audizio 102.418 Monza Stereo Radio Instruction Manual

: June 6, 2024
: audizio

audizio 102.418 Monza Stereo Radio Instruction Manual

Congratulations to the purchase of this Audizio product. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features.

Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

Safety Instructions

Prior to using the unit, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
The unit contains voltage carrying parts. Therefore do NOT open the housing.
Do not place metal objects or pour liquids into the unit This may cause electrical shock and malfunction.
Do not place the unit near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
The unit is not suitable for continuous use.
Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
When unplugging the unit from a mains outlet, always pull the plug, never the lead.
Do not plug or unplug the unit with wet hands.
If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
If the unit is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact your dealer. Do NOT connect the unit to a rheostat or dimmer.
To avoid fire and shock hazard, do not expose the unit to rain and moisture.
All repairs should be carried out by a qualified technician only.
Connect the unit to an earthed mains outlet (220- 240Vac/50Hz) protected by a 10-16A fuse.
During a thunderstorm or if the unit will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
If the unit has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the unit in humid rooms or outdoors.
To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.
Do not repeatedly switch the fixture on and off. This shortens the life time.
Keep the unit out of the reach of children. Do not leave the unit unattended.
Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
Do not force the controls.
This unit is with speaker inside which can cause magnetic field. Keep this unit at least 60cm away from computer or TV.
If this product have a built-in lead-acid rechargeable battery. Please recharge the battery every 3 months if you are not going to use the product for a long period of time. Otherwise the battery may be permanently damaged.
If the battery is damaged please replace with same specifications battery. And dispose the damaged battery environment friendly.
If the unit has fallen, always have it checked by a qualified technician before you switch the unit on again.
Do not use chemicals to clean the unit. They damage the varnish. Only clean the unit with a dry cloth.
Keep away from electronic equipment that may cause interference.
Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
Switch the unit off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the unit.
Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this unit.
Keep the original packing material so that you can transport the unit in safe conditions.

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.

The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit. This would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Audizio cannot be held responsible for personal injuries caused by a disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

PRODUCT OVERVIEW

LCD Display
On/Standby:
From Standby mode press the button to show Time, Date, Alarms, then press a second time to switch On.
Preset:
Press and hold to save a station as a preset, or press to recall a saved preset station.
Scan:
Press to scan DAB and FM stations
Prev :
To review station list (DAB), or go back 0.05MHz (FM), or previous track (BT).
OK/Volume
Rotate the Volume dial to increase/decrease the volume. Press the dial once to confirm current operation and snooze the alarm when sounding. In BT mode keeping the dial pressed will disconnect from your device. To reconnect to the same device just keep the dial pressed in again.
Mode:
Press to switch between DAB / FM radio / BT modes.
Info/Back
Press repeatedly to access station information. When in a sub-menu press to go back to a previous menu.
Menu
Press to display menu options.
Next
To review station list (DAB), or go forward 0.05MHz (FM), or next track (BT).
DC INPort
3.5mm Headphone Socket
Antenna

QUICK SETUP

Connecting the Power

Insert the power adapter into the DC IN port on your DAB Radio.
Insert the 3-pin adapter into a suitable mains socket

Using Your DAB Radio

Switching on your DAB Radio for the first time
Extend the telescopic antenna for the best reception possible.
Then press the POWER button to turn the radio on.
When DAB mode is activated for the first time, a full scan will automatically commence.
Once the radio be turned on, press the MODE button to switch between DAB , FM , BT modes.
During scanning the screen will display a slide bar that indicates the progress of the scan, and the amount of radio stations that have been found so far. Once the scan has finished, the radio will select the first alphanumeric station.
Press On/Standby button once to put the DAB Radio into Standby mode.

Press the [MODE] button several times to switch between input sources.

Description: Function

DAB: Radio Listen to a digital radio station.
FM: Radio Listen to an FM radio station.
BT: Listening to a BT device

CHARGING THE INFORMATION SHOW ON SCREEN

When listening to a digital or FM radio station, you can change the information that is displayed on the screen.

Digital radio

When listening to digital radio, press the Select dial to toggle the information displayed on screen between Scrolling text, Programme, Channel/ frequency, Signalstrength / error, Bitrate or Date.

When listening to digital radio, you can also press and hold the [INFO] dial to toggle the display to show the ‘Now playing’ screen, a full screen version of the radio station artwork and a screen that shows information about the show that is being broadcast along with the radio station artwork.

