DEWALT DXWT-PS202 Panel and Drywall Cart Instruction Manual

: June 6, 2024
: Dewalt

Table of Contents

DEWALT DXWT-PS202 Panel and Drywall Cart
PARTS DIAGRAM
PARTS INCLUDED
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
FUNCTIONS & FEATURES
WARNINGS AND SAFETY INFORMATION
Definitions: Safety alert symbols and words.
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DEWALT DXWT-PS202 Panel and Drywall Cart

PARTS DIAGRAM

Maximum Panel Load Space
Total Assembled Width
Total Assembled Depth
Total Assembled Height

PARTS INCLUDED

1 x Axle mount frame
1 x Platform frame
Ix Backrest frame
1x Backrest support tube
2x Handlebars
2x Steel core Flat-Free PU Wheels
4x Sman frame bolt (MB) [7]
4x Medium frame bolt(MB) 18]
2x Large frame bolt (MB) 19
2x25mm Axle washers
2x 25mm Star lock axle caps
2x Frame brackets
4xFlat washers
4x Nylon Lock Nuts

ASSEMBLY INSTRUCTIONS

Slide the first wheel onto the axle mount frame, making sure the offset side of the hub goes towards the body of the cart.
Slide the washer onto the axle. Then slide the star lock axle cap onto end and tap lightly with a hammer to lock into place.
Repeat steps 1-2 for the other wheel.
Attach the platform frame using 4 Small frame bolts. Make sure the pole inserts match the axle mount frame.
Connect the backrest support tube to the backrest frame using 1 Medium frame bolt.
Attach the 3 poles from Step 5. Secure to platform frame with 2 Large frame bolts and to the axle mount frame using 1 Medium frame bolt.
To finish assembly, insert and secure both handlebars to the backrest frame using 2 Medium frame bolts.

TOOLS REQUIRED

Not Included

Hammer

Wrench or 14mm Socket

FUNCTIONS & FEATURES

Anti-slip surface.
Load lips to prevent plates from sliding.
Double-sided push rod.
Flat-free DeWALT Steel core wheels.

WARNINGS AND SAFETY INFORMATION

WARNING: Read and understand Instruction Manual before operating the product. Failure to follow all instructions listed below may result in serious injury.

WARNING: Do not allow persons to operate or assemble this dolly until they have read this manual and have developed a thorough understanding of how the dolly works.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur.
WARNING: Do not exceed 1200 Lb (544 Kg) weight capacity of Dolly. Be aware of dynamic loading! The sudden load movement may briefly create excess load, causing product failure.

WARNING:

Always load evenly with the center of gravity of the load as near the center and rear of the plate as possible.
Obtain additional support for large or wide loads to prevent tipping.
DO NOT overload the dolly. Weight capacity: 1200 Lb (544 Kg)
DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the dolly is otherwise secured.
DO NOT use dolly on uneven ground and do not run over curbs or steps – use a ramp.
DO NOT allow others to ride on the dolly.
DO NOT use the dolly if any part is damaged, paying particular attention to the wheels.
Use a load restrainer, like a bungee cord to strap the load securely to the dolly if needed

Definitions: Safety alert symbols and words.

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: I ndicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.
(Used without words), indicates a safety-related message.

This product can expose you to chemicals including naphthalene, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to REDUCE THE RISK OF INJURY, USER MUST READ THIS INSTRUCTION MANUAL BEFORE OPERATING PRODUCT. Failure to follow all instructions may result in serious injury

SPECIFICATIONS

Wheel Dimensions 12″ (300 mm)
Size 65 X 24. 7 X 48.9″ 1651 x 628 x 1242 mm)
Base Plate 7×23″ (178×584)
Capacity 1200 Lb (544 Kg)

Made in Vietnam Hecho en Vietnam Fabrique en Vietnam Complies with UUCSA/ANSI standards. Cumple con las normas de UUCSA/ANSI Conforme aux tonnes UUCSA/ANSI Manufactured under license by: Fabricado bajo licencia por: Fabrique sous license par: SAM-Works HK Ltd. 11/F, Unit B, Winbase Centre 208 Queen’s Road Central Sheung Wan, Hong Kong Part No. DXWT-PS202 Copyright© 2020 DEWALT DEWALT® and GUARANTEED TOUGH.® are trademarks of Stanley Black & Decker, Inc. and used under license.