ADA INSTRUMENTS А00590 Armo Mini Line Laser User Manual

: June 6, 2024
: ADA INSTRUMENTS

Table of Contents

SPECIFICATIONS FOR ARMO MINI
APPLICATION
FUNCTIONAL CHARACTERISTICS
OPERATION
TO CHECK PLUMB
CARE AND CLEANING
LASER CLASSIFICATION
SAFETY INSTRUCTIONS
WARRANTY
WARRANTY CARD
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OPERATING MANUAL
ARMO MINI / ARMO MINI GREEN
Line laser
adainstruments.com

|
---|---

THE MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES (NOT HAVING AN IMPACT ON THE SPECIFICATIONS) TO THE DESIGN, COMPLETE SET WITHOUT GIVING PRIOR WARNING.

SPECIFICATIONS FOR ARMO MINI

Laser beam ……………………………………………………1H1V
Laser sources ………………………………………………..635nm
Laser class …………………………………………………….Class 2, <1mW
Accuracy………………………………………………………..±3mm/10m
Self-leveling range ……………………………………….±4°
Working range ………………………………………………10 m
Power supply ………………………………………………..2хAA batteries, 1,5V
Tripod thread ……………………………………………….1/4”
Dust/water protection ………………………………… IP54
Operating temperature ………………………………-10°C +40°C
Weight …………………………………………………………..0,267 kg

SPECIFICATIONS FOR ARMO MINI GREEN

Laser beam ……………………………………………………1H1V
Laser sources ………………………………………………..520nm
Laser class …………………………………………………….Class 2, <1mW
Accuracy………………………………………………………..±3mm/10m
Self-leveling range ……………………………………….±4°
Working range ………………………………………………20 m
Power supply ………………………………………………..2хAA batteries, 1,5V
Tripod thread ……………………………………………….1/4”
Dust/water protection ………………………………… IP54
Operating temperature ………………………………-10°C +40°C
Weight …………………………………………………………..0,267 kg

APPLICATION

Line laser ADA ARMO MINI \ ADA ARMO MINI GREEN is designed to check the horizontal and vertical position of the surfaces of the elements of building structures and also to transfer the angle of inclination of the structural part to similar parts during construction and installation works.

FUNCTIONAL CHARACTERISTICS

1 vertical line, 1 horizontal line.
Line laser is designed for indoor use.
Compensator for fast self-leveling works in the range up to ± 4°.
The alarm is activated (laser lines are blinking) when the device deviates from the horizontal plane by ± 4°.
When turning off the power, a built-in locking system can automatically lock the compensator to avoid vibration in the transportation.

1 LASER LINES
2 FEATURES

Horizontal and Vertical laser window
Switch ON handle (compensator lock)
Battery compartment
Screw mount
Magnets
Thread 1/4” features

OPERATION

Open the battery compartment. Insert batteries. Take care to correct po- clarity. Close battery compartment.
Note: Remove batteries, if you are not going to use the line laser for a long period of time.
Place the line laser on the tripod or floor. When using a tripod, place the instrument on the tripod and screw the centering screw into the center hole.
Switch on the line laser setting the handle (2) to the low position. Always set the handle to the up position during transportation. If laser lines begin to blink while switching on the line laser, that means that the line laser is out of range more than ±4°. Level the line laser.
Set the handle (2) to the up position for switching on the line laser.

3 TO CHECK THE ACCURACY OF LINE LASER
To check the accuracy of line laser (slope of plane)
Set up the line laser between two walls, the distance is 5 m. Turn on the line laser and mark the point of the cross laser line on the wall. Turn the line laser by 180º and mark again the point of the cross laser line. Set up the line laser 0,5-0,7m away from the wall and make, as described above, the same marks. If the difference {a1- b2} and {b1-b2} is less then the value of “accuracy” (see specifications), there is no need for calibration.
For example: when you check the accuracy of line Laser the difference is {a1-a2}=5 mm and {b1-b2}=7 mm. The instrument’s error: {b1-b2}{a1-a2}=7-5=2 mm. Now you can compare this error with standard error. If the accuracy of line laser isn’t corresponding with claimed accuracy, contact the authorized service center.

4 TO CHECK THE ACCURACY OF HORIZONTAL BEAM

Choose a wall and set laser 5M away from the wall. Turn on the laser and mark the point of the cross-laser line. Rotate the line laser to shift the beam approximately 2.5m to the left and check that the horizontal line is within the “accuracy” value (see the character- istics) at the same height as the mark indicated by the laser cross. Repeat the same procedure shifting the line laser to the right. Note: do not move the rotating axis when checking the accuracy.

