TECTRONPRO J300 Portable Power Station User Manual

TECTRONPRO J300 Portable Power Station

GENERAL SPECIFICATIONS

The J300 is a portable battery pack with the ability to supply 300W of pure sine-wave AC power via the onboard AC output. Additionally, The J300 is able to support USB quick charging via the onboard 2 x USB-PD port and 2 x USB-A ports. Overall storage capacity is 307.84Wh / 269.36Wh of energy.

WARNINGS

To ensure safe operation and service of the meter, follow these instructions. Failure to observe these warnings can result in severe injury or death.

• DO NOT use J300 in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons, even though we have built-in overload protection.
• DO NOT use J300 or AC Wall plug power adapter, if it is damaged or has been modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• DO NOT subject to vibration, impacts, or drops. Secure J300 during transport. The housing may not show signs of damage, but internal componerts may have been compromised. It is adviseable to replace it if any such severe events occur.
• DO NOT expose J300 to moisture, rain, or snow.
• DO NOT charge, use or store J300 in a bathroom or in an area exposed to rain or moisture.
• DO NOT leave children or persons, with reduced physical/sensory or mental capabilities/or lack of experience and knowledge, along with J300 unless they have been given supervision or instruction concerning use of it by a person responsible for their safety.
• DO NOT attempt to repair J300 or AC Wall plug power adapter. There are no user-serviceable components inside.
• DO NOT handle J300 with wet hands.
• DO NOT place J300 on its side or upside down while in use or in storage.
• If rust, odor, overheating, or other abnormal circumstances are observed, stop using and contact customer service.
• Children should be supervised to ensure that they DO NOT play with the J300 alone.
• The J300 is only used for emergency power station, it cannot replace the standard AC or DC power of household appliances or digital products.
• Keep away from high voltage electrical fields.
• Risk of fire and burns, DO NOT open, crush, heat above 113°F (45°C) or incinerate. Follow all instructions.
• Use of a power supply, charger, or cable not recommended or sold by portable battery manufacturers may result in a risk of fire or injury to persons.
• Should fluid from inside of J300 come in contact with your skin or clothing, wash the affected areas with tap water.
• The accessories included in the box should only be used with the J300.
• KEEP THIS PRODUCT AWAY FROM PETS.

FEATURE DETAILS

1. LCD Screen Display
2. DC Output
3. Cigarette Lighter Output
4. USB-A Output
5. USB-PD Output
6. DC Input/Car Charging Input
7. PV Input
8. SOS MODE
9. Anti-collision Strip
10. Folding Handle
11. Wireless Charger
12. Air Intake Vent with Cooling Fan
13. ED LIGHT
14. 300W Rated AC Outputs
15. EU
16. US
17. SAU
18. SA pins

Note: No user-serviceable parts inside. Recommended to fully charge the J300 before use.

BUTTON FEATURE

• DC Outputs Power ON/OFF Button
• J300 Power ON/OFF Button
• LED light Button
• USB Outputs Power ON/OFF Button
• AC Outputs Power ON/OFF Button
• SOS mode

LCD FEATURES

• Battery Level Indicator
• Input Status
• LED ON
• FANON
• Error Code
• DC Outputs Status
• AC Outputs Status
• USB Outputs Status

HOW TO CHARGE

DO NOT CONNECT THE DEVICE VIA AC OUTPUT PORT WHILE CHARGING THE J300. RECOMMEND TO DISCONNECT THE J300 WHEN FULLY CHARGED.

WHAT IT POWERS

FUNCTION BUTTONS

J300 Power ON/OFF Button B

Button B is the master switch. Press Button B to activate the button A/D/E. Press Button B to shut down the output(s) When not in use.

SOS MODE F & LED LIGHT C

• Function available no matter the Button B activate or not.
• First, press Button C/F to turn on the LED light;
• Second, click to open the flash mode;
• Third, click to open SOS mode;
• Fourth, click Button C/F again to turn off the LED.

