GE Appliances GBF655 Series GBF655SGPWW 24-Inch Built-In Dishwasher Owner’s Manual
- June 6, 2024
- GE Appliances
Table of Contents
OWNER’S MANUAL
GBF655 Series PBF665 Series Includes GE ProfileTM Series products
Write the model and serial numbers here: Model #
Serial #
You can find them on a label on the tub wall just inside the door.
GE is a trademark of the General Electric Company. Manufactured under
trademark license. 29-5953-2 05-18 M
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to
have you in the family.
We take pride in the craftsmanship, innovation, and design that goes into
every GE Appliances product, and we think you will too. Among other things,
registration of your appliance ensures that we can deliver important product
information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are
available in the Consumer Support section of this Owner’s Manual. You may also
mail in the pre-printed registration card included in the packing material.
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING THE
APPLIANCE
WARNING For your safety, the information in this manual must be followed
to minimize the risk of fire, explosion, electric shock, and to prevent
property damage, personal injury, or death.
WARNING PROPER INSTALLATION AND MAINTENANCE
This dishwasher must be properly installed and located in accordance with
the Installation Instructions before it is used. If you did not receive an
Installation Instructions sheet with your dishwasher, you can receive one by
visiting our Website at GEAppliances.ca.
- Connect the dishwasher/appliance to a grounded metal, permanent wiring system; or run an equipment-grounding conductor with the circuit conductors and connect to the equipment-grounding terminal or lead of the appliance.
- Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.
- Dispose of discarded appliances and shipping or packing material properly.
- Do not attempt to repair or replace any part of your dishwasher unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.
- Use only cord kit WG04F04614 or hard-wire to build electrical. Failure to follow this instruction could result in a risk of fire and personal injury.
- To minimize the possibility of electric shock, disconnect this appliance from the power supply before attempting any maintenance.
NOTE: Turning the dishwasher off does not disconnect the appliance from
the power supply. We recommend having a qualified technician service your
appliance.
WARNING WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS, INCLUDING
THE FOLLOWING :
- Use this appliance only for its intended purpose as described in this Owner’s Manual.
- Do not touch the heating element during or immediately after use.
- Use only detergents or wetting agents recommended for use in a dishwasher and keep them out of reach of children. Using a detergent that is not specifically designed for dishwashers will cause the dishwasher to fill with suds.
- Locate sharp items so that they are not likely to damage the door seal.
- Load sharp knives with the handles up to reduce the risk of cut-type injuries.
- Do not wash plastic items unless marked dishwasher safe or the equivalent. For plastic items not so marked, check the manufacturer’s recommendations.
- Do not operate your dishwasher unless all enclosure panels are properly in place.
- Do not tamper with controls.
- Do not abuse, sit on or stand on the door or dish rack of the dishwasher.
- To reduce the risk of injury, do not allow children to play with, on or inside this appliance at any time.
- Do not store or use combustible materials including gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
Small parts, such as rack clips and filter retaining posts, can be a choking hazard to small children if removed from the dishwasher. Keep out of reach of small children.
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING THE
APPLIANCE
WARNING WATER HEATER SAFETY
Under certain conditions, hydrogen gas may be produced in a water heater that
has not been used for two or more weeks.
HYDROGEN GAS IS EXPLOSIVE.
If the hot water has not been used for two or more weeks, prevent the
possibility of damage or injury by turning on all hot water faucets and
allowing them to run for several minutes. Do this before using any electrical
appliance connected to the hot water system. This simple procedure will allow
any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke,
use an open flame, or use the appliance during this process.
WARNING RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE DISHWASHER
Junked or abandoned dishwashers are dangerous…even if they will sit for “just
a few days.” If you are getting rid of your dishwasher, please follow the
instructions below to help prevent accidents.
- Do not allow children to play with, on, or inside this or any discarded appliance.
- Take off the door of the washing compartment or remove the latch by removing the screw from the latch receiver located on the top of the tub (as shown).
CAUTION TO PREVENT MINOR INJURY AND PROPERTY DAMAGE
- During or after the wash cycle, contents may be hot to the touch. Use care before handling.
- Close supervision is necessary if this appliance is used by or near children.
- Do not allow children to play around the dishwasher when closing the door, closing the upper rack, or while vertically adjusting the upper rack due to the possibility of small fingers being pinched.
- Non-Dishware Items: Do not wash items such as electronic air cleaner filters, furnace filters, and paintbrushes in your dishwasher. Damage to the dishwasher and discoloration or staining of the dishwasher may result.
- Load light-weight, plastic items so they do not become dislodged and drop to the bottom of the dishwasher–they might come into contact with the heating element and be damaged.