FM radio

When listening to FM radio, press the [Info] dial to toggle the information displayed on the screen between ‘Scrolling text’, ‘Programm type’, ‘Frequency’, ‘Stereo/Mono’ and ‘Date’.

LISTENING TO DIGITAL OR FM RADIO

Power

Press [POWER] button to turn on the DAB Digital Radio.

Changing digital DAB stations

Press the [MODE] button and turn and press the [OK/VOLUME] dial to select ‘DAB radio’ from the Home screen.
Press the or button for station list.
Press the or button or [OK/VOLUME] dial to select your favorite radio station.
Press the [OK/VOLUME] button to listen to your favorite radio station.

CHARGING FM STATIONS

Seek tuning

Press the [MODE] button several times to Select ‘FM radio’.
Press the or button FM radio station that has a strong signal.

USING RADIO PRESETS

You can store up to 30 digital radio and 30 FM radio stations for quick access.

To store a station to the preset list:

Tune to the digital or FM radio station you want to store.
Hold the [PRESET] button for at least 4 seconds to view the numerical list of stored presets, then turn and press the [OK/VOLUME] dial to choose any Preset number between 1 and 30. You can overwrite existing presets.

To recall a preset when listening to digital radio or FM radio

Push the [PRESET] button, turn the [OK/VOLUME] dial right or left to scroll through the list of presets, then push and release the [SELECT] dial to tune to the selected preset.

USING THE BT INPUT

Make sure the DAB Radio has been switched on. Press the MODE button to select BT mode, and the display will show “BT Disconnected”.
Enable BT on your Smartphone and search for BT connections, select “Audizio Monza” from the list of devices. If you are asked for a pass code enter “0000”.
When successfully paired, the display will show “BT Connected”.
Once you have paired the DAB Radio with a smartphone or BT device, it will remember this device and will pair automatically when the device’s BT is activated and in range, you do not need to re-pair any previously connected devices under BT mode.
The DAB Radio will attempt to automatically connect to the last device it was paired with if BT mode is turned on. If you want to pair it with a new device, please press the OK/Volume dial until the display shows “Disconnected” and then use your new device to search and select the pairing name.

SETTING ALARMS AND TIMERS, SNOOZE FUNCTION

Setting an alarm

Press and hold the [MENU] button to view the main menu and select ‘System’.
Turn and press the [OK/Volume] dial to select ‘Alarm’.
From the ‘Alarm’ menu, turn and press the [OK/Volume] dial to select either ‘Alarm 1’ or ‘Alarm 2’.
Select Alarm ‘ON of OFF’ by turning and pressing the [OK/ VOLUME] dial, turn the dial to adjust the hours and minutes, pressing [OK/Volume] to confirm each section.
Select frequency Once,daily,weekdays,weekend.by turning and pressing the [OK/Volume] dial, turn the dial to adjust the hours and minutes, pressing [OK/ VOLUME] to confirm each section.
Set the source by turning and pressing the OK/Volume] dial, turn the dial to adjust Buzzer,DAB or FM, pressing [OK/ Volume] to confirm.If you’ve chosen ‘DAB’ or ‘FM’ radio, turn and press the [OK/Volume] dial to select ‘Preset’. To play the station you last listened to, turn and press the [OK/Volume] dial to select ‘Last listened’ or turn and press the [OK/Volume] dial to choose a radio station from the preset list.
Turn and press the [OK/ Volume] dial to select ‘Volume’. Turn and press the [OK/ Volume] the dial to set the volume of the alarm.
Turn and press the [OK/ Volume] dial to select ‘Duration’. Turn and press the [OK/ Volume] to set the duration that the alarm will sound in minutes.

SNOOZING A SOUNDING ALARM

To snooze a sounding alarm, press the [OK/ VOLUME] dial. The display will show a countdown timer to show and the alarm will re-start again after 5 minutes on each press. To cancel a snoozing alarm press the [STANDBY] button.

Setting the sleep timer

Press the Menu button and turn and press the Select dial to select ‘System Settings’.
Turn and press the [OK/ Volume] dial to select ‘Sleep’.
Turn and press the [OK/ Volume] dial to adjust the length of the sleep timer.

Cancelling a sounding alarm

Press [STANDBY] to cancel any sounding alarm or press [SOURCE] to cancel and leave the radio on.

TIME AND SATE SETTINGS

The clock will automatically set itself using your digital radio signal. If the time or date does not update automatically, you can manually set it using this option.

Note: Any time or date updates received by a digital broadcast will override manual settings.