TO CHECK PLUMB

Choose a wall and set laser 5 m away from the wall. Hang a plumb with a length of 2.5 m on the wall. Turn on the laser and make the vertical laser line meet the point of the plumb. The accuracy of the line is in the range if the vertical line doesn’t exceed (up or down) the accuracy that is shown in the specifications (e.g. ±3 mm/10 m). If the accuracy isn’t corresponding with claimed accuracy, contact the authorized service center.

PRODUCT LIFE
The product life of the tool is 7 years. The battery and the tool should never be placed in municipal waste. Date of production, manufacturer’s contact information, country of origin are indicated on the product sticker.

CARE AND CLEANING

Please handle line laser with care.
Clean with a soft cloth only after any use. If necessary damp cloth with some water.
If the line laser is wet clean and dry it carefully.

SPECIFIC REASONS FOR ERRONEOUS MEASURING RESULTS

Measurements through glass or plastic windows;
Dirty laser emitting window;
After line laser has been dropped or hit. Please check the accuracy;
Large fluctuation of temperature: if the instrument will be used in cold areas after it has been stored in warm areas (or the other way round) please wait some minutes before carrying out measurements.

ELECTROMAGNETIC ACCEPTABILITY (EMC)

It cannot be completely excluded that this instrument will disturb other instruments (e.g. navigation systems);
will be disturbed by other instruments (e.g. intensive electromagnetic radiation nearby industrial facilities or radio transmitters).

5 CAUTION STICKER LASER CLASS 2

LASER CLASSIFICATION

The line laser is a laser class 2 laser product according to DIN IEC 608251:2014 and Class II.

SAFETY INSTRUCTIONS

Please follow up on the instructions given in the operators’ manual.
Do not stare into the beam. The laser beam can lead to an eye injury (even from greater distances).
Do not aim the laser beam at persons or animals. The laser plane should be set up above the eye level of persons. Use the instrument for measuring jobs only.
Do not open instrument housing. Repairs should be carried out by authorized workshops only. Please contact your local dealer.
Do not remove warning labels or safety instructions.
Keep instruments away from children.
Do not use instruments in an explosive environment.

WARRANTY

This product is warranted by the manufacturer to the original purchaser to be free from defects in material and workmanship under normal use for a period of two (2) years from the date of purchase. During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar model at manufactures option), without charge for either part of labor. In case of a defect please contact the dealer where you originally purchased this product. The warranty will not apply to this product if it has been misused, abused, or altered. Without limiting the foregoing, leakage of the battery, bending, or dropping the unit are presumed to be defects resulting from misuse or abuse.

WARRANTY DOESN’T EXTEND TO THE FOLLOWING CASES:

If the standard or serial product number will be changed, erased, removed, or will be unreadable.
Periodic maintenance, repair or changing parts as a result of their normal runout.
All adaptations and modifications with the purpose of improvement and expansion of the normal sphere of product application, mentioned in the service instruction, without the tentative written agreement of the expert provider.
Service by anyone other than an authorized service center.
Damage to products or parts caused by misuse, including, without limitation, misapplication or negligence of the terms of service instruction.
Power supply units, chargers, accessories, wearing parts.
Products, damaged from mishandling, faulty adjustment, maintenance with low-quality and non-standard materials, presence of any liquids and foreign objects inside the product.
Acts of God and/or actions of third persons.
In case of unwarranted repair till the end of the warranty period because of damages during the operation of the product, its transportation, and storing, the warranty doesn’t resume.

WARRANTY CARD

Name and model of the product __
Serial number___Date of sale__
Name of commercial organization ____
stamp of commercial organization

The warranty period for the instrument exploitation is 24 months after the date of the original retail purchase.
During this warranty period, the owner of the product has the right to free repair of his instrument in case of manufacturing defects. Warranty is valid only with original warranty card, fully and clear filled (stamp or mark of the seller is obligatory). Technical examination of instruments for fault identification which is under the warranty, is made only in the authorized service center. In no event shall the manufacturer be liable before the client for direct or consequential damages, loss of profit, or any other damage which occurs as a result of the instrument outage. The product is received in the state of operability, without any visible damages, in full completeness. It is tested in my presence. I have no complaints about the product quality. I am familiar with the conditions of warranty service and I agree.

purchaser signature ___

Before operating you should read service instructions!
If you have any questions about the warranty service and technical support contact seller of this product

ADA International Group Ltd., No.6 Building, Hanjiang West Road #128,
Changzhou New District, Jiangsu, China
Made In China
adainstruments.com