CAUTION ELECTRICAL REQUIREMENTS
- This appliance must be supplied with 120V, 60 Hz, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time-delay fuse.
- If the electric supply provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet.
- Your dishwasher circuit should not be used for any other appliance while the dishwasher is in operation as the dishwasher requires the full capacity of the circuit.
NOTICE
- If your dishwasher is connected to a wall switch, ensure that the switch is on prior to use.
- If you choose to turn the wall switch off between wash cycles, allow 5-10 seconds after turning the switch on before touching Start to allow the control to initialize.
- Use only powder, Finish® Quantum® Automatic Dishwashing Detergent, liquid detergents or rinse agents recommended for use in a dishwasher and
keep them out of the reach of children. Finish® Quantum® Automatic Dishwashing Detergent and Finish® Jet-Dry® Rinse Aid rinse agents have been approved for use in all GE Appliances dishwashers.
READ AND SAVE THESE INSTRUCTIONS USING THE DISHWASHER
Getting started
Features and appearance will vary throughout this manual.
-
Load Dishwasher
For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat trimmings, and excessive amounts of grease or oil. -
Add Detergent
Add the needed amount of detergent to the detergent dispenser. Use detergent such as Finish® Quantum® Automatic Dishwashing Detergent. See Dispensers section. -
Add Rinse Agent
Add rinse agents such as Finish® Jet-Dry® Rinse Aid to the rinse agent dispenser. See Dispensers section. -
Start Cancel
Press the Cycles button for the desired wash cycle. The light next to the button will be lit to indicate which wash cycle has been selected. Pressing the Cycles button will show various cycles in the display window. Press the button until the desired cycle is shown. NOTE: Actual cycle times vary based on soil level, water temperature, and options selected. The cycle may be selected with the door in the closed position. The cycle will not start until the Start Cancel button is pushed and the door is closed. You can cancel a cycle anytime during the cycle. Press the Start Cancel button three seconds during the drain to cancel it. Furthermore, you can carefully open the door (water may splash out) then the machine will stop running, close the door then press the Start Cancel button and the dishwasher will start to drain.
Auto
This cycle automatically senses the soil level and adjusts the wash cycle
accordingly. Time range: 1 hour 30 minutes – 2 hours 1 minute.
Heavy
This cycle is meant for heavily soiled dishes, cookware, pots, or pans with
dried-on or baked-on soils. Everyday dishes are safe to be used in this cycle.
Time: 2 hours 14 minutes.
Normal
This cycle is meant for daily, regular, or typical use to completely wash a
full load of normally soiled dishes and is designed to conserve both water and
energy. Time range: 1 hour 36 minutes – 1 hour 56 minutes. NOTE: Normal was
used to rate the energy efficiency of this dishwasher. Light
Light
This cycle is for light to medium soiled dishes. It is safe for china and
crystal with no options selected. Time: 1 hour 46 minutes.
Rinse
For rinsing partial loads that will be washed later. Do not use detergent.
Detergent is not dispensed during the rinse cycle. Time: 20 minutes.
Speed Cycle
This cycle will quickly wash lightly soiled dishes. Time: 30 minutes. A
shorter wash for lightly soiled loads that do not need drying.
Crystal
This cycle will efficiently wash dishes using about 2-5 gallons of water.
*Time: 2 hour 14 minutes.
Select Cycles
The light by the selected button will be lit to indicate which Option has been
selected.
Normal Temp
This option is for normally soiled dishes, optimizes wash performance while
conserving energy.
Wash Temp Boost
This option increases the temperature to help clean heavily soiled dishes and
will increase the cycle time as by 20 to 50 minutes. This option will also
improve dry performance on the Normal cycle.
Wash Temp or Sanitize Temp
This option raises the water temperature in the final rinse to sanitize
your dishware but may Temp Sani increases cycle time by 60 minutes. The cycle
length will vary depending on the temperature of or Sanitize your inlet water.
NOTE: This option is monitored for sanitization requirements. If the
cycle is interrupted during or after the main wash portion or if the incoming
water temperature is so low that adequate water heating cannot be achieved,
the sanitizing conditions may not be met. In these cases, the Sanitized or
Cycle Sanitized light may not illuminate at the end of the cycle. Utilizing
this option will modify the cycle to meet the requirements of Section 6, NSF
184 for soil removal and sanitization efficacy.
NOTE: NSF-certified residential dishwashers are not intended for licensed
food establishments.
