HOPESIA Filtered Shower Head with Pause and Jet User Manual

HOPESIA Filtered Shower Head with Pause and Jet

How To Use

10 Spray Modes Switch Change gears left and right through the small lever

Tips:

1. Before use, please familiarize yourself with the 10 modes of the shower head.
2. Modes 9-10 are strong spray modes on the bock, please do not use them on people.

Replace Filter

Filter Handle Removal And Replacement Steps

The filter element does not distinguish the lnstallation direction.
Filter life depends on frequency of use. Generally, the service life of the filter element is about one year. If it is used frequently, it is recommended to replace it every 4-6 months.

1. Unscrew to the left

2. Removing the shower rod

3. Renewing filter cartridges

4. Tighten to the right

Installation Guide

Step 1: Tope the threads of the shower arm Unscrew your old shower head from the shower arm, then simply put 3-5 turns of Teflon Tope wrap around the shower arm threads. (Note: Teflon Tape wrapped around the red plastic wheel, squeeze the red wheel out of the white plastic ring by hands.)

Step 2 : Screw the bracket to the shower arm Attach the bracket rotating Clockwise onto the shower arm and hand tighten as tight as possible.(Note: The white plastic o-ring on the bracket is open rather than completely dosed. If you tighten with the wrench, place a piece of cloth over the pipe and turn rust a slight turn. Over tightening may cause damage. This type of damage is not covered under warranty.)

Step 3: Connect the hose to the bracket and shower head Put a washer into the hose CONICAL NUT and connect It to the shower head. The water saver Is Installed at the end of the shower and connected with the bell mouth pipe. Put another washer Into the hose HEX NUT and connect it to the brocket.(Note: Please don’t reverse the joint between the two ends of the hose. Normally there might be some threads of the bracket exposed.)

Step 4 : Installation Check out Ensure that all coupling nuts ore tightened, hold the whole bracket by hand and rotate the boll joint to adjust the angle you need. Then turn on the main water supply and check for leakage. (Note: If find any water leaks, please check that you followed steps 1-3 and that installation was completed per the instructions.)

We are equipped with water saver yellow 1.8GPM and white 2.SGPM for you to choose to install.

Tips : We send on extra Wosher, and the rest hove been Installed in the accessories.
The hex nut is connected to the bracket, and the bell mouth Is connected to the shower head.
Note: If you find o leak In the connection during use, please follow these steps:

1. Make sure there is o block washer at each connection, otherwise It may cause leakage.
2. Wrap 3-4 layers of teflan tape around the leaking connection threads and reinstall. The filter element replacement cycle is about 4·6 months.

Please feel free to contact us if there are any missing accessories or if there is any abnormality after receiving the goods, we will get in touch with you within 24 hours.

Common Problem

Q: Why does the shower head keeps foiling down and it doesn’t securely hold on the bracket?
A: Maybe you have the connections on the wrong ends. Switch the conical end to the shower head and it will fit in the holder.
Q: How can I remove the flow restrictor?
A: The flow restrictor is located at the base of the shower head. Before you screw the hose to the shower head, get a needle nose pliers and pull the flow restrictor out with it.
Q: Why doesn’t the pause mode shut off the water completely?
A: Considering the Internal pressure balance, the pause mode will not completely shut off the water. It keeps water temperature what you wont. Easy to use and save water, which brings you more convenience.
Q: Why does it leak?
A: If you experience leakage an improper installation could have occurred. The solution is
as below. If the hose is leaking, place the black washer into both ends of the hose to prevent leakage.
b. If the shower arm is leaking, it could possibly due to the short threads on the shower arm. I Place the spore washer on the mesh washer of the bracket nut to prevent water leakage.
c. If the bracket is leaking, it could possible be due to the white plastic open 0-ring of the bracket became loose during the long-term transit. You will need to reinstall the bracket by following the steps below.
Note: If water leaks from the place where the shower filter is installed, you can unscrew the 0-rlng and reinstall it.

1. First screw the cylindrical ring out of the other parts of the bracket;

2. Take out the brass swivel ball joint;

3. Use your hands to press the white O-ring down flat, keep it clode to the mouth of the cylindrical ring;
   

4. Place the brass swivel hall joint into the cylindrical ring; then tighten the other part of the bracket to the cylindrical ring.

Customer Service

If you have any questions or suggestions, you can contact us at any time (In the event of
o serious spill, do not hesitate please contact us immediately.)
E-mail: support@hopesla.net
Handheld Showerheads makes your life easier, enjoy the joy of life to the fullest.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>