LOFTEK Submersible LED Light with Magnet Suction Cup RF Remote User Manual

LOFTEK Submersible LED Light with Magnet Suction Cup RF Remote

Features

• Size Oia.8.6″3.SCM
• LED 15 LED s
• Color RGB (16 Colors)
• Increase Magnets.Suction Cups,3 Timer Options
• Dynamic Mode Flash,Fade,Smooth
• Light Battery 3xAA(Not included)
• Remote Battery 1x CR2025 Button Cell (Included)
• Light Battery Life
• 30-70 Hours(Depends on the batteries
• and display mode)
• Remote Battery Life 3-6Months
• Max Remote Range 164FT/50M(ln Air), 10FT/2M(ln Water)

Tips for Battery

1. Please prepare 3pcs good quality AA batteries. otherwise will influence the brightness and using time.
2. fJ Press the button”®” to check if all LED bulbs are showing white color, whichever brightness is darker,it means the light batteries are in low power,lower power will weaken the sensitivity of remote. If the light keeps flashing red light, it means the batteries will be out of power soon, Please change new batteries.
3. D If you don·t use for a long time. Please remove the batteries.it will help to save power and protect the lights.

Tips for Magnets

1. Magnet is perfect for any iron place which can be attracted by the magnet. especially rough vertical surface.but not for smooth vertical surface,please use a suction cup instead.
2.  Magnet is a strong magnet, but it better to use on pure iron surface,alloy will reduce the absorb effect.

RF Remote

Tips for Suction Cups

1. the suction cup can be used in both air and underwater on flat and smooth surfaces. But don’t work on a rough surface.
2. Please clean the surface before attaching. make sure there is no stuff between the surface and suction cups. Especially,clean all the lubricant which may come from shower creammoss in the swimming pool etc. Any lubricant will defeat it, So cleaning the surface is very important before attaching suction cups.
3. Please pull the suction cups vertically if you want to remove them, don·t pull it horizontally,it may pull out from the hole, this is the feature of the design. Please note, and use it the incorrect way.

Tips for Waterproof

1. Please make sure the sealing ring is in the grooves.
2. Please try your best to screw up until the cap can not be twisted any further, to make it fully waterproof before putting it into water.
3. It’s better not use in hot water, because the vapour may go into the light, ii will damage the components and lead to stop working.
4. When you change batteries, please wipe off the water in the light, to keep the batteries case dry.

Tips for Remote Control

1. Please remove the plastic insulating film on the bottom of the remote before using ii.
2. Please keep the remote dry from water, because it’s not waterproof, water will make it stop worting.
3. Please press and hold the button “@) ” for 2 seconds to activate the light before setting, to make all lights light up together. Press longer if some lights don’t respond on time.
4. Because water will largely adsorb signals, so our lights support to remote max 1 Oft/ 2m underwater, please use remote within 164ft/50m in air.

Tips for Timer Options

1. 2H——————————————-@)
   Press this button, the white light will flash twice, ii means 2 hours on, 22 hours off, circled by 24 hours, until the light batteries power off.

2. 4H / 6H——————————— @)@)
   4H:4 hours on, 20 hours off (white light will flash 4 times)
   6H:6 hours on, 18 hours off (white light will flash 6 times)

3. D TIME OFF——————————— @)
   Turn off the timer, the light will keep on until the light batteries power off.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>