Heated Dry
When the Heated Dry option is selected, the heater will work during the dry
process. This option is available for the Normal, Heavy, Light, Auto and
Crystal. Turns on the option for faster drying. This option may add up to 85
minutes to the cycle time. On models with Heated Dry, this option boosts the
temperature of the dishwasher during the final rinse portion of the cycle.
Steam PreWash
For use with heavily soiled and/or dried-on, baked-on soils. This option
MUST be selected PRIOR to starting the cycle. The Steam option adds up to 30
minutes to the cycle time. This option is available with Heavy, Auto, Light,
Normal, and Crystal cycles.
Wash Zones
Selecting either the Upper or Lower Wash Zones will target dishwashing of
just one rack. This will shorten the cycle time and conserve energy. This
option should be used when dishes are placed in only one rack.
Cyclone Jet
This option increases the power in the jets. Use this option when you want to
wash heavily soiled pots and pans, durable serving bowls, and other large
hard-to-clean dishes.
Delay Start
Delays the start of a wash cycle up to 24 hours depending on the model. Press
Delay Start, to select the number of hours. The hours will show in the display
window or the corresponding LED will light up. If you wish to cancel Delay
Start, hold Delay Start for three seconds and the delay time will be cleared.
If the delay has started, press Delay Start for three seconds, the program and
function remain unchanged, the machine enters standby and if press Start
Cancel for three seconds, the program and function remain unchanged, the
machine enters a washing operation state.
Control Lock
You can lock the controls to prevent selections from being made. You can also
lock the controls after you have started a cycle to prevent cycle changes. For
example, children cannot accidentally start the dishwasher by pressing buttons
with this option selected.
To LOCK the dishwasher control, press the Heated Dry and Wash Temp buttons for
3 seconds and the lock indicator will appear on the display.
To UNLOCK the dishwasher control, press the Heated Dry and Wash Temp buttons
for 3 seconds and the lock indicator will no longer appear on the display.
Start Dishwasher
Start
Close the door and press the Start button to start the cycle or begin the
Delay Hours countdown. The display will turn off if the machine keeps the
standby state 15 minutes. To activate the display, press any button.
Interrupt or pause
To interrupt or pause a dish cycle, slowly open the door. To restart or resume
the cycle, close or Pause the door then press Start Cancel
Cancel
To cancel a wash cycle, press and hold the Start Cancel button for 3 seconds.
The dishwasher will drain and display start to 60 seconds countdown. After
draining,emit a beep
sound and the machine enter the standby state.
Restart Dishwasher
When the display shows the error codes, press the Delay Start and Cycles
buttons at the same time, the machine will be reset to power-on state.
Cycle Indicator Lights and Sounds
Sanitized Indicator If the sanitized cycle was selected, the sanitized
indicator will be turned on at the end of the cycle, if the NSF requirements
for sanitization are not reached. The light will not turn on. Certified
residential dishwashers are not intended for licensed food establishments. The
sanitize cycle is NSF certified.
Dispensers
Check the Water Temperature
The entering water should be at least 120°F (49°C) and not more than 150°F
(66°C) for effective cleaning and to prevent dish damage. Check the water
temperature with a candy or meat thermometer. Turn on the hot water faucet
nearest the dishwasher, place the thermometer in a glass, and let the water
run continuously into the glass until the temperature stops rising.
Use a Rinse Agent
Rinse agents, such as Finish® Jet-Dry® Rinse Aid are designed for great drying
action and to protect against spots and film build-up on your dishes, glasses,
flatware, cookware, and plastic.
Filling the Rinse Agent Dispenser
The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under
normal conditions, this will last approximately one month.
- Make sure the dishwasher door is fully open.
- Open the rinse agent dispenser door.
- Slowly add rinse agent until the cup is full. You may need to pause several times to allow rinse aid to settle. NOTE: Indicator window does not light up.
- Clean up any spilled rinse agent with a damp cloth to prevent foam from forming inside the dishwasher.
- Close the rinse agent dispenser door.
Rinse Aid Setting
The amount of rinse agent released into the final wash can be adjusted. If
water drops or hard water spots remain on dishes after the dry cycle, increase
the setting.
To adjust the setting
Open the Rinse Agent dispenser door; then turn the adjuster clockwise to
increase the amount of rinse agent, counterclockwise to reduce the amount of
rinse agent.
Detergent Dispenser
The detergent dispenser is located in the center of the dishwasher door. It
has two compartments. The main wash compartment is found inside the detergent
dispenser. To open, press the button on the side of the dispenser. The pre-
wash compartment is on the lid of the detergent dispenser. Use the pre-wash
compartment only when your water is extremely hard or when you have a heavily
soiled load. The pre-wash compartment is not used when tablet or packet
detergents are used.
