SWIT CURVE500 TX Wireless Video Transmission User Manual

SWIT CURVE500 TX Wireless Video Transmission User Manual

Preface

• All internal technologies of this product are protected, including device, software and trademark.
  Reproduction in whole or in part without written permission is prohibited.

• All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners.

• Due to constant effort of product development, SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice.

• The warranty period of this product is two years, and does not cover the following:
  (1) Physical damage to the products
  (2) Any damage or breakdown caused by use, maintenance, or storage not according to the user manual’s introductions.
  (3) The attenuation of signal quality resulting from being used in any special environments.
  (4) Any damage caused by not powering the product by package supplied power adaptor.
  (5) Any damage or breakdown not caused by the product’s design, workmanship, manufacturing, quality, or unauthorized repairs or parts replacement or other operations.

• For any suggestions and requirements on this products, please contact us, please contact us through phone, fax, Email, etc.

SWIT Electronics Co., Ltd.

Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R. China
Tel: +86-25-85805753
Fax: +86-25-85805296
Email: contact@swit.cc
http://www.swit.cc

Safety Precautions

Please follow the safety precautions before using. The following conditions are not covered by warranty.

1. Unauthorized repairs or other Unauthorized operations.
2. Inappropriate placement including but not limited to lighting, fire, exposure to rain, water or gas.
3. Using the wrong power supply.

Packing list

1. Product Introduction

CURVE500 includes transmitter and receiver, adopts the latest encrypted transmission technology, Supports HDMI wirelessly transmitted in 150 meters scale{Line-of-sight), 1 channel HDMI digital video transmission, auto pairing. CURVE500 is equipped with DC power connector, compact size, portable,
and the receiving signal is very stable.

2. Features

• HDMI Wireless transmission
  Support up to 1080P50/60Hz HDMI wireless transmission.

• 150 meters transmission distance
  In open outdoor area, the effective transmission distance is approx. 150 meters (line of sight).

• Wireless frequency
  The system adopts 5180~5220MHz and 5760~5820MHz Wireless frequency band(CURVE500 Tx).

• Pairing mode
  Support auto pairing connection and manual switching of frequency points.

• Encryption
  Support AES 128-bit encryption to protect the transmission.

• All-Metal Shell
  Both the transmitter and receiver adopt metal shell which is durable and solid.

• All hardware design
  The wireless system is hardware and plug-and-play designed, without installing software, easy to set up.

Remark:

1. The transmission distance may be different, and depend on surroundings, radio wave conditions, buildings, etc., the 150 meters transmission distance may be not guaranteed.
2. The wireless transmission might be interrupted if there’ re other devices of 5GHz wireless bandwidth Used in the same location.
3. Signal reception may be affected by the position, height and angle of devices. If reception video is not stable, please physically adjust placement for the optimized signal.
4. Set the antennas straight up and set receiver higher to enhance the transmission efficiency.
5. The product offers the AES 128-bit encryption to protect the wireless transmission. Please still be aware of the intentional signal interception from third person. Do not use it for important communication.

3. Appearance Instruction

Transmitter CU RVES00

1. Antenna
2. Product label
3. Link: Wireless status indicator
4. Video: Video signal indicator
5. Power: Power status indicator
6. Pair：0.96-inch OLED
7. Installation thread：1/4”-20 thread. Use the package supplied articulating arm trestle to install the device to the camera.
8. USB： Micro USB, software upgrade interface
9. HDMI in： HDMI input (standard HDMI-A type connector).
10. Battery plate: “F” plates can be used. We recommend SWIT batteries like: S-8972, S-8970, S-8770, S-8975 compatible with SONY“ L” series NP-F770/970.
11. HDMI LOOP：HDMI loop out (standard HDMI-A type connector).
12. ON/ OFF: Power switch
13. DC in: Support DC 7～17V input,5.5mm(outer diameter)/2.1mm(inner diameter) Outside: negative, Inside: positive

Receiver CU RVES00

1. Antenna
2. Product label
3. Link: Wireless status indicator
4. Video : Video signal indicator
5. Power : Power status indicator
6. Pair : Pair button
7. Installation thread: 1/4″ -20 thread, Use the package supplied articulating arm trestle to install the device to the camera
8. USB : Micro USB, software upgrade interface
9. HDMI OUT: HDMI output (standard HDMI-A type connector).
10. Battery plate: “F” plates can be used. We recommend SWIT batteries like: S-8972, S-8970, S-8770, S-8975 compatible with SONY “L” series NP-F770/970/.
11. HDMI OUT: HDMI output (standard HDMI-A type connector).
12. ON /OFF: power switch
13. DC in : Support DC 7~17V input,5.Smm(outer diameter)/2.lmm(inner diameter) Outside: negative, Inside: positive

4. Setup connection

1. Connect the HDMI in interface of the CURVES00 transmitter to the HDMI out of the camera or video output device.
2. Connect the HDMI out interface of the CURVES00 receiver to the HDMI in of the monitor or switch station.
3. Connect the power supply of CURVES00 transmitter and receiver, the “power” indicator will light up, “Link” and “Video” indicator light up when the transmitter and receiver have identifiable signal inputs and connections, “Link” and “Video” indicator will flash if transmitter and receiver have no identifiable signal input

Tips:

1. Put the power switch to “ON” when connect the power supply of CU RVES00 transmitter and receiver.
2. The curve 500 transmitter only supports the HDMI video input interface, and the system automatically detects the input video interface

5. Pairing

1. Connect the HDMI in interface of the CURVES00 transmitter to the HDMI out of the camera or video output device.
2. Connect the HDMI out interface of the CURVES00 receiver to the HDMI in of the monitor or switch station.
3. Connect the power supply of CURVES00 transmitter and receiver, the “power” indicator will light up “Video” and “Link” indicator will flash.
4. Long pressing the “pair” button in both transmitter and receiver, The “Link” indicator of transmitter and receiver flash and pair, “Link” indicator lights up, the automatic pairing is successful and enters the encrypted transmission state.
5. Press the “Pair” button twice a partly to upgrade the firmware, the “Video” indicator quickly lashing during upgrade process, “Video” “Link” indicator light up with red, the firmware upgrade successfully. The “Video” “Link” indicator flash when upgrade is failure

Tips:

1. When pairing, the transmitter and receiver need to be paired Simultaneously.
2. During normal use, ensure that the wireless device used has been paired and successfully paired.
3. The paired transmitter and receiver will be automatically connected after booting up. It is no need to pair again.
4. Please keep the transmitter and receiver in distance of 1-2m to avoid pairing failure.

6. The way to get the best effective of Wireless Transmission

(1) Set the antenna on both transmitter and receiver vertically straight up. No request to spread. (Fig. 1)

7. Trouble shooting

If the receiver failed to output video correctly, the possible causes are as below; please find the solution from following chart:

8. Specification

FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

SWIT Electronics Co., Ltd.

Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R. China

Tel: +86-25-85805753
Fax:+86-25-85805296
Email: contact@swit.cc
http://www.swit.cc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>