HENDI 222157 Stick Blender User Manual

222157 Stick Blender
User Manual

You should read this user manual carefully before using the appliance.

Keep these instructions with the appliance.

For indoor use only.

Dear Customer,

Thank you for purchasing this Hendi appliance. Read this manual carefully, paying particular attention to the safety regulations outlined below, before installing and using this appliance for the first time.

Safety regulations

• This appliance is intended for commercial use.
• Only use the appliance for the intended purpose it was designed for as described in this manual.
• The manufacturer is not liable for any damage caused by incorrect operation and improper use.
• Keep the appliance and electrical plug away from water and other liquids. In the event, the appliance falls into water, immediately remove the power plug from the socket. Do not use the appliance until it has been checked by a certified technician. Failure to follow these instructions will cause life-threatening risks.
• Never attempt to open the housing of the appliance by yourself.
• Do not insert objects into the housing of the appliance.
• Do not touch the plug with wet or damp hands.
• The danger of electric shock! Do not attempt to repair the appliance by yourself, repairs are only to be conducted by qualified personnel.
• Never use a damaged appliance! When it’s damaged, disconnect the appliance from the socket and contact the retailer.
• Warning! Do not immerse the electrical parts of the appliance in water or other liquids.
• Never hold the appliance under running water.
• Regularly check the power plug and cord for any damage. When damaged it must be replaced by a service agent or similarly qualified person in order to avoid danger or injury.
• Make sure the cord does not come in contact with sharp or hot objects and keep it away from an open fire. Never pull the power cord to unplug it from the socket, always pull the plug instead.
• Make sure that the power cord and/or extension cord do not cause a trip hazard.
• Never leave the appliance unattended during use.
• Warning! As long as the plug is in the socket the appliance is connected to the power source.
• Turn off the appliance before unplugging it from the socket.
• Connect the power plug to an easily accessible electrical socket so that in case of emergency the appliance can be unplugged immediately.
• Never carry the appliance by the cord.
• Do not use any extra devices that are not supplied together with the appliance.
• Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
• Never use accessories other than those recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
• This appliance should not be operated by persons with reduced physical, sensory or mental capabilities, or persons that have a lack of experience and knowledge.
• This appliance should, under any circumstances, not be used by children.
• Keep the appliance and its power cord out of reach of children.
• WARNING: ALWAYS switch off the appliance and unplug from the power socket before cleaning, maintenance, or storage.

Special Safety Regulations

• Use the appliance only as described in this manual. Indoor use only.
• This appliance should be operated and installed by specialized trained personnel in the kitchen of the food industry such as catering, restaurants, bars, etc.
• All maintenance, installation, and repair works should be performed by specialized trained authorized technicians.
• Keep the appliance away from hot surfaces and open flames. Always operate the appliance on a level, stable, clean, heat-resistant, and dry surface.
• Wear protective clothing, mask, or protective glasses if necessary during operation.
• This appliance is not intended to be operated by means of an external timer or separate remote-control system.
• WARNING: Keep all ventilation openings in the appliance clear of obstruction.
• WARNING: During operation, keep hands and utensils out of the container to reduce the risk of severe personal injury and/or damage to the blender.
• Allow at least 20 cm spacing around the appliance to avoid danger.
• Caution! Securely route the power cord if necessary in order to prevent unintentional pulling or contact with the moving blade.
• Do not immerse the shaft into the water or liquid less than 5cm.
• Do not continuously operate the appliance to avoid overheating the motor. The continuous operation time should not exceed over 3 minutes. Operate the appliance again, after it has been cooled.
• Do not use the machine outside the container.
• Do not touch the blade, blade guard, and moving parts. Keep fingers, hair, clothing, and utensils away from all moving parts.
• Do not wash the appliance with water or waterjet. Washing with water can cause leakage and increase the risk of electric shock. No parts are dishwasher safe.
• To avoid damaging the cord, do not squeeze, bend or chafe it on sharp edges. Keep it away from hot surfaces and open flames as well. Do not let rotating blades touch the power cord.
• Layout the power cord in such a way that no unintentional pulling or tripping over is possible.
• Do not clean or store the machine unless it is completely cooled down.
• The danger of injury! Care should be taken when handling the sharp cutting blades during cleaning.
• This appliance is classified as protection class II.