NOTE: Do not load large items in the lower rack where they may block the
wash jets from rinsing out the detergent dispenser.
You may use tablet, packet, powder, liquid or gel automatic dishwasher
detergent. Make sure you use only detergents specifically labeled for use in
automatic dishwashers. Never use liquid hand dish detergent in an automatic
dishwasher. Studying and poor wash performance will result from the use of
improper detergents.
Detergents should be stored in a dry location and in their original container
to prevent loss of effectiveness. Place detergent in the cup just prior to
starting the dishwasher and then close the cover. The cover will open during
the wash cycle.
Filling the Detergent Dispenser
GE Appliances recommends using detergent in tablet or packet form. Independent
testing has shown this form of detergent is very effective in the dishwasher.
Finish® Quantum® Powerball® is an example of this type of detergent.
Simply put a tablet or packet into the main wash compartment and close the
detergent cup cover. Please notice that the tablet or packet must be placed in
the main wash compartment of the detergent cup. If the tablet or packet is
placed in the prewash compartment or tossed in the bottom of the dishwasher,
the detergent will be flushed down the drain in a very short period of time
and will thus be wasted. Wash performance will be very poor as a result.
If you choose to use detergent in powder, liquid or gel form, the amount of
detergent you use will be determined by the hardness of your water, the
temperature of your water, and the food soil load inside the dishwasher.
Contact your water company to get information about the hardness of the water
in your area. Water hardness is measured in grains per gallon. Use this
information and the table above to determine the amount of detergent to use.
You may purchase a hard water test strip from GE Appliances. Call 800.661.1616
and ask for part number WG04F04842.
Use the table as a starting point and then adjust the amount of detergent you use. Use just enough to get good wash performance. Using just the right amount of detergent will provide great wash performance without wasting detergent or etching glassware.
Number of Grains/Gal. | Detergent Cup(s) to Fill |
---|---|
Less than 4 | Fill cup to 1/3 full |
4 to 8 | Fill cup to 2/3 full |
8 to 12 | Fill cup completely full |
Greater than 12 | Fill both the main wash cup and prewash cup |
Using too much detergent with very soft and/or very hot water may cause a
condition called etching on your glassware. Etching is permanent cloudiness in
your glassware. This condition is irreversible. However, using too little
detergent will cause poor wash performance.
DO NOT USE HAND DISH DETERGENT
NOTE: Using a detergent that is not specifically designed for dishwashers
will cause the dishwasher to fill with suds. During operation, these suds will
spill out of the dishwasher vents, covering the kitchen floor and making the
floor wet.
Because so many detergent containers look-alike, store the dishwasher
detergent in a separate space from all other cleaners. Show anyone who may use
the dishwasher the correct detergent and where it is stored.
While there will be no lasting damage to the dishwasher, your dishes will not
get clean using a dishwashing detergent that is not formulated for automatic
dishwashers.
For best dishwashing results, follow these loading guidelines. Features and
appearance of racks and silverware baskets may vary from your model.
Upper Rack
The upper rack is primarily for glasses, cups, and saucers. For best wash
performance, tilt cup and glass openings toward the center of the rack. Other
items such as pots, pans, and plates may be placed in the upper rack. This is
also a secure place for dishwasher-safe plastic items. The upper rack can be
used for odd-sized utensils. Saucepans, mixing bowls, and other similarly
shaped items should be placed face down for best wash performance. Ensure
small plastic items are secure so that they cannot fall on the heater at the
bottom of the dishwasher, potentially damaging the item. Some models are
equipped with a hidden heater, so dishwasher-safe plastic items can be placed
in the lower rack.
IMPORTANT: Ensure items in the upper rack do not interfere with the 3rd
Rack (on some models) when loading and unloading.
IMPORTANT: Ensure that items do not protrude through the bottom of the
rack or silverware basket where they will block the rotation of the middle
spray arm. This could result in noise during operation and/or poor wash
performance.
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model.
Lower Rack
The lower rack is best used for plates, saucers, and cookware items. Large
items, such as broiler pans and baking racks should be placed along the sides
of the rack. If necessary, oversized glasses and mugs can be placed in the
lower rack to maximize loading flexibility. Plates, saucers, and similar items
should be placed between the tines in the direction that allows the item to
remain secure in the rack.
NOTE: Do not load large items in the lower rack where they may block the
wash jets from rinsing out the detergent dispenser.
The lower rack fold-down tines (on some models) can be adjusted to different
upright flexibility for hard-to-fit or extra-large items.
WARNING The clips can be a choking hazard for small children if removed
from the dishwasher. Keep out of reach of children.
