3M CONSTRUCTION 7-5905-4 Quiet Space Headphones User Guide
- June 6, 2024
- 3M CONSTRUCTION
Table of Contents
Quiet Space™ Headphones
Quick Start Guide
-
Indicator light**
Off| Headphones off
---|---
White| Quiet Space™ mode
Blue| Bluetooth® mode
Red| Low battery
Yellow| Charging
Green**| Fully charged -
Mode button
On/Off
Press and hold for 3 second
Switching modes
Press to switch between Quiet Space™ and Bluetooth™ mode -
Volume controls
Press – to decrease volume and + to increase the volume
Action button
In Quiet Space™ mode
When the indicator light (1) is white, you are in Quiet Space™ mode Quiet Space™ mode provides three levels of sounds that are engineered to mask unwanted noises and allow you to get your work done
Press to cycle through low, mid, and high Quiet Space™ sounds
In Bluetooth® mode
Press to play/pause music
Quickly press twice to advance the track
Quickly press three times to skip back
For phone calls, press to answer or hang up; hold to decline an incoming call -
3.5 mm Audio Input
-
Microphone
For phone calls and teleconferencing
Getting Started
Auto Shut-off
Bluetooth®/Audio Input mode:
5 minutes after either Bluetooth® or the audio input is disconnected, the
headphone automatically powers down
Quiet Space™ mode:
After 4 hours of inactivity in Quiet Space™ mode, the headphone automatically
powers down
After Auto Shut-off, press and hold the power button for 3 seconds to turn the
headphones on
Pair Device
In Bluetooth® mode, press and hold the action button for 3 seconds You will hear “Bluetooth ® Pairing ” Make sure your Bluetooth ® enabled device is scanning/ searching for devices Check your device to make sure it has discovered 3M™ Quiet Space Select to connect to the headphones
Once Paired
Once paired, you will hear, “Pairing Successful”
Once Connected
Once connected, each time you turn on the headphones, it will automatically
link to your device and say, “Bluetooth® Connected”
Bluetooth® Range
The typical range between a Bluetooth ® enabled device and the 3M™ Quiet
Space™ Headphones is approximately 25 feet This distance depends on the device
As the distance between the Bluetooth ® enabled device and the headphones
increase the risk of the signal dropping also increases
For best results, keep the audio device on your body or within an arm’s length
of the 3M™ Quiet Space™ Headphones while using Bluetooth ® mode
Additional Info
Quiet Space™ mode
When the indicator light (1) is white, you are in Quiet Space™ mode. Quiet
Space™ mode provides three levels of sounds that are engineered to mask
unwanted noises and allow you to get your work done.
Bluetooth® mode
When the indicator light (1) is blue, you are in Bluetooth® mode.
To play your first song:
- Press and hold the action button (4) to pair a new device
- Select 3M™ Quiet Space Headphones in your device’s Bluetooth® menu
- Play a song from your favorite music app on your device
Voice and Video Calls
The integrated microphone lets you make and take phone calls hands-free. Quiet
Space™ Headphones are compatible with most video-conferencing platforms
Charging
To comply with the regulatory guidelines, your headphones have been shipped to
you with only a partial charge on their integrated lithium-ion battery.
To charge the headphones
Insert the supplied USB-C connector cable into the USB-C jack located on the
bottom of the left cup of the headphones.
Connect the other end of the cable to a suitable USB-C +5 Volt power source
such as a computer or third party certified (UL, Intertek, etc.) AC to USB-C
+5 Volt wall adapter.
The indicator light will be yellow while charging and change to green when
complete Product takes approximately 4 hours to charge fully
Note: Do not attempt to use the product while charging or while the
charging cable is connected
IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B).
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment.
Safety & Warnings
Safety Information
Please read, understand, and follow all safety information contained in these
instructions prior to the use of these 3MT” Quiet SpaceTM Headphones. Retain
these instructions for future reference.
Intended Use
3M’ Quiet SpaceTM Headphones are intended to mask background distractions in
home and office environments, and low to moderate noise environments. 3M”
Quiet Space” Headphones are not hearing protectors and are not intended to be
used in loud noise environments. Use in any other application has not been
evaluated by 3M and may lead to an unsafe condition.
EXPLANATION OF SIGNAL WORD CONSEQUENCES
**WARNING:| Indicates a hazardous situation that, if not avoided,
could result in serious injury or death.
CAUTION:**| Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury and/or property damage.
**WARNING
To reduce the risks associated with fire and explosion:**
- Do not wear the product while charging the battery.
To reduce the risks associated with an explosion:
- Remove headphones immediately if you experience a warming sensation or unexpected loss of audio.
To reduce the risks associated with hazardous voltage and fire:
- Only charge using a 3rd party certified (such as UL, Intertek, etc.) +5Volt USA power source.
- Only charge the device with a 3rd party certified charging cable.
- Do not immerse in water. Do not use in rain or other damp conditions.
- Do not disassemble, modify, or service the device. The unit contains no user-serviceable parts.
- Never use this product, or charge batteries, in an explosive or hazardous environment.
- Discontinue use if the product is damaged, not working correctly, or is exposed to water or moisture.
To reduce the risks associated with fire:
-
Do not store the headphones in direct sunlight or at temperatures above 131°F (55°C).
For example, behind a windshield or in a window. -
With Lithium-ion batteries, there is a risk of fire and burns. Do not open, crush, heat above 131°F (55°C), or incinerate.
-
Do not charge batteries in temperatures above 113°F (45°C).
To reduce the risks associated with hazardous noise:
- Do not use the product as hearing protection
To reduce the risks associated with reduced situational awareness:
- Stay alert and adjust the audio volume to the lowest acceptable level. Product may reduce your situational awareness and ability to hear warning signals. The audibility of warning signals at a specific workplace may be impaired.
- Do not use headphones at any time the inability to hear surrounding sounds may present a danger to yourself or others (e.g. driving a vehicle or riding a bicycle or walking in or near traffic, a construction site, or a railroad).
- Follow all applicable local laws and regulations regarding headphone use.
CAUTION
To reduce the risks associated with environmental contamination: Dispose of
electronic waste in accordance with local laws and regulations.
NOTICE
To prevent damage to the device:
- Clean with a dry cloth only. Do not use harsh or abrasive chemicals.
- For best performance, the ear cushions should seal firmly against your head. Anything that interferes with the seal such as long hair (pull back to the extent possible), thick or poorly fitting eyeglass temples, pencils or caps will lessen the product performance.
- Do not bend or reshape the headband.
IMPORTANT SAFETY INSTRUCTIONS
This product contains magnetic material. Consult your physician on whether
this might affect your medical device.
FCC REGULATORY CONFORMANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Unauthorized modifications may void the authority granted under Federal Communication Rules permitting the operation of this device. Modifications to this device shall not be made without the written consent of 3M Company.
RF Exposure:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
FCC ID: 2AFHL-QUIET
QuietSP-SIOC
34-8727-5905-4
© 2021, 3M. All rights reserved. 3M and Quiet Space are trademarks of 3M. The
Bluetooth® word mark and logo are registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by 3M is under license.
Dist. by: 3M Company, 3M CENTER ST. PAUL, MN 55144-1000
1-800-537-2191
651-737-6501 MADE IN CHINA.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>