PIMA DPP143 DPS Standard-Pet Immune Wireless PIR Motion Detectors Instruction Manual
- June 6, 2024
- PIMA
Table of Contents
- PIMA DPP143 DPS Standard-Pet Immune Wireless PIR Motion Detectors
- PARTS DESCRIPTION
- Coverage pattern
- MOUNTING
- Installation Instructions
- Technical specifications
- Mounting considerations
- How to install the DPS/DPP
- The LED
- How to test the detector
- Battery
- Limited Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PIMA DPP143 DPS Standard-Pet Immune Wireless PIR Motion Detectors
PARTS DESCRIPTION
Coverage pattern
MOUNTING
Surface mount
Corner mount Cover placing
Installation Instructions
The DPS (Standard) and the DPP (Pet immune) are wireless PIR (Passive Infra-
Red) motion detectors in FastLink technology, designed for the FORCE Series
and VISION intruder alarm systems. Using the DPS/DPP in FORCE requires the
installation of a wireless receiver.
The two detectors are based on digital processing, and utilize an advanced
movement detection algorithm. The DPS and the DPP can be used in apartments,
private houses and also in offices.
The DPP is immune to animals weighing up to 25 kilograms.
The DPS and the DPP have an elegant design. When detecting a movement the
detectors transmit an alarm signal to the control panel. The detectors have a
tamper switch that alerts when their enclosure is opened or removed from the
wall.
The DPS and the DPP transmit a supervision event when replacing the battery
and also every 15 min. The two detectors alert on low battery condition. For
enrollment information, see the alarm system’s Installation guide.
Cautions: the DPS and the DPP are based on wireless (RF) transmissions. Any wireless transmission can be subject to RF interference and, although unlikely, this interference may cause the DPS and the DPP to not operate as intended. RF transmissions will be attenuated by tinted glass, in wall isolation with metal foils, metal objects, etc.
Technical specifications
Frequency (MHz) | Models |
---|---|
One-Way | Two-Way |
433.92 | DPS/DPP143 |
868.95 | DPS/DPP187 |
- Sizes: 11 X 5.5 X 5.5 cm
- Weight: 110gr
- CE Compliance
- Temperature: -10 to +50 °C
- Battery: 1X CR123A, 3VDC, Lithium
- Battery Life: Up to Five Years (Typical Usage)
- Humidity (Max.): up to 93% R.H.
- Non-condensing
Content of the product package
- DPS/DPP detector
- Screws, mounting tapes
- This guide
Mounting considerations
- Surface or corner mount the detectors at a height between 1.8m and 2.5m.
- Allow the widest possible angle for the detector’s coverage pattern.
- Mount the detector where an intruder will most likely cross through the coverage pattern; the DPS and DPS detection range is 10m at 90 degrees.
- Do not mount the detectors outdoors or where direct sunlight can reach it.
- Do not mount the detectors where there are extreme levels of heat and light from heaters and air conditioners, hot and cold drafts, lightning, and moving headlights.
- Do not mount the DPP detector where pets can climb into the upper field of view.
How to install the DPS/DPP
- Release the screw at the bottom of the detector and remove the cover.
- Break the matching knock outs on the backplate for surface or corner mount; see the figures above.
- Fix the backplate onto a flat surface.
- Place the battery. Observe polarity!
- Set the jumpers; see below.
- Reassemble the detector: tilt it upwards, push it against the top part of the backplate first and then push the rest of it; see the Cover placing figure above.
- Fasten the detector’s screw.
- Enroll the detector (refer to the FORCE’s Installation guide).
- Test the detector using the Test and Diagnostics menu.
The LED
All models | Two-way (“Walk test”) |
---|---|
Color and state | Description |
Reception (RSSI)**
Green 1 blink| Battery OK, tamper closed.| | Green 2 blinks|
Good
Red 1 blink| Battery OK, tamper open.| | Green 3 blinks|
Excellent
Red 2 blinks| Low battery| | Red 3 blinks| Poor
The jumpers
Label| Jumper closed (on)| Jumper open (off)| Models
243/287
---|---|---|---
LED| The LED illuminates| The LED stays off|
SENS| Low sensor sensitivity (8m)| High sensor sensitivity (10m)| Not in use
(set by the control panel)5
PULSE| Alarm signal will only be transmitted, if two pulses are detected.|
Alarm signal will only be transmitted, if three pulses are detected.
How to test the detector
To test the detector, tamper it by opening its cover. The detector transmits a tamper event and enters into test mode for five minutes. During this time the LED will flash once on every detection (even if the LED jumper is in off position).
Sleep time
After transmitting a detection event, the detector will not transmit any
detection event for that time (unless it is in Test mode).
In models 143/187 sleep time is three minutes; in models 243/287 sleep time is set by the control panel5.
Battery
The detector is powered by a 3V, CR123A Lithium battery. The battery’s life
cycle is up to five years, with an average of 20 detections per day. Before
installing a new battery, press the enrollment button three times to discharge
excess power. After replacing the battery the detector warms up for one minute
and goes into test mode for five more minutes.
Low battery condition is detected when the battery voltage drops below 2.6V.
After that the battery can last for up to one month.
Ordering information
Model | One-way | Two-way | Model | One-way | Two-way |
---|---|---|---|---|---|
DPS | · 143: 8831010 |
· 187: 8831024
| · 243: 8831210
· 287: 8831224
| DPP| · 143: 8831012
· 187: 8831025
| · 243: 8831212
· 287: 8831225
Limited Warranty
PIMA Electronic Systems Ltd. does not represent that its product may not be
compromised and/or circumvented, or that the Product will prevent any death,
personal and/or bodily injury and/or damage to property resulting from
burglary, robbery, fire or otherwise, or that the Product will in all cases
provide adequate warning or protection. The User understands that a properly
installed and maintained equipment may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a
guarantee that such will not occur or that there will be no death, personal
damage and/or damage to property as a result.
Read this guide in its entirety before attempting to program or operate your
system. Should you misunderstand any part of this guide, please contact the
supplier or installer of this system.
Copyright 2020 PIMA Electronic Systems Ltd. All rights reserved. E&OE
Manufactured by
PIMA Electronic Systems Ltd.
www.pima-alarms.com
5 Hatzoref Street, Holon 5885633, Israel Tel: +972.3.6506414
Fax: +972.3.5500442
Email: support@pima-alarms.com
P/N: 4410448
4410448
Revision: C1, XX multi, Dec 2020
References
- Alarms.com
- Pima Electronic Systems | Residential & Commercial Security Systems
- Pima Electronic Systems | Residential & Commercial Security Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>