To change the direction of the fold-down tines, lower the tines, then pull
away from the bar clips that secure the tines to the rack and remove them.
Reverse the direction of the tines, orienting the handle on the opposite side
of the rack. Reattach the tines to the bar clips by pushing the tines back
until they click in place. The indexer will also need to be switched to the
opposite side of the dishwasher. To remove the indexer, simply slide it in the
direction labeled “unlock.” Then, align the indexer with the rack on the other
side and slide in the direction that says “lock” in order to reattach the
indexer to the rack.
IMPORTANT: It is important to ensure that items do not protrude through
the bottom of the rack or the silverware basket where they will block the
rotation of the lower spray arm. Also, ensure that large plates, pots, or tall
items don’t hit the mid spray arm. This could result in noise during operation
and/or poor wash performance.
Silverware Basket
Place flatware in the removable silverware baskets. Sharp objects, such as
forks and knives, may be placed with the handles facing up, in order to
protect your hands. For the best wash performance, place other items such as
spoons with the handles facing down. Avoid allowing items to nest together,
which may keep them from being properly washed. When loading, distribute items
evenly in the basket.
- Spoons
- Knives
- Salad Forks
- Forks
- Large Forks
- Large Spoons
The silverware baskets may also be used for small items, such as measuring
spoons, baby bottle nipples, plastic lids, or corn cob holders. The silverware
basket covers can be closed to contain small items.
IMPORTANT: Do not load large or tall utensils where they may block the
detergent dispenser, mid spray arm, or become trapped between the door and the
gasket when the door is closed.
WARNING DO NOT LEY ANY ITEM EXTEND THROUGH THE BOTTOM
For best dishwashing results, follow these loading guidelines. Features and
appearance of racks and silverware baskets may vary from your model.
3rd Rack (on some models)
The 3rd rack is the recommended location for silverware and large utensils.
CAUTION
Take care when loading, unloading, or transporting the silverware or
utensil tray. The tray may contain sharp or heavy items. If items are dropped
from the tray or the tray is dropped, the injury could occur.
IMPORTANT NOTES:
- Do not allow cutlery of different materials to touch each other in the 3rd rack. Doing so may cause discoloration of the cutlery.
- The tray is only meant to be used with a GE Appliances 3rd rack dishwasher to hold silverware, cooking utensils, and other small items. Using the tray for any other purpose could result in damage to the tray or damage to anything interacting with the tray.
- Ensure that the 3rd rack is fully closed before shutting the dishwasher door. Shutting the door with the rack partially extended could cause damage to the dishwasher.
Adjusting the 3rd Rack (on some models)
The 3rd rack is the recommended location for silverware and large utensils.
Care and cleaning
Control Panel
To clean the control panel, use a lightly dampened cloth. Then dry thoroughly.
Exterior Door Panel
Before cleaning the front panel, make sure you know what type of panel you
have. Refer to the last two letters of your model number. You can locate your
model number on the left-hand tub wall just inside the door. If your model
number ends with BB, CC, WW, SA, ES, DS or TS then you have a painted door
panel. If your model number ends with SS, then you have a Stainless Steel door
panel. If your model number ends with II, then you have an Integrated door
panel.
Follow the instructions below for cleaning the door panel for your specific
model.
Painted Door Panel (model numbers ending in BB-black, CC-bisque, WW-white, SA-
silver, ES-slate, DS-black slate or TS-black stainless steel).
Use a clean, soft, lightly dampened cloth, then dry thoroughly.
Stainless Steel Door Panel (model numbers ending in SS)
For cleaning rust and tarnish, cleaners with oxalic acid such as Bar
Keepers Friend Soft CleanserTM will remove rust, tarnish, and small blemishes.
Use only a liquid cleanser free of grit and rub in the direction of the brush
lines with a damp soft sponge. Do not use appliance wax or polish on the
stainless steel.
For other blemishes and marks, use Stainless Steel Magic or a similar
product using a clean soft cloth. Do not use appliance wax, polish, bleach or
products containing chlorine on Stainless Steel. Visit your local home store
for more details or call 800.661.1616.
Integrated Door Panel (model numbers ending in II)
This is a custom-installed door panel, and you will need to refer to the
cabinet manufacturer’s recommendations for proper cleaning.
Dishwasher Interior
To clean and deodorize your dishwasher, use citric acid or Finish® Dishwasher
Cleaner, a detergent additive. Finish® Dishwasher Cleaner will break up
mineral deposits, and remove hard water film and stains. You can order citric
acid GE Appliances kit # WG04A00103 through GE Appliances Parts by calling
800.661.1616 or you can visit your local home store.
