N 100 Network Expander For Biamp USB Device User Guide
- May 15, 2024
- biamp
Table of Contents
N 100 Network Expander For Biamp USB Device
Product Information
Specifications
- Product Name: N 100TM Network Expander
- Manufacturer: Biamp
- Power Supply: 24V/3.75A
- Front Panel Indicators: Off when not powered, Green when powered, Red when booting
- Ports/Terminals: USB Input Type-B, USB 3.0 Type-A, USB 3.0 Type-C, RJ45 Network Gigabit Ethernet (LAN)
FAQ
- How can I access the Web Administrator Console for managing N 100 settings?
- To access the Web Administrator Console, visit the provided link in a web browser.
- Where can I find support, warranty information, and safety/compliance details?
- You can visit the Biamp website for support at support.biamp.com, email support@biamp.com for assistance, check warranty information at biamp.com/legal/warranty-information, and find safety and compliance details at biamp.com/compliance.
INSTALLATION CONSIDERATIONS
- The N 100 is designed to be installed behind a display or close to the in-room display.
- The device can also be securely mounted in various locations using the provided mounting plate, including desktops, walls, and more. The plate has a built-in cable management retainer cord organization and security.
- Do not exceed the maximum ambient operating temperature of 32-104° F (0-40° C). Be aware of conditions in an enclosed rack that may cause the temperature to exceed ambient room conditions.
Warning: the N 100 power supply MUST NOT be connected to a VBC 2500 or ABC 2500 conference bar. the unit will be damaged.
INCLUDED IN THE BOX
IN THE BOX
- N 100
- Cable management cover
- Mounting plate
- Wall screws (4)
- Wall anchors (4)
- Mounting-plate screws (4)
- Cover screw (1)
- USB 3.0 3’ (1m) Type A to B (1)
- Power supply
- QR-code sheet & safety manual (not shown)
DEVICE LAYOUT
FRONT PANEL
FRONT PANEL INDICATORS
- Off:
- The device is not powered
- Green:
- The device is powered
- Red:
- The device is booting.
REAR PANEL
REAR PANEL PORTS/TERMINALS/INDICATORS
- UC / LAPTOP
- 1. USB Input Type-B
- ROOM AV
- 2. USB 3.0 Type-A
- 3. USB 3.0 Type-C
- ADDITIONAL
- 4. RJ45 Network Gigabit Ethernet (LAN)
- 5. Pinhole Reset
- 6. Power port 24V/3.75A with lock connector
INSTALLATION
REMOVEABLE MOUNTING PLATE
The N 100 may be installed in almost any location that works for the room
design, requirements, etc. This includes installation on a wall behind a
typical conference room display or under a table. Be sure to allow for
adequate airflow on the ventilation grilles.
For installation on a wall, behind a conference room display, or under a table
use the provided mounting plate. Alternatively, place the device on a flat
surface, with or without the mounting plate, and the rubber feet will keep the
device in place.
- The mounting plate comes installed on the device and is easily removed.
- Unscrew the four screws attaching the bracket to the bottom of the device.
- Place the device on any flat surface that does not risk the power cord and connections being snagged, yanked, or crushed.
- The four rubber feet at the bottom will prevent the device from slipping on the surface.
MOUNT THE DEVICE
- The N 100 comes attached to the mounting plate via four mounting screws. If the bracket has been removed, attach it before attempting to mount the device.
- Locate a flat place to mount the device using the attached mounting plate.
- Use the four holes on the mounting plate to mark the locations for the wall anchors and screws.
- Use the provided screws and /or wall anchors to mount the device to the desired location.
CABLE MANAGEMENT
- Once the device is in place, use the built-in cable management retainer to keep cables organized and protected from accidental damage.
- Once the device is in the desired location, and the cables are connected and secure within the cable management retainer, attach the protective cover.
- The cover will snap into place. Secure the cover using the provided cover screw.
CONNECTIONS
COMPLETE SYSTEM DEPLOYMENT
_ Warning: _The Parlé N 100 power supply MUST NOT be connected to a VBC 2500 or ABC 2500 conference bar as the unit will be damaged. See the Parlé N 100 PSU warning label.
Note: To manage the parameters and settings of the N 100 device via web browsers, access the Web Administrator Console here.
CONTACT US
- Web: support.biamp.com
- Email: support@biamp.com
- Warranty: biamp.com/legal/warranty-information
- Safety & Compliance: biamp.com/compliance biamp.com/legal/warranty-information
- Biampinfo@biamp.com
- www.biamp.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>