a safe way. Otherwise the device may fall down and heavy damages can occur for which the manufacturer is not liable.
The wall clock can be mounted on walls with the wall mount (6). The recommended hanging height is 2 me-tres. The detection range of the motion sensor is 125°.
TEMPERATURE DISPLAY / MOTION SENSOR At the bottom of the wall clock is the motion sensor for the temperature display (5). The motion sensor has a range of 2 metres. The temperature is only displayed when the motion sensor is triggered. The Temperature measurement works manually. It may take a few min- utes until the value that is currently measured will be displayed.

TROUBLESHOOTING

Transmission collision
Signals from other household devices, such as door bells, home security systems and entry controls, may in-terfere with those of this product and cause temporarily reception failure. This is normal and does not affect the general performance of the product. The transmission of the radio signal will resume once the interference re-cedes.
Other malfunctions
If there is no response from the wall clock by keystrokes or if any other malfunctions occur perform the following steps.
NOTE!
With this procedure all received data will be deleted.

1.  Press RESET button (8) with a pointed instrument (e.g. pen).
2. The clock hands will move to their start position (12:00 a.m.) and the wall clock then tries to receive the signal.
3. Wait approx. 2-5 minutes until the current time will be displayed.

CLEANING AND MAINTENANCE

Before cleaning the device, disconnect it from the power supply (remove batteries)!
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.

Protect the device from dust and moisture. The batteries should be removed from the unit if it has not been used for a long time.

DISPOSAL
Dispose of the packaging materials properly, ac-cording to their type, such as paper or cardboard. Contact your local waste-disposal service or environ- mental authority for information on the proper disposal.

As per Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.

EC DECLARATION OF CONFORMITY

Hereby, Bresser GmbH declares that the equipment type with part number:

• 8020215 CM3000: MyTime LEDsec, black
• 8020215 GYE000: MyTime LEDsec, white
• 8020215 SX9000: MyTime LEDsec, blue
• 8020215 MGU000: MyTime LEDsec, grey
• 8020215 B4K000: MyTime LEDsec, green
• 8020215 URJ000: MyTime LEDsec, purple

is in compliance with Directive: 2014/30/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.bresser.de info@bresser.de

Bresser GmbH Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de

References

• timeanddate.com
• Bresser | Startseite | Expand Your Horizon mit BRESSER
• timeanddate.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>