dyson 419900-01 Autoreact Cool Autoreact Purifier User Manual

dyson 419900-01 Autoreact Cool Autoreact Purifier User Manual

Assembling your machine

Use both hands to lift your machine out of the box, by its base. Do not lift out by the loop amplifier. Assemble your machine with the filters that are supplied. Dyson Purifier Cool Auto React Supplied with a HEPA + Carbon filter. Push your HEPA + Carbon filter into the outer cover and position onto the base. Push firmly until both outer covers click securely into place.

Dyson Purifier Cool Auto React Supplied with separate HEPA and carbon filters. Push the carbon filters into place on the machine. Push the HEPA filter into the outer cover. Put the outer covers into position on the base and push firmly until they both click securely into place.

Getting started

The layout of the remote control with the power button on the top left, the airflow speed toggle button in the middle left and the oscillation button on the bottom left. On the top right-hand side is the Information menu button, then going downwards is the Auto mode button, Airflow direction and then the Night mode button at the bottom.

Power and continuous monitoring

Stand-by on/off Press the Standby on/off button on your Dyson purifying fan or remote control to stop your machine. It will continue to monitor the air quality.

Continuous monitoring Continuous monitoring is turned off by default. Once turned on, it will always be active until you turn it off again.
With continuous monitoring turned on, your Dyson purifying fan will gather air quality, temperature and humidity information, which is displayed on the LCD screen.

Continuous monitoring Press and hold the Auto mode button on the remote control for 5 seconds to turn it on. The LCD screen will indicate when continuous monitoring is on or off.

Information menu

Press this button to scroll through the information being monitored by your Dyson purifying fan. Information about air quality, temperature, humidity and filter levels is shown on the LCD screen. When a particular type of pollutant causes air quality to decrease, a symbol for the pollutant will show on the LCD screen.

Auto mode

Set your Dyson purifying fan to Auto mode and the on-board sensors will intelligently adjust the settings of the machine according to the air quality. Air quality: your machine will pause when the target air quality has been reached, switching on again when the air quality levels drop. Airflow speed: the airflow speed will increase until the target air quality and temperature have been reached.

Airflow speed and direction

Press the Airflow speed button to increase and decrease the airflow speed. Press the Airflow direction button to change the direction of airflow from front to back. Change the airflow direction for your personal comfort. Select the Airflow direction to Fan mode for airflow from the front for purifying and cooling.

Oscillation

Press the Oscillation button to circulate the air around the room and scroll through the oscillation settings from 0° to 350°.

Night mode and Sleep timer

In Night mode, your Dyson purifying fan will continue to monitor and respond to changes in air quality, but only using its quietest settings ­ and with its LCD screen dimmed. Press the Night mode and Sleep timer button to scroll through the timer options.

Changing your HEPA + Carbon filter

Before changing your filter, switch off and unplug your Dyson purifying fan. The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the Information button on your remote. You’ll need to reset the filter life on your machine.

Dyson Purifier Cool Auto React
Supplied with a HEPA + Carbon filter. To change your HEPA + Carbon filter, push down on the buttons either side of your machine to release the outer cover. Push down on the tabs to remove the filter. Push the replacement filter into the outer cover and make sure the tabs click into place. Put the outer covers into position on your machine and push firmly until they both click securely into position. Plug in and switch your machine, and reset your filter life.

Resetting your HEPA + Carbon filter life

It’s important to reset your filter life after you have replaced your filter.

Resetting your HEPA+Carbon filter life
Press and hold the Night mode button on your remote control.

The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Changing your HEPA and carbon filters

Before changing your filter, switch off and unplug your Dyson purifying fan. The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the Information button on your remote. You’ll need to reset the filter life on your machine.

Dyson Purifier Cool Auto React
Supplied with separate HEPA and carbon filters.
To change your HEPA filter, push down on the buttons either side of your machine to release the filter covers. Push down on the tabs to remove the HEPA filter.
Push the replacement filter into the outer cover and make sure the tabs click into place.
To change the carbon filter from your machine, remove the filter from the base of your machine and insert the replacement filter.
Put the outer covers into position on your machine and push firmly until they both click securely into position.
Plug in and switch your machine, and reset your filter life.

Resetting your HEPA and carbon filter life

It’s important to reset your filter life after you have replaced your filter.

Resetting your HEPA filter life
Press and hold the Night mode button on your remote control.

The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Resetting your carbon filter life Press and hold the Oscillation button on your remote control.

The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Looking after your machine

To always get the best performance from your Dyson purifying fan, it’s important to regularly clean it and check for blockages.

Cleaning your machine If your machine is dusty, wipe with a damp lint- free cloth. Look for blockages in the air inlet holes on the filter and the small aperture inside the loop amplifier. Use a soft brush to remove dust and debris. Don’t use detergents or polishes to clean your machine.

Error codes If your machine shows an error code, try turning it off and then on again. If this doesn’t clear the error code contact Dyson Customer Care. For more information and support for your machine go online: www.dyson.com/support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>