GENESIS IN-ACT-KSLNATKON0001 Seaborg 350 Steering Wheel And Pedals Installation Guide

Table of Contents

GENESIS IN-ACT-KSLNATKON0001 Seaborg 350 Steering Wheel And
Pedals

GENESIS IN-ACT-KSLNATKON0001 Seaborg 350 Steering
Wheel And Pedals 3

BUTTON MAP

SWITCH

Before connecting wheel, please enable PRO controller support function in console settings.
Plug wheel USB cable into switch docking station free USB port (with console docked in). Alternatively, using TYPE-C adapter (not included) connect wheel and console directly.
Power-on console.
Wheel will start the automatic configuration of the connection. When it finishes, LED will turn to solid red.
Wheel is ready.

PS3

Plug wheel USB cable into free console USB port.
Power-on console.
Wheel will start the automatic configuration of the connection. When it finishes, LED will turn to solid red.
Wheel is ready.

PS4

Plug wheel USB cable into free console USB port.
Power-on console.
Connect wheel via USB cable* with PS4 controller**. Controller must be turned off. Controller connection is mandatory for wheel to work.
After connection is established, LED indicator will turn to solid red.
Wheel is ready.

Plug wheel USB cable into free console USB port.
Power-on console.
Connect wheel via USB cable with XSX/S/X1/X360 controller. Controller must be turned off. Controller connection is mandatory for wheel to work.
After connection is established, LED indicator will turn to solid red.
Wheel is ready.
- Cable is not included.
- Original controller – although recommended – is not required. However, the producer does not guarantee that every 3rd party replacement will work and/or work correctly.
- A wired controller is required for X360 console.

SWITCHING BETWEEN X-INPUT AND D-INPUT MODES

To switch between X-Input and D-Input modes while wheel is connected to PC, press and hold HOME button for 3 seconds.
Red LED will solid lit after change is done.

WHEEL SENSITIVITY SETUP

Press simultaneously and hold for 3 seconds SHARE and OPTION buttons.
When green LED is lit in center of wheel, release buttons.
Press SHARE again to show current sensitivity level. There are 3 levels: LED is slowly blinking: lowest sensitivity; LED is blinking faster: medium sensitivity; LED is blinking very fast: highest sensitivity.
Press SHARE button again to toggle between sensitivity levels signaled with green LED as described above. When desired sensitivity is chosen, press D-PAD UP to confirm.

Buttons YAXB, LB, LT, RB and RT (BASE buttons) – can be assigned to L-paddle, R-paddle, throttle pedal, brake pedal, gear up, gear down (FUNCTION buttons).
Press simultaneously and hold for 3 seconds SHARE and OPTION buttons.
When green LED is lit in center of wheel, release buttons.
Press desired FUNCTION button, to which other BASE button function will be assigned. Green LED will start blinking.
Press desired BASE button. It’s default function will be now assigned to previously pressed FUNCTION button. Green LED will shut of

PROGRAMMING PEDALS AND PADDLES AS THE Y AXIS

Press simultaneously and hold for 3 seconds SHARE and OPTION buttons.
When green LED is lit in center of wheel, release buttons.
Press LEFT on wheel D-PAD. After green LED is off – pedals are programmed as Y-axis.
Press RIGHT on wheel D-PAD. After green LED is off – gear paddles are programmed as Y-axis.

CLEAR SINGLE BUTTON ASSIGNMENT

Press simultaneously and hold for 3 seconds the SHARE and OPTION buttons.
When the green LED is lit in the center of the wheel, release the buttons.
Press the programmed button once, after LED starts blinking press the same button again.
The default function is restored.

CLEAR ALL BUTTONS ASSIGNMENT

Press simultaneously and hold for 3 seconds the SHARE and OPTIONS buttons.
When the green LED is lit in the center of the wheel, release the buttons.
Press and hold for 4 seconds the OPTIONS button. When LED is off, default functions are restored.
Note: After the device restart, all functions revert to default settings.