Continal 39015-WCEX Quantum Wiring Extension Instruction Manual
- June 6, 2024
- Continal
Table of Contents
Quantum wiring extension+
Simple to operate and easy to install, our Quantum wiring extension increases
the capabilities of your Quantum wiring centre.
This plug-in unit allows you to attach up to 4 more thermostats using simple
push-in connectors. Super-clear LED indicators keep you in the picture.
Contents
- Wiring centre description
- Serial connector
- Power supply
- LED indicators
- Night set back
- Actuator connection
- Thermostat connection
- Installation
- Product compliance and safety information
Wiring centre description
- Serial connector
- Power supply
- Connection indicator
- Power indicator
- NSB function terminals
- Actuator connection
- Thermostat connection
Serial connector
The serial connector is used to connect the Quantum wiring centre with the Quantum wiring extension to add functionality and support up to 12 zones.
Power supply
The power supply for the wiring centre is 230VAC.
Two-wire installation should be made in accordance with the applicable
regulations.
LED Indicators
Connection indicator
After the successful connection of the Quantum wiring centre with the
Quantum wiring extension, the extension module LED will light up red
constantly.
Power indicator
After the connection of the Quantum wiring extension to the power supply,
the red power LED will light up.
5. Night setback
NSB function is activated in non-programmable Continual thermostats via an external signal. NSB 230VAC signal (night-time temperature reduction) is sent via an external timer r programmable thermostat connected to the wiring centre. Non-programmable thermostats receive NSB signal and reduce setpoint temperature (by switching to eco-mode). All thermostats have to be connected using a 4-wire cable (min. 4 x 0.75mm 2 , max. 4 x 1.5mm 2 ).
One Master thermostat that is common for thermostats from Group 1, Group 2 and Group 3 (one programmable thermostat and other thermostats are nonprogrammable).
Three Master thermostats. One for Group 1, one for Group 2 and one for Group 3 (three programmable thermostats, other thermostats are nonprogrammable). One external clock that is common for thermostats from Group 1, Group 2 and Group 3 (one external clock + daily regulators). Three external clocks. One for Group 1, one for Group 2 and one for Group 3 (three external clocks + nonprogrammable regulators).
Note: Terminals 1-4 and 5-8 are located in the Quantum wiring centre, while terminals 9-12 are located in the Quantum wiring extension module.
Actuator connection
The actuator wires should be secured with the self-locking connectors in the
appropriate zone. Up to 6 actuators with a load of up to 2 watts each can be
connected to a single zone. If you need more than 6 actuators in a single
zone, use an additional relay to relieve the output.
Note: 230VAC voltage when actuators are live.
Thermostat connection
Connecting a 230VAC thermostat
Connecting an ON / OFF battery-powered thermostat with voltage-free COM / NO
output contacts.
Note: In the NSB product series follow interchangeable signifying:
↑ = SL
= NSB
Installation
Remove the top cover of the wiring centre extension and unscrew the main housing.| Mount the backside of the housing to the wall. When mounting on a DIN rail, open the hooks on the back of the housing.
Remove the appropriate piece of insulation from the wires.
Thread the wires under the mounting bolt in the back part of the wiring centre
extension.| Thread the wires through the slots in the top part of the wiring
centre extension and connect it to the terminals.
Adjust the wires and screw the main housing of the wiring centre extension to
the rear housing.| Connect the actuator’s wires.
Connect the serial cable to the Quantum wiring centre and the Quantum wiring
extension connector.| Make sure that all wires are properly connected, then
mount the top cover and power up the wiring centre and wiring centre
extension. “Power” and “Connection” red LED will light up indicating the
correct connection with the Quantum wiring centre.
Product compliance and safety information
Product compliance
This product complies with the essential requirements and other relevant
provisions of the following EU Directives: EMC 2014/30/EU, Low Voltage
Directive LVD 014/35/EU and RoHS directive 2011/65/EU.
Safety information
Use in accordance with national and EU regulations. The device is intended for
indoor use only in dry conditions. Installation must be carried out by a
qualified person in accordance with national and EU regulations.
Before attempting to set up and install, make sure that the devices are not connected to any power source. Installation must be carried out by a qualified person. Incorrect installation may cause damage to the devices. The Quantum wiring extension should not be installed in areas where it may be exposed to water or damp conditions.
Want more information?
04 80 28 01 02
www.continal.fr
Rev:07/21
© 2021 Continual Group Ltd. All rights reserved. E & OE.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>