Shenzhen Sqt Electronics SMK-668M3AG RF2.4GHz Auto-Link Keyboard and Optical Mouse Instruction Manual
- June 6, 2024
- Shenzhen Sqt Electronics
Table of Contents
Instruction Manual
RF2.4GHz Auto-Link
Keyboard & Optical Mouse
Model: SMK-668M3AG
CAUTION : To use this device properly, please read the user’s guide before installation.
Installing the batteries
The RF2.4GHz Optical mouse use one AA alkaline battery.
The RF2.4GHz Optical keyboard use two AAA alkaline battery.
Installing Batteries in the Mouse
Step 1. Open the battery compartment
Step 2. Insert the batteries as shown inside the battery compartment
Step 3. Replace the cover
Install the batteries in the keyboard
Step1: Remove the battery compartment cover on the bottom of the keyboard by
squeezing the cover in from the tab to release it
Step2:Insert the batteries as shown inside the battery compartment
Step3:Replace the cover
Connecting the Receiver
The receiver is inserted to the USB port immediately, or by an extra USB cable.
Power- Save function:
- Without using the mouse for 1 minute, the mouse will go into sleep mode level1. You can move it to wake up the mouse. The Red LED is still on.
- Without using the mouse for 1-8 minutes, the mouse will go into sleep mode level 2. You can move it to wake up the mouse. The Red LED keep flashing.
- Without using the mouse for more than 8 minutes, the mouse will go into deep sleep mode. The LED turn off automatically.
Multimedia Hotkeys functions:
FN+ESC=F1toF12 key switch is the default the Multimedia or default ofF1toF12
key switch
F1:Previous Track
F2:Play/Pause
F3:Next Track
F4:Mute
F5:Volume Down
F6:Volume Up| F7:Web home
F8:Search
F9:Email
F10:My Favorite
F11: save
F12: computer settings
---|---
Obtain the receiver on the mouse
- If you want to use the mouse,pls take out the receiver (shown in picture ) and connect it to the computer;
- If you want to stop using the mouse, pls store the receiver onto the mouse (shown in picture );
Restoring factory default setting
Mouse:
When the end-user finds the wireless mouse doesn’t work, please check:
- Whether the battery is used out, if yes, please replace it with a new battery;
- If the lead on the mouse bottom is off, please do the following steps to recover the default setting (automatic pairing):
Step one: unplug and plug again the nano receiver onto an available USB port of computer,
Step two: make the wireless mouse close to the nano receiver (within 10 cm), take out the battery and install the battery again inside the Battery compartment, if we find the Led on the mouse bottom on, we can start using the wireless mouse again.
State of standby and wake up the mouse
Without any clicks or scroll movement for 8 minutes, the mouse will go into
standby mode. Click any button or scroll the wheel to wake up the mouse.
Under this economized mode, the optical Red LED will turn of automatically and
the mouse won’t respond by moving it.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
‐‐Reorient or relocate the receiving antenna.
‐‐Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>