Stainless Steel Inner Door and Tub
The stainless steel used to make the dishwasher tub and inner door provide the
highest reliability available in a GE Appliances dishwasher.
If the dishwasher tub or inner door should be scratched or dented during
normal use, they will not rust or corrode. These surface blemishes will not
affect their function or durability.
Cleaning the Filters
For best performance and results, the filter assembly must be cleaned once a
month. The filter efficiently removes food particles from the wash water,
allowing water to be recirculated during the cycle. For this reason, it is a
good idea to remove the large food particles trapped in the filter frequently
by rinsing the main filter and cup under running water.
To remove the filter assembly, follow the 3 steps shown below. To clean the
main filter and fine filter, use a cleaning brush. The dishwasher must never
be used without the filters. Improper replacement of the filter may reduce the
performance level of the appliance and may damage dishes and utensils.
Protect Against Freezing
If your dishwasher is left in an unheated place during the winter, ask a
service technician to:
- Turn off electrical power to the dishwasher. Remove fuses or trip circuit breakers.
- Turn off the water supply and disconnect the water inlet line from the water valve.
- Drain water from the water inlet line and water valve. (Use a pan to catch the water.)
- Reconnect the water inlet line to the water valve.
Does Your Dishwasher Have an Air Gap?
An air gap protects your dishwasher against water backing up into it if a
drain clogs. The air gap is not a part of the dishwasher. It is not covered by
your warranty. Not all plumbing codes require air gaps, so you may not have
one.
Check the air gap any time your dishwasher isn’t draining well.
The air gap is easy to clean.
- Turn off the dishwasher and lift off the air gap cover.
- Remove the plastic cap under the cover and clean with a toothpick.
- Replace the cap and cover when the air gap is clean.
TROUBLESHOOTING TIPS
Troubleshooting tips … Before you call for service
Problem | Possible Cause | What To Do |
---|---|---|
Start status indicator light flashing | The door was opened or the cycle was | |
interrupted. | Press the Stan button once and close the door whin |
4 seconds to start the dishwasher Press the Start button a second time when
the dishwasher is running only if you wish to cancel the cycle.
Dishwasher BEEPS once every minute| This Is a reminder that your dishwasher
door has been left open during operation. It will continue beeping until you
press Start and close the door.| Press Start and close the door.
Beeping at the end of the cycle (on some models)| This Is Normal. The
dishwasher will beep at the end of the cycle.|
Dishes and flatware not clean| Ultra-Fine Filter or Fine Filter Is clogged.|
See the Care and Cleaning section.
Low inlet water temperature.| Make sure inlet water temperature is correct
(see the USING THE DISHWASHER section). Tum on the hot water faucet nearest
the dishwasher. let run until the water temperature slops rising. Then start
the dishwasher and turn off the faucet. This ensures the entering water is
hot. Select Wash Temp Boost or Boost Temp if available.
Water pressure is temporarily low.| Turn on a faucet. Is water coming out more
slowly than usual? If so. wait until pressure 6 normal before using your
dishwasher. Normal water pressure to the dishwasher should be 20-120 psi.
Air gap or disposer clogged.| Clean the air gap or flush the disposer.
High drain loop or air gap not Installed.| Refer to the InstaLstion
Instructions for proper drain line installation.
Improper rack loading.| Make sure large dishwater does not block the detergent
dispenser or the wash arms. See the Loading section.
Poor performing detergent.| Use a highly rated detergent such as Finish.
Quantum Automatic Dishwashing Detergent.
Spots and filming on
glasses and flatware| Extremely hard water.| Use rinse agents such as Finish.
Jet-DryRinse Aid to prevent spots and prevent new film build-up. If water is extremely nerd. a softener may be required. Low inlet water temperature.| Make sure water temperature is at least 120i (49
CI
Overloading or improper loading of the dishwasher.| Load dishwasher as shown
in the Loading section
Old or damp powder detergent.| Make sure detergent is fresh. Use a highly
rated detergent such as Finish. Quantum’ Automatic Dishwashing Detergent.
Rinse agent dispenser empty.| Refill with rinse agent such as Finish. Jet-Dry.
Rinse Aid.
Too little or low-performing detergent.| Make sure you use the proper amount
of highly rated detergent.
Cloudiness on glassware| Combination of soft water and too much detergent.|
This is called etching and is permanent. To prevent Wes from happening. use
less detergent if you have soft water. Wash glassware in the shortest cycle
that MI get it clean
Low performing phosphate-free detergent.| See A white film on glassware.
dishware and the Interior in this TROUBLESHOOTING section.
Water temperature entering the dishwasher exceeds
150°F (66°C)| This could be etching. Lower the water heater temperature.