Intended use

• This appliance is intended for professional use.
• This appliance is solely intended for crushing, mixing, mashing, and pureeing suitable soft ingredients in a container. Any other use may lead to damage of the appliance or personal injury.
• Operating the appliance for any other purpose shall be deemed a misuse of the device. The user shall be solely liable for improper use of the device.

Main parts of the appliance

1. ON/OFF switch : Press and hold for continuous operation; Release the button to stop operation
2. Increase speed setting +: Increase speed between 1 to 6
3. Decrease speed setting -:  Decrease speed between 1 to 6
4. LCD display: To show the speed setting
5. Handle
6. Ventilation holes
7. Detachable blending part
8. Blade
9. Blade guard
10. Main unit with motor

Preparations before operation

• Remove all protective packaging and wrapping.
• Check the appliance for completeness and transport damages. In case of incomplete delivery or damaged, contact the supplier immediately. DO NOT use the appliance. (See ==> Warranty).
• Clean the appliance before use (See ==> Cleaning and Maintenance).
• Make sure the appliance is completely dry.
• Preparation of the food ingredients for processing.

Before operation

• Read this manual thoroughly and carefully before operation.
• Ensure the appliance is placed in a dry area without any obstacles to block your operation.
• Check to ensure the electrical power supply corresponds with the rating label on the appliance.
• Make sure the blending part (7) is installed firmly with the main body with the motor part (10).

Transportation

• Do not move the appliance while it is under operation. Unplug the appliance when moving to another place.
• Hold the handle part of the appliance when moving away.

Operation

Observe the following safety advice at all times!

• Always ensure the appliance is disconnected from the power supply before it is assembled with the blending part (7).
• Never put your hands into the food container (not supplied). Always use wooden or plastic spatulas, and only when the appliance is not running.
• Do not operate the appliance with no foodstuff inside the container or with hard foods, hot liquids, heavy dough, etc. in order to prevent overheating.
• WARNING! Unplug the appliance immediately after use.

Assembling / Disassembly of the attachments

The assembly/disassembly operations of the appliance are performed with the appliance stopped and disconnected from the power supply.

Main unit (10) and blending part (7):

Disassembly:

1. Hold the main unit (10) and screw out the blending part (7) by clockwise until it is fully detached.

Assembly:

1. Align the coupling of the blending part (7) to the clutch of the main unit (10).
2. Screw-in the blending part (7) anti-clockwise until it is fully tightened.

Blending part (7) and blade (8):
CAUTION! Please wear protective gloves for disassembly (not included).

Disassembly:

1. Hold the coupling of the blending part (7) and screw out the blade (8) anti-clockwise until it is fully detached.
2. Hold the blending part (7) and pull out the shaft.

Assembly:

1. Insert the shaft into the blending part (7) until it is fully inserted.
2. Hold the coupling of the blending part (7) and screw in the blade by clockwise until it is fully tightened.

Suitable for:| • Blending juices and shakes
• Mixing soft ingredients (e.g. pancake batter or mayonnaise).
• Mixing vegetables into soup (e,g. carrots, etc.)
---|---
Preparation:| • Peel or pare food and cut them into small chunks.
• Place the food into a suitable container of capacity 1~4 liters.
Maximum continuous operation time| 3 minutes to prevent motor overheating. Operate the appliance again after cooling down.

• Once connected to the power plug, “3” will be shown on the LCD display (4).

• Lower the blending part (7) into the food container (not supplied). Fully submerge blade (8) into the ingredients before starting the appliance.
  ATTENTION:
  You should not submerge the blending part (7) above the Max. mark.

• Hold the main unit (10) firmly with one hand and the mixing container with the other hand.
  Press and hold the ON / OFF button (1), the appliance then starts blending continuously.

• Use a gentle up-and-down motion to blend the food ingredients smoothly.
  To avoid food spattering, do not lift the appliance out of the ingredients during operation.

• Select the blade speed by pressing the + (2) or – (3) button (Speed range: 1 to 6) during operation. The blade speed will be shown on the LCD display (4). Note: No need to
  Press the ON/OFF button (1) when selecting the blade speed simultaneously.

• After finishing the operation, release the ON / OFF button (1) to switch off the appliance.

• Wait until the blade (8) stops completely. Then, unplug it from the electrical supply.

• Turn the main unit (10) clockwise to disassemble the blending part (7) for cleaning.

Note:

1. Press and hold the decreasing and increasing button + (2) or – (3)  button for fast adjustment.
2. The default blade speed will be set to “3” once plugin.