DC OUTPUTS POWER ON/OFF A

The DC output ports will NOT function until the appropriate Button B & A are both pressed to activate. Press Button A to shut down the output(s) When not in use.

USB OUTPUTS POWER ON/OFF D

The USB output ports will NOT function until the appropriate Button B & D are both pressed to activate. Press Button D to shut down the output(s) when not in use.

AC OUTPUTS POWER ON/OFF E

The AC outlets will NOT function until the appropriate Button B & E are both pressed to activate. Press Button E to shut down the output(s) when not in use.

WIRELESS CHARGER

Press ON/OFF Button B before charging. Press ON/OFF Button B to shut down the output(s) when not in use.

COOLING FAN

J300 utilizes an internal cooling fan to ensure the product is operating within the appropriate temperature range. J300, when it experiences a higher output load, will automatically turn on the fan. During discharge, and possibly charging, the fan may operate intermittently to keep the internal temperature within operating range. The fan will likely start when the AC circuit is activated to ensure proper operation.

DETAILS DISPLAYED ON LCD

LCD display information: battery power, input power, AC output power, DC output power, USB output power.

1. After the charger is inserted into the DC charging port, the power is displayed on the left side of the screen, the running light and the power are displayed, and the screen “input” is on and the charging power is displayed;
2. After the DC circuit is opened, the “DC on” of the display screen lights up and displays the output power;
3. After the USB circuit is turned on, the “USB on” of the display screen lights up and displays the output power;
4. After the AC circuit is turned on, the “AC on” of the display screen lights up and displays the output power;
5. The main control IC detects that the function is abnormal, will protect itself immediately, and the display screen displays the fault code:
6. W01: battery high-temperature protection
7. W02: battery low-temperature protection
8. W03: AC short circuit protection
9. W04: overload protection
10. W05: low voltage protection

LCD Screen will enter sleep mode after 20 seconds of inactivity (no new output load detected), and will “wake up” when inputting a charging cord or when any button is pressed.

OPERATING INSTRUCTIONS

CHARGING J300

Connect the provided AC Wall power adapter to Input@, and allow J300 to fully charge prior to use, approx. 5-6 hours. Connect the Anderson plug to the Input 0, and allow J300 to fully charge prior to use, approx. 6-9 hours with the Solar Panel. Noted that the red part of the Anderson plug is positive, and the black part is negative. Please connect positive to positive and negative to negative to ensure using correctly. When charging, the LCD ScreenG)will be illuminated, and the LCD display will provide Battery level Indicator H, J300 is fully charged when the level is 100%. It is recommended to fully charge it every 3 months to maintain the health of the battery pack.

POWERING / CHARGING DEVICES WITH J300

Select the type of outlet required by pressing the Output ON/OFF Button A/D/E. The output port will NOT function until the appropriate button is pressed to activate the port.

Press the ON/OFF button(s) to shut down the output(s) when not in use

PASS-THROUGH SHARGltbG

Thu advanced battery management system of the j300 allows it to charge a connected device via DC outputs & USB outputs while charging the J300. DO NOT CONNECTED DEVICE VIA AC OUTPUTS WHILE CHARGE THE J300.

Overload Condition

If an overload condition occurs on the OUTPUT ports, J300 will:

• Automatically turn off AC Outlets 14 power.
• The blue indicator light of LCD screen 1 still illuminated.
• DC Outputs Status M still the same status as usual.

Do following:

• Check the input charge cable. The port will be efficient when the input charge cable meets the specification outlined in the GENERAL SPECIFICATIONS section.
• Only charge J300 with provided AC wall power adapter.

J300 ACCESSORY LIST

• 18V with MC4 connector cable
• 110 ~ 240V special adapter
• 12V Car Charger cable
• User Manual

Recommend to use 120W Solar panel (not included).

CLEANING

Be sure that J300 is disconnected from all input power sources and output devices. Use a clean, dry, soft lint-free cloth to wipe down it. Remove any debris, dirt, or other blockages on both side vents. When cleaning debris from the side vents, do not allow the debris, dirt, or other blockages to enter the body of J300.