Suds in the tub| Wrong detergent.| Use only automatic dishwasher detergents to
avoid sudsing. Finish Quantum Automatic Dishwashing Detergent has been
approved for use in all GE Appliances dishwashers.
To remove suds from the tub. open the dishwasher and let suds dissipate. Open
the door. press and hold Start for 3 seconds. and dose the door.
---|---|---
The rinse agent was spilled.| Always wipe up rinse agent spas immediately.
Detergent left In dispenser cups| Dishes or utensils are blocking the
detergent cup.| Reposition the dishes. so the water from the lower spray arm
can flush me a detergent cup. See the Loading section. Reposition the tall
utensils a heavy silverware that may be keeping the dispenser cup door from
opening. See the Loading section. Don’t place large bowls pots directly under
the detergent dispenser.
Black or gray marks on dishes| Aluminum utensils have rubbed against dishes.|
Remove marks with a mild. abrasive cleaner.
Dishes don’t dry| Low Inlet water temperature.| Make style inlet water
temperature is at least 120•F (49t). Select Heated Dry.
Use Wash Temp Boost or Boost Temp option.
Select a higher cycle. such as Wash Temp Sant Sanitize Temp or Heavy.
The rinse agent dispenser Is empty.| Check the rinse agent dispenser and fill
as required.
Additional drying time Is needed.| Leave door dosed after the Clean Iola
appears to allow the fan to run an additional 00 minutes.
Note: II you open the door. gas fan extension will be canceled.
The Control panel respOnded to inputs but the dishwasher never filled with
water| The door may not be completely closed.| Make site the door is firmly
dosed.
Water valve may be turned al.| Make site water valve (usually located in order
the sink) Is turned on.
Flood float may be stuck.| Remove Ultra-Fine fair and allay tap the pece under
the ultra foe filter that looks Ike a salt Maker. Replace the filter
Stained tub interior| White film on Inside surface— hard water minerals.| GE
Appliances recommends Finish Jet-Der Rinse Aid to help prevent hard water
mineral deposits from forming. Run the dishwasher with amid acid to remove
mineral deposits. Caw add (Pan number: WD35X151) can be ordered through GE
Appliances Parts. See Creek cover for wondering mansion. Alternatively.
purchase Finish. Dishwasher Cleaner and blow the directions on the label.
The dishwasher won’t run| The fuse is blown or the circuit breaker is
tripped.| Replace fuse or reset circuit breaker. Remove any other appliances
from the circuit.
The power is turned off.| In some installations. the power to the dishwasher
is provided through a wall switch. often located next to the disposer switch.
Make site are on.
The Control panel is locked.| Unlock the control panel. See the Getting
started section.
The possible leak is detected.| Call for service at SO0.561.3344
A proper Start sequence was not followed.| See the USING THE DISHWASHER
section.
Control panel lights go off when you’re setting controls| Time too long
between touching Of selected buttons.|
Water standing In the bottom of the tub| Air gap is clogged.| Clean the air
gap. See the CARE AND CLEANING section.
---|---|---
High drain loop or air gap not installed.| Refer 10 the Instalauon Instmcbons
for proper dram line installation.
Water won’t pump out of the tub| The drain is clogged.| If you have an air
gap. dean it. See the CARE AND CLEANING section.
If the dishwasher drains into a disposer. run disposer clear. Check to seed
your kitchen sink is draining wet. If not you may need a plumber.
Steam| This Is Normal.| Warm. moist air comes through the vent dunng drying
and when water is being pumped our This is necessary for drying.
Sanitized or Cycle Sanitized light does not illuminate at the end of the
cycle| The door was opened and the cycle was Interrupted during the final
rinse.| Do not interrupt the cycle by opening the door dunng the wash cycle.
The incoming water temperature was too low,| Raise the water heater
temperature to between 120°F and 1501F (49t and 66`C).
Noise| Normal operating sounds: Beeping at the end of the cycle (on some
models): Detergent cup opening; Water entering dishwasher: Motor stops and
starts at various times during cycle: Spray arms start and stop at various
times: Drain pump sounds during pump-out: The drain pump starts and stops
several times during each drain.| These we all normal. No action is required.
Rattling dishes when the spray arm rotates.| Make sure dishes are properly
loaded. See the Loading section.
Rattling silverware against the door during the wash.| Tall utensils may be
placed in the upper rack to avoid bumping against the inner doze dunng wash
cycle.