Cleaning and Maintenance

Attention: Always unplug the appliance from the electrical power outlet and let it cool down completely before cleaning and disassembly the blending part (7).

Cleaning

• Remove all obstacles near the blade.
• Place the blending arm and the bell in a suitable container with clean water and switch it on for a few seconds. Never immerse the shaft above the Max. mark.
• Never immerse the motor unit or the handle in water; clean with a damp cloth or a sponge.
  WARNING: Always dry the blades thoroughly after cleaning to avoid rust spots.

Recommended cleaning procedure:

liquids.
• Using a damp cloth with some detergent and water, rinse, sanitize and dry thoroughly.| Clean after each use
Blending part (7)| • Clean it with warm water and some mild detergent. Do not submerge the Detachable blending part (7) above the Max. mark.
• Dry all parts before using them again.
Blade (8)| • Warning! Risk of injury! Take great care when cleaning the blades.
• Clean it with warm water and some mild detergent.
• Dry it thoroughly after cleaning.

Storage

• Before storage, always make sure the appliance has already been disconnected from the electrical outlet and cooled down completely.
• Store the appliance in a cool, clean, and dry place and keep it out of reach of the children.

Troubleshooting

If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider.

connected to a suitable electrical outlet property.
ON/OFF button 111 is not pressed.| Press and hold the ON/OFF button (1) to switch on the appliance.
Abnormal noises while pro-cessing| The blending part 17) is not connected correctly.| Disassembly and assembly of the blending part (71 again.
The appliance cannot operate| Inside overheated devices activate.| Let the appliance coot down completely before starting operation again.
Appliance is overheat| Overtime operation| Release the ON/OFF button and unplug the device, wait 10 minutes for the motor to cool down.

Technical specification

Item no.: 222157
Operating voltage and frequency: 230V~ / 50Hz
Rated input power: 250W
Protection class: Class II
Waterproof protection class: IP23
Dimension: approx. 71 x 71 x (H) 444 mm
Net weight: approx. 1,6kg
Rotation speed (rpm): approx. 6,600 to 13,500
Noise level: < 85dB(A)
Remark: Technical specification is subjected to change without prior notification.

Part list for 222157

Circuit diagram

Warranty

Any defect affecting the functionality of the appliance which becomes apparent within one year after purchase will be repaired by free repair or replacement provided the appliance has been used and maintained in accordance with the instructions and has not been abused or misused in any way. Your statutory rights are not affected. If the appliance is claimed under warranty, a state where and when it was purchased and include proof of purchase (e.g. receipt). In line with our policy of continuous product development, we reserve the right to change the product, packaging, and documentation specifications without notice.

Discarding & Environment

When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose to your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment, and ecological disposal, either directly or through a public system.

Innovatielaan 6, 6745 XW De Klomp
The Netherlands
Tel: +31 317 681040
Fax: +31 317 681045
www.hendi.eu
info@hendi.eu

Declaration of conformity

Hindi BV hereby declares under his own responsibility that the product:
Product number: 222157
Product name: Stick blender
Brand: Hindi
Meets the essential requirements as described in : 2006/42/EC
2014/30/EU
2011/65/EU & 2015/863/EU
Has been engineered and manufactured in conformity to harmonized standards:
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 12853:2001+A1:2010
EN 60204-1:2006+A1:2009/AC:2010
EN ISO 12100:2010
Meets the requirements as described in regulations: 1907/2006/EC
Meets the requirements as described in resolutions: CM/Res(2013)9
Technical documentation available at the company’s headquarters:
Hindi B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands

Hendi B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands
Tel: +31 317 681 040
Email: info@hendi.eu

H endi Polska Sp. z o.o.
ul. Firmowa 12
62-023 Robakowo, Poland
Tel:
+48 61 658 7000
Email: info@hendi.pl

Hindi Food Service Equipment GmbH
Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 6274 200 10 0
Email: office.austria@hendi.eu
Hindi Food Service Equipment Romania S.R.L.
Str. 13 Decembrie 94A, Hala 14
Brașov, 500164, Romania
Tel: +40 268 320330
Email: office@hendi.ro

PKS Hendi southeast Europe SA
5 Metsovou Str.
18346 Moschato, Athens, Greece
Tel:
+30 210 4839700
Email: info@pks-hendi.com

– Changes, printing, and typesetting errors reserved.
© 2021 Hendi B.V. De Klomp – The Netherlands

References

• hendi.com
• hendi.com
• Welkom - HENDI Tools for Chefs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>