• DO NOT use abrasive cleaners or solvents.
• DO NOT use compressed air to clean side cooling vents, as this will force foreign particles into the internal circuitry.

To avoid the risk of electrical shock, DO NOT use metal objects to clean ports.

STORAGE

If storing for more than 1 month, charge completely before storage and recharge approximately every 3 months to avoid full discharge and possible damage. Store indoors, in cool temperatures, mild humidity, and away from direct sunlight (See GENERAL SPECIFICATIONS section). Leaving in a vehicle or other confined spaces in extreme hot temperatures can lead to decreased service life, overheating, and fire. Extreme cold conditions below specific storage range can also harm J300 performance and service life. Keep away from corrosion chemicals and gases. After taking out of storage, visually inspect to make sure J300 and all accessories look satisfactory. This increase review the intake and exhaust side vents to ensure they are clear of debris. Allow J300 to return to ambient conditions before recharging, or charging other devices.

ATTENTION

Transportation:

J300 complies with all legal requirements for the transport of dangerous goods. The capacity of the lithium battery pack exceeds 1 00Wh. Based on international standards, if J300 is transported by airplane, it must be transported in accordance with IATA standard packaging. IATA instructions and labeling requirements and the relevant declarations must be completed.

• Not permitted on aircrafts
• To recharge preserve at the least once battery every lifespans, 3 months
• Use original or cerified charger and cables
• Avoid extreme temperature
• Avoid dropping
• Do not disassemble
• It’s not waterproof,do not expose to liquids
• Please dispose of batteries and electronic goods in accordance with local regulations

TROUBLESHOOTING

J300 WILL NOT CHARGE OR OPERATE connected devices:

• Ensure that the DC/USB/AC Output Ports@/@!@!@!@ are activated by pressing the Button(s) B & A/D/E for the port(s) in use.
• Confirm the connected device is suitable for the J300 by reviewing the output specifications provided in the GENERAL SPECIFICATIONS section.
• Confirm J300 is charged by reviewing the Battery Level Indicator H.
• Verify the watt data displayed on the Status Indicator 1/J/K/L of LCD Screen G) for overload condition.

J300 WILL NOT CHARGE:

• Confirm that the wall plug power adapter’s cord is inserted fully into the DC Input@
• Confirm that the AC wall plug power adapter is the charger provided with J300.
• If the input does not comply with the requirements located in the GENERAL SPECIFICATIONS section, the Low Watt range Oto 10 may be displayed on
  Input Status I of LCD screen 1.

MAINTENANCE

Recharge as needed. There are no pre-designated intervals at which to recharge as long as the J300 is being used regularly. Avoid discharging completed on a regular basis, as this can impact overall life.
Regularly inspect all ports and wall charger for any debris, dirt, damage and corrosion.

• DO NOT attempt to fix.
• DO NOT cover the J300 with towels, clothing or other items. Regularly observe if the side vents are collecting dirt or dust, and clean following cleaning procedures noted in manual.

DISPOSAL/RECYCLE

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations.

WARRANTY

• Do not put the product in water.
• Do not heat the product or get close to the fire source!Do not disassemble or transform the product without authorization!Do not hit the product hard.
• It is forbidden to use or place the battery under high temperature (hot sunshine or very hot car), otherwise it may cause overheating, fire, function failure and short service life of the battery.
• Do not disassemble the battery.
• Do not short circuit the battery.
• Do not use a non dedicated charger to charge the battery, which will cause danger.
• Do not directly touch the leaking battery. The leaking electrolyte will cause skin discomfort. In case the electrolyte enters the eyes, rinse it with clean water as soon as possible, do not rub the eyes, and send it to the hospital for treatment quickly.
• If the battery has been stored for more than three months, the customer is requested to charge and discharge the product once with a charger within the specified parameter range.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>