H Koenig WMG800 Professional Electric Meat Grinder Instruction Manual

H Koenig WMG800 Professional Electric Meat Grinde

DESCRIPTION

1.  Hopper plate
2.  Body
3.  Fasten button
4.  Switch panel
5.  Switch knob
6.  Kibbe attachment
7.  Head inlet
8.  Sausage attachment(block)
9.  Sausage attachment(fine)
10.  Sausage attachment(medium)
11.  Sausage attachment(large)
12.  Food pusher
13.  Head
14.  Snake
15. Cutting plate(fine)
16.  Cutting plate(medium)
17.  Fixing ring
18. Cutting plate(large)
19. Cutting blade

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including the following:

•  It is for household use； Do not use outdoors.
•  Unplug from outlet while not in use, before putting on or taking off parts, and before cleaning.
•  Unplug when assembling and disassembling the unit.
•  Close supervision is necessary when any appliance is used near children.
•  When carrying the unit be sure to hold the body with both hands. Do not carry the unit by the hopper plate or head.
•  Do not fix the cutting blade and cutting plate when using kibbe attachment.
•  Never push products by hand. Use food pusher.
•  Do not grind hard food such as bones, nuts, etc.
•  Do not grind ginger and other materials with hard fiber.
•  Continuous running of meat grinder should be not more than 10 minutes with the following 10 minutes interval for motor cooling.
•  Operate the unit from “Ⅰ” & “Ⅱ” to “R” or from “R” to “Ⅰ” & “Ⅱ”after the previous working condition stops more than 30 seconds, or it may cause some abnormal case such as moving up and down and easily destroy the unit.
•  To avoid jamming, do not force to operate the unit with excessive pressure.
•  When the circuit breaker activates, do not switch on.
•  Never try to replace the parts and repair the unit by yourself.
• Do not immerse cord or the body of mixer into water as this would give rise to electric shock.
• This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety
•  Children should be supervised to ensure that they do not play with the appliance.
•  Do not operate this appliance if the cord or plug is damaged. Return it to the store of service or repair by professional serviceman.
•  To avoid electric shock, be careful not to get the motor unit, power cord or plug wet.
•  Never use an accessory that is not suitable for this device
•  This appliance is not intended for unsupervised use by young children or infirm persons.
•  Never put your hands near moving parts. Never insert fingers into the chimney, always use the food pusher.
•  Do not use the unit with frozen food. Allow food to thaw completely before using the chopper.
•  Always place the unit on a flat, dry and stable surface.
•  Do not operate this appliance if it has a damaged cord or plug, if it is not working properly or if it has been damaged or dropped. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
•  Always turn off and unplug the unit to release any food stuck on the blades or auger.
•  This appliance may be used by children of at least 8 years of age, as long as they are supervised and have been given instructions about using the appliance safely and are fully aware of the dangers involved.
•  Cleaning and maintenance should not be carried out by children unless they are at least 8 years of age and are supervised by an adult.
•  Keep the appliance and its power cord out of reach of children under 8 years of age.
•  When using electrical equipment, safety precautions must always be taken to prevent the risk of fire, electric shock and/or injury in the event of misuse.
•  Make sure that the voltage rating on the typeplate corresponds to your main voltage of your installation. If this is not the case, contact the dealer and do not connect the unit
•  Never leave the unit unattended while in operation.
•  The device must not be used if it has been dropped, it obvious signs of damage are visible

FOR THE FIRST TIME

•  Check that voltage indicated on the rating label corresponds the mains voltage in your home.
•  Wash other parts except body (motor housing) in warm soapy water.
•  Wash all parts (except body) in warm soapy water.
•  Before plug in, make sure the key switch in the “OFF” position, that is the natural state of all keys.

INSTRUCTION FOR USE

ASSEMBLING
hold the head and insert it into the inlet(when inserting pls pay attention the head must be slanted as per arrow

indicated on the top, see fig.1), then move the head anticlockwise so that the head being fastened tightly . (fig.2)

•  Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into the motor housing (fig.3).
•  Place the cutting blade onto the snake shaft with the blade facing the front as illustrated (fig.4).If it is not fitted properly, meat will not be grinded.
•  Place the desired cutting plate next to the cutting blade, fitting protrusions in the slot (fig.5).
•  Support or press the centre of the cutting plate with one finger then screw the fixing ring tight with another hand (fig.6). Do not over tighten.
•  Place the hopper plate on the head and fix it into position.
•  Locate the unit on a firm place.
•  The air passage at the bottom and the side of the motor housing should be kept free and not blocked.

MINCING MEAT

•  Cut all foods into pieces (Sinewless, boneless and fatless meat is recommended, approximate size :20 mm x 20 mm x 60 mm) so that they fit easily into the hopper opening.
•  Sausage, torsion will switch to “Ⅰ” & “Ⅱ” position, ground meat..
•  Feed foods into the hopper plate. Use for it only the food pusher (fig.7)
•  After use, the switch to “O” and stop device, and then pull plug.

Reversal function
After unblocking, release“R” ,and pull plug out, then clean food out from head of appliance.

MAKING SAUSAGE
Before starting please assemble sausage attachment as per following (fig.11)

CLEANING AND MAINTENACE

DISASSEMBLING

•  Make sure that the motor has stopped completely.
•  Disconnect the plug from the power outlet.
•  Disassemble by reversing the steps from 1-6 pictures.
•  To remove the cutting plate easily, place a screwdriver between the cutting plate and the head as illustrated and lift it up (fig.12).
•  Press the fasten knob move the head as per direction illustrated on fig 13,then you can take out the head.

CLEANING

•  Make sure that the motor has stopped completely.
•  Disconnect the plug from the power outlet.
•  Remove meat, etc. Wash each part in warm soapy water.
•  A bleaching solution containing chlorine will discolor aluminum surfaces.
•  Do not immerse the motor housing in water, but only wipe it with a damp cloth.
•  Thinners and petrol will crack or change the color of the unit.
•  Wipe all the cutting parts by vegetable oil -wet cloth.

SPECIFICTION

Product guarantee:
The warranty is valid from the date of purchase (invoice or sales receipt as proof). This warranty does not cover defects or damage resulting from improper installation, improper use, or normal wear and tear of the product.

DISPOSAL
Do not dispose of this product as it has with other household products. There is a separation of this waste product into communities, you will need to inform your local authorities about the places where you can return this product. In fact, electrical and electronic products contain hazardous substances that have harmful effects on the environment or human health and should be recycled. The symbol here indicates that electrical and electronic equipment should be chosen carefully, a wheeled waste container is marked with a cross.

Adeva SAS / H.Koenig Europe – 8 rue Marc Seguin – 77290 Mitry Mory – France www.hkoenig.com – sav@hkoenig.com – contact@hkoenig.com – Tél: +33 1 64 67 00 05

References

• H.Koenig : Le spécialiste du petit électroménager

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>