biamp Vidi 250 Wide Angle 4K Conferencing Camera User Guide
- June 6, 2024
- biamp
Table of Contents
biamp Vidi 250 Wide Angle 4K Conferencing Camera User Guide
PRODUCT DESCRIPTION
The Vidi 250 is a wide angle 4K camera designed for use with video conferencing systems. Intended for use in Huddle, small or medium conferencing rooms, the Vidi 250 has a 120° field of view, allowing everyone in the room to be seen. The Vidi 250 uses auto framing technology to adjust the focus and zoom to keep participants in view. The Vidi 250 can be either display mounted or wall mounted.
FEATURES
- LED indications for camera activity
- 4K, wide angle 120° field of view
- Pan/Tilt/Zoom with 5x digital zoom
- Auto framing technology keeps participants in frame
- Multi-microphone array
- Privacy cover
- Above and below display mounts included
- Display side and wall mount options
- Optional camera control software for manual control
CAMERA INSTALLATION
Top Mount: (attached to the camera)
- Pull the lower arm of the mount down.
- Position the mount onto the top of the display and push the lower arm against the back of the device to secure.
- Plug the USB cord into the back of the camera.
- Remove the privacy cover and aim the camera.
- Optional – Install Camera Control App for manual control.
Under-Display Plate: (included)
You must download the Camera Control App to control image orientation when mounting the camera under the display.
- Adhere the adhesive plate to the underside of the TV or monitor. To ensure proper adhesion, properly clean the mounting surface and apply pressure to the mount for 30 seconds. If possible, wait 24 hours before mounting the camera to ensure maximum bond.
- Turn the camera and mount upside down and push the top mount into the under-display plate clips as shown. The camera/mount will be able to move forward and backward slightly.
- Plug the USB cord into the back of the camera.
- Remove the privacy cover and aim the camera.
- In the Camera Control app you must choose the “Flip” option to change the view orientation during setup.
Side Mount Accessory (VMA 200-DM) typical installation:
- Open the side clamps and position on the back or side of a TV or monitor, so the arm can position the camera beside the display. To ensure proper adhesion, properly clean and dry the mounting surface. Uncover the adhesive strips and attach mount to the display. Apply pressure to the mounts for 30 seconds. If possible, wait 24 hours before attaching the camera to ensure maximum bond.
- Remove the camera from the top mount and screw it onto the side mount until tight. Keep the privacy cover on.
- Plug the USB cord into the back of the camera.
- Remove the privacy cover and carefully move/rotate the arm and camera to point to the desired location.
- Optional – Install Camera Control App for manual control.
Wall Mount Accessory (VMA 200-WM) installation:
Position the wall mount on a vertical surface (wall or furniture) close to the TV or monitor and mark the hole locations. Prepare the surface or pre-drill the holes as necessary.
- Attach the mount to the surface (shown with screw / anchors).
- Remove the camera from the top mount and screw the camera onto the mount until tight.
- Plug the USB cord into the back of the camera.
- Remove the privacy cover and carefully move the camera to point to the desired location.
Biamp Camera Controller software (App)
The Biamp Camera Controller provides manual control of Biamp conferencing cameras. This software, available on both PC and Mac, is available <here> This software will detect a connected camera and provide a preview window with additional controls.
Software features:
- Preset saving and recall (x3)
- Manual zoom and panning (ePTZ)
- Auto framing enablement
- Image mirroring
- Image flip for under-display mounting
The camera control software is also used to update the device firmware. The firmware update screen can be accessed by selecting “about” from the camera controller application icon. Firmware is available <here>
Software features:
- Preset saving and recall (x3)
- Manual zoom and panning (ePTZ)
- Auto framing enablement
- Image mirroring
- Image flip for under-display mounting
Maintenance
- Clean the camera lens with a soft non-abrasive cloth
- The mounting ball can be tightened if necessary
Top mount
- Remove mount from video display, and pull ring down.
- Rotate to tighten the ball and place camera back on the display.
CONTACT US
Email : support@biamp.com
Web : support.biamp.com
Warranty : biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
References
- Biamp-Downloads
- Warranty
- Home - Biamp Cornerstone
- Biamp - Connecting People Through Extraordinary Audiovisual Experiences