EKEN PASO 1080P Wire-Free Battery Camera User Manual
- June 6, 2024
- EKEN
Table of Contents
EKEN PASO 1080P Wire-Free Battery Camera
Features
- Wide-angle Lens
- . Indicator Lights
- Microphone
- Motion Sensor
- Light Sensor
Red Indicator Light AND Blue Indicator Light
- Flashing red
- Wi-Fi connection
- Blue light
- Live view
- Flashing blue
- Motion detection
In the box
- Paso Battery Camera
- Rechargeable 6000mAh Battery Pack
- Solar Panel +Mounting arm
- Stand
- Anchor Packs
- Screw Packs
- User Manual
Charge the battery
Charge the included battery.
Fully charge the battery by plugging it into a USB port using a Micro USB
cable.
It takes about 6-8 hours for the battery to fully charge. When only one blue
LED is lit, that indicates the battery is fully charged.
Set up your Paso
Remove the battery cover.
Push the battery cover backward to unlock, and then remove it from your Paso.
Insert the battery.
Insert the fully charged battery into the bottom of your Paso until it clicks
into place.
Set up your device in the Aiwit app. Before You Start
- Download and install Aiwit App. Scan the QR code below or search for Aiwit on the Apple App Store or Google Play. Download and install the app.
- Create an Aiwit account.
Set up your Paso in the Aiwit app. To pair your Paso, follow the steps below and in-app instructions.
- Open Aiwit App and log in to your account.
- To add your camera, select the+ icon.
- Select Battery Camera 2.
- Press and hold the Setup Button until the red light is flashing.
- Enter your 2.4GHz Wi-Fi network and the Wi-Fi password, then tap Next (5GHz is not supported).
- . Use your Paso camera to scan the QR Code shown on the app, then select Confirm once the Wi-Fi setup has -finished.
Install the Paso on a wall:
- Attach the stand to the camera.
- Secure tightly with the stand screw.
- Mark drill holes and use a bit to drill holes in your wall or ceiling. Insert anchors and secure your Paso with mounting screws.
- Screw the device with bracket to the base.
Need help setting up?
If you experience some issues during the app setup, try these steps:
- Check your WiFi password.
- The most common issue during setup is incorrect Wi-Fi passwords. Passwords are case sensitive.
- Pleasedouble-check your password.
- Reboot the router/modem.
- If you have entered the correct password, but still experiencing issues, try unplugging the power to your router/modem. Wait for 30 seconds, then plug the power back and turn it back on. Proceed to setup again in the Aiwit app.
Frequently asked questions
How long do my videos stay in my account?
Your videos are stored in the Free Cloud for up to 7 days.
How to RESET network settings
Press and hold the Setup Button until red light is flashing. Follow the in-app
instructions to finish your Wi-Fi setup.
How to share the device with my family
Open the Aiwit app. From the home page, tap the Share icon. Tap Share via
Email or Share via QR Code. You can share the device with up to 8 users.
Share via Email:
The new user has to download the Aiwit app and create an account with the same
email address which the device owner has shared with. Log in to the account
and you’ll see the shared device.
Share via QR Code:
- Open the Aiwit App on a new user’s smartphone.
- From the home page, tap +.
- Tap QR Code Sharing, then scan the QR code the device owner generated before.
- You will see Share successful, then tap Confirm.
How many users can view the video at the same time?
Up to 3 users may view the video feed, but only 1 user can use the direct
intercom. Both iOS and Android are compatible.
Is 5GHz Wi-Fi supported?
No. Only 2.4GHz Wi-Fi is supported.
Why is my Wi-Fi signal poor on my device?
Your device may be too far away from your wireless router or you may have some
obstructions in between that reduce signal strength. You might try
repositioning your router or getting a signal extender/repeater for your
wireless router.
How to adjust Motion Detection Sensitivity
From the home page, tap Motion Detection icon.
Motion Detection Sensitivity
- Fast: Records and notifies you about every motion. Shortest battery life.
- Medium: Records and notifies you about motion less often. Standard battery life.
- Slow: Records and notifies you about motion even less often. Maximum battery life.
How to enable Notifications on my phone
To do this, you need to give permission for the Aiwit app to access to your
microphone and enable notifications. Follow these steps to enable
notifications.
- Open Settings. Go to Aiwit app permissions and select Notifications.
- Make sure all switches are on.
Install your Solar Panel
Please complete the battery camera setup in the App prior to installing the solar panel.
Choose the installation location
Pick an unshaded spot for best sun exposure. The solar panel should be
installed where it will receive several hours of direct sun daily.
Mark your spot
Place the solar panel mounting arm mark where you plan to install, and mark
the screw hole positions lightly with a pencil. Drill the holes
Optional: You may opt to use a drill bit to drill the holes where you have
previously marked.
For mounting surfaces that are brick, concrete, or stucco, please use the
plastic anchors. You may need to use a hammer to install the anchor For
mounting surfaces that are wood or vinyl, you can omit the anchors, and use
the screws directly.
Install the mounting arm
Use a screwdriver to secure the mounting arm to the wall, tighten securely.
Attach the solar panel
Attach the solar panel onto the mounting arm, ensure that it is installed
correctly.
Note : You may adjust the angle of the solar panel for better sun
coverage. Simply loosen the adjustment screw on the mounting arm, adjust to
desired angle, and re-tighten the screw. Plug the cable
Lastly, plug the solar panel charging cable into the Asrtro. Let’s start
charging!
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Caution : Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>