A white film on glassware. dishware and the Interior| This problem is likely
caused by a low-quality phosphate-free dishwasher detergent.| To remove the
wive film, run your dishes through a dishwasher cycle with tine acid. Use a
WG04A00103 citric lead kit found online. Otherwise. use Finish’ Dishwasher
Cleaner found at your local grocery store. Pour the citric acid in the
detergent cup and dose the cover. Place the fired but otherwise clean
glassware and dishware in the dishwasher Leave silverware
and other metal items out of the Dishwasher. Turn the dishwasher on and let it
ion through a complete cycle without detergent The glassware.share. and
dishwasher should come out film free. Altemabvely. a vinegar rinse may be
used. Pour 1 cup (240 ml) of vinegar into the dishwasher Jost after the
detergent cup opens and let the dishwasher complete its cycle.This may be
repeated several times a year as needed. The use of a nose agent such as
Finish° Jet-Dry Rinse Aid may help minimize a repeat WO up of film. Also. the
use of a highly rated detergent such as Finish* CluaMurm Automatic Dishwashing
Detergent will help prevent film bued-up.
WARRANTY
Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.
GE Appliances Dishwasher Warranty
GEAppliances.ca
All warranty service is provided by our Factory Service Centers or an
authorized Customer Care® technician. To schedule service online, visit us at
https://service.geappliances.ca/servicio/en_CA/, or call GE Appliances at
800.561.3344. Please have your serial number and your model number available
when calling for service.
Servicing your appliance may require the use of the onboard data port for
diagnostics. This gives a GE Appliances factory service technician the ability
to quickly diagnose any issues with your appliance and helps GE Appliances
improve its products by providing GE Appliances with information on your
appliance. If you do not want your appliance data to be sent to GE Appliances,
please advise your technician not to submit the data to GE Appliances at the
time of service.
For the period of
One year From the date of the original purchase
GE Appliances will replace
Any part of the dishwasher which fails due to a defect in materials or
workmanship. During this limited one-year warranty, GE Appliances will
provide, free of charge, all labor and in-home service to replace the
defective part.
What GE Appliances will not cover (for customers in Canada):
- Service trips to your home to teach you how to use the product.
- Improper installation, delivery, or maintenance.
- Failure of the product if it is abused, misused or used for other than the intended purpose or used commercially.
- Replacement of house fuses or resetting of circuit breakers.
- Product not accessible to provide required service.
- Damage to the product caused by accident, fire, floods, or acts of God.
- Incidental or consequential damage caused by possible defects with this appliance.
- Cleaning or servicing of the air gap device in the drain line.
- Damage caused after delivery including damage from items dropped on the door.
This warranty is extended to the original purchaser and any succeeding owner
for products purchased for home use within Canada. If the product is located
in an area where service by a GE Appliances Authorized Servicer is not
available, you may be responsible for a trip charge or you may be required to
bring the product to an Authorized GE Appliances Service location for service.
EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of
merchantability or fitness for a particular purpose, are limited to one year
or the shortest period allowed by law.
WARRANTOR IS NOT RESPONSIBLE FOR CONSE QUEN TIAL DAMAGES.
Extended Warranties: Purchase a GE Appliances extended warranty and learn
about special discounts that are available while your warranty is still in
effect. Contact your retailer of purchase for more details.
CONSUMER SUPPORT
Consumer Support
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances
Website 24 hours a day, any day of the year! You can also shop for more great
GE Appliances products and take advantage of all our online support services
designed for your convenience. In Canada: GEAppliances.ca.
Register Your Appliance
Register your new appliance online at your convenience! Timely product
registration will allow for enhanced communication and prompt service under
the terms of your warranty, should the need arise. You may also mail in the
pre-printed registration card included in the packing material. In Canada:
https://service.geappliances.ca/servicio/en_CA/
Schedule Service
Expert GE Appliances repair service is only one step away from your door. Get
online and schedule your service at your convenience any day of the year. In
Canada: https://service.geappliances.ca/servicio/en_CA/ or call 800.561.3344
during normal business hours.
Extended Warranties
Contact your retailer of choice regarding extended warranties to purchase a GE
Appliances extended warranty and learn about special discounts that are
available while your warranty is still in effect.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or
accessories sent directly to their homes via their local parts distributor.
Or, call 800.661.1616 during normal business hours.
Instructions contained in this manual cover procedures to be performed by
any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE Appliances,
contact us on our Website with all the details including your phone number, or
write to Director, Customer Relations
MC Commercial Inc.
Suite 310 – 1 Factory Lane,
Moncton NB, E1C 9M3
References
- Magasin GE Canada | Homepage
- GE Appliances Canada | Homepage
- Magasin GE Canada | Homepage
- Canada Service Site | Homepage
- Canada Service Site | Homepage
- Canada Service Store
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>