BRESSER CM3BLU RC Alarm Clock Instruction Manual

: June 6, 2024
: BRESSER

Instruction manual
Radio despertador

MyTime W
Art. No. 8020401 CM3BLU · 8020401 CM3WHI
8020401 GYEBLU · 8020401 GYEWHI

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

www.bresser.de/P8020401000000

WARRANTY

**www.bresser.de/warranty_terms
**

IMPORTANT NOTE!
Do NOT touch the touch-sensitive upper side of the housing during the automatic time signal reception or when making any manual settings Touching the upper side of the housing will activate the snooze function and all other functions will be blocked.

GENERAL INFORMATION

About this Instruction Manual
These operating instructions are to be considered a component of the device.

Please read the safety instructions and the operating instructions carefully before use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, he instruction manual must be provided to the new owner/user of the product.

Intended Use
This product is intended only for private use. It was developed as an electronic medium for the use of multimedia services.

DANGER!
You will find this symbol before every section of text that deals with the risk of minor to severe injuries resulting from improper use.

CAREFUL!
You will find this symbol in front of every section of text which deals with the risk of damage to property or the environment.

GENERAL WARNINGS

RISK OF CHOKING!
This product contains small parts that could be swallowed by children. There is a RISK OF CHOKING.

RISK of ELECTRIC SHOCK!
This device contains electronic components that operate via a power source (power supply and/ or batteries). Children should only use the device under adult supervision. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.

RISK OF CHEMICAL BURN!
Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes, and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.

****RISK of FIRE/EXPLOSION!
Do not expose the device to high temperatures.
Use only the supplied power supply or the recommended batteries. Do not short- circuit the device or batteries or throw them into a fire! Excessive heat or improper handling could trigger a short circuit, a fire, or an explosion.

****RISK of property damage!
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Do not immerse the unit in water.
Do not subject the unit to excessive force, shock, dust, extreme temperature, or high humidity, which may result in malfunction, shorter electronic life span, damaged batteries, and distorted parts.

**** This device cannot be operated simultaneously with batteries and a power adapter. This could lead to irreparable damage to the device; the manufacturer is not liable for this damage!

**** Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if it has not been used for a long time.

**** The manufacturer is not liable for voltage damage due to improperly inserted batteries or through the use of an improper power adapter!

NOTES ON CLEANING

Before cleaning the device, disconnect it from the power supply (remove plug or remove batteries)! Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.

Protect the device from dust and moisture. Store it in the supplied bag or transportation packaging. The batteries should be removed from the unit if it
has not been used for a long time.

EC DECLARATION OF CONFORMITY

Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. This can be viewed any time upon request.
A detailed declaration of conformity is available under www.bresser.de/download/8020401000000/ CE/8020401000000_CE.pdf

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste disposal service or environmental authority for information on the proper disposal.

Do not dispose of electronic devices in the household garbage!
As per Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.

SCOPE OF DELIVERY (Fig. 1)

Main unit (A), power plug (B), Instruction manual Required batteries (optionally, not included with purchase): 3 pcs. Micro bateries (1.5V, AAA type)

PARTS OVERVIEW (Fig. 2-3)

LCD
SNOOZE/LIGHT button
MODE button
SET button
UP-button
DOWN-button
RESET-button
DC jack
Battery compartment
Touch sensitive upper side of the housing

POWER SUPPLY

Main operation

Put the DC power plug (Fig. 1, B) in the DC jack (Fig. 2, 8). Put the mains plug into the wall outlet.
Push the RESET knob to initialize the automatic km/h time signal.

Battery operation

Open the battery compartment door.
Install 3 batteries (AAA size 1.5V) strictly according to the polarities shown.
Reinsert the battery compartment door.

RECEPTION OF RADIO CONTROLLED TIME SIGNAL

The time and date are radio-controlled. The current time and date are automatically synchronized with the time signal transmitted from Europe.
When used for the first time the clock will start to receive the RC signal in 5 minutes with the signal LED flashing.

NOTE!

Every day the unit will automatically search for the time signal at 1:00am , 2:00 am and 3:00 am.
Always place the unit away from interfering sources such as TV set, computer, etc.
Avoid placing the unit on or next to metal plate.
The use in airports, cellars, high-rise buildings, or factories is not recommended due to reception problems.
Do not start reception on a moving article such as vehicle or train.

MANUAL TIME SETTING

In normal time mode, press and hold SET key for 3 seconds to enter the year setting.
Press or key to set the desired value.
Press SET key again, Month digit flashes, press or key to change its value.
Repeat the above operation to set the time in this order: Year > Month > Date > 12/24 hr mode > Time zone (+/- 12 hours) > Hours > Minutes.
Press [ SET ] key to save and exit the setting or let it exit automatically 30 seconds later without pressing any key.

ALARM TIME SETTING

In normal time mode, press SET key to switch to alarm mode.
In alarm mode, press and hold SET key for approx. 3 seconds until alarm hour digit flashes.
Press or key to change the value.
Repeat the above operations to set time in this order: Hour > Minute
Press SET key to save and exit the setting, or let it exit automatically 10 seconds later without pressing any key.

SNOOZE FUNCTION

If no key is pressed during the alarm period, the alarm will turn off automatically. Alarm beeping lasts for 2 minutes.
Press SNOOZE button to stop the current alarm and enter snooze. Alarm icon AL will be flashing continuously. The alarm will sound again in 5 minutes. Alternatively, touch the upper side of the housing gently to activate the snooze function.

ALARM FUNCTION TURN OFF OR ON

In normal time mode, press [ SET ] key to switch to alarm mode
In alarm mode, press [ UP ] key to turn off or on alarm function.

DISPLAY BRIGHTNESS

For the LED display different levels of brightness can be set as follows: bright, middle, glimmer. (Only when operated with DC power adapter)

Press and hold [ SNOOZE ] button in normal display mode for approx. 3 seconds to switch from ‚bright‘ to ‚middle‘.
Repeat step 1 to change the brightness level again as follows: from ‚middle‘ to ‚glimmer‘, from ‚glimmer‘ to ‚bright‘, …

The dimming function only works with the power adapter and after the device has received the DCF time signal. Once the DCF signal is received the LED brightness can be dimmed by pressing the Light/Snooze button for 3 seconds.

ENERGY-SAVING MODE

The alarm clock works in energy-saving mode when batteries are used for power supply. In this mode the LED will not light continously but can be activated for approx 1 minute by a push on the SNOOZE/LIGHT button. Also, the brightness of the LED display can not be changed.

DATE AND TEMPERATURE DISPLAY

Automatic display change
The default setting is set to automatic display change. The display switches every 10 seconds (current time) or rather every 3 seconds (date and temperature).

Manual display change
Press the MODE button in manual display mode to display the desired value. First disable automatic display mode:

Press and hold MODE button in normal time mode for approx. 3 seconds. Symbol ON flashes.
Press or button to select OFF.
Press the MODE button again to save the settings.

WARRANTY & SERVICE

The regular guarantee period is 5 years and beginson the day of purchase. You can consult thefull guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms.

Errors and technical changes reserved.
Manual_8020401000000_MyTime-W_de-en_BRESSER_v012021a

Bresser GmbH
Gutenbergstr. 2 · DE-46414 Rhede
Germany
www.bresser.de ·
service@bresser.de