Setting the time and date manually

Press and hold the [MENU] button to view the mainmenu.
Turn and press the [OK/ Volume] dial to select ‘System settings’ > ‘Time’.
Turn and press the [OK/ Volume] dial to choose ‘Set Time/Date’.
Turn and press the [OK/ Volume] dial to set the hour. Repeat to adjust the minutes.
Turn and press the [OK/ Volume] dial to set the day of the month. Repeat to set the month and year.

Note: If you have set your the 12 hour time format, make sure that you select the ‘AM’ or ‘PM’ version of the hour before pressing the Select dial.

TIME AND DATE SYNCHRONIZATION OPTIONS

You can synchronize the time and date on the digital radio signal. To specify the clock synchronization options:

Press and hold the (MENU) button to view the main menu.
Turn and press the [OK/ Volume) dial to select ‘System settings’ D. ‘Time.
Turn and press the [OK/ Volume) dial to choose ‘time update.
Turn and press the [OK/ Volume) dial to choose ‘Auto update.

CHANGING THE TIME FORMAT

Press and hold the (MENU) button to view the main menu.
Turn and press the [OK/ Volume) dial to select ‘System settings’ > ‘Time’.
Turn and press the KO K/ Volume) dial to choose ‘Set 12/24 hour’.
Turn and press the [OW Volume) dial to choose between ’12’ or ’24’ hours.

CHANGING THE DATE FORMAT

Press and hold the [MENU) button to view the main menu.
Turn and press the [OW Volume) dial to select ‘System settings’ > ‘Time’.
Turn and press the [OW Volume) dial to choose ‘Set date format’.
Turn and press the [OW Volume) dial to choose between ‘DD-MM-YYYY’ and ‘1414-DD-YYYY’.

CHANGING YOUR PREFERRED LANGUAGE

You can select the language for menus and options.

Press and hold the (MENU) button to view the main menu.
Turn and press the [OK/ Volume) dial to choose ‘System settings’ > language’.
Turn and press the [OK/ Volume) dial to select a menu language.

BACKLIGHT

You can adjust the duration that the screen is illuminated for and the brightness of the screen when:

Timeout

To adjust the duration of the screen backlight before dimming:

Press and hold the [MENU] button to view the main menu
Turn and press the [OK/ Volume] dial to choose ‘System settings’ > ‘Backlight’.
Turn and press the [OK/ Volume] dial to choose ‘Timeout’.
Turn and press the [OK/ Volume] dial to choose a timeout setting. To specify that the backlight should always remain on, choose ‘On’.

On level

Press and hold the [MENU] button to view the main menu
Turn and press the [OK/ Volume] dial to choose ‘System settings’ > ‘Backlight’.
Turn and press the [OK/ Volume] dial to choose ‘On Level’.
Turn and press the [OK/ Volume] dial to choose between ‘High’, ‘Medium’ or ‘Low’.

Dim level

Press and hold the [MENU] button to view the main menu.
Turn and press the [OK/ Volume] dial to choose ‘System settings’ > ‘Backlight’.
Turn and press the [OK/ Volume] dial to choose ‘Dim Level’.
Turn and press the [OK/ Volume] dial to choose between ‘High’, ‘Medium’, ‘Low’.

EQUALISER

Several predefined EQ settings are available; also a user-defined setting (My EQ). To choose an EQ setting,

Menu > System settings > Equaliser.

You can then choose from a variety of predefined settings and My EQ. The last option ‘My EQ profile setup’ allows you to define your own settings for the ‘My EQ’ option, with custom bass and treble settings. Rotate the [OK/ VOLUME] to select and press dial to confirm.

CARRYING OUT A FACTORY RESET

Resetting removes all presets, stored stations, alarms and resets all other options to default settings.

Press and hold the [MENU] button to view the main menu…
Turn and press the [OK/VOLUME] dial to choose ‘System settings’ > ‘Factory Reset’.
Turn and press the [OK/VOLUME] dial to select ‘Yes’ to reset factory settings. Select ‘No’ if you do not want to reset to factory settings.

DAB SETTING

Note: You can only see the DAB settings when you have selected “DAB” as the radio source.

Full scan

You can use the “Full Scan” (auto tune) function to automatically scan for new digital radio stations and remove inactive ones. To carry out an auto tune, press the [SCAN/ENTER] button .The number of stations found will be displayed during the auto tune. When the auto tune has finished, the last station that you were listening to. If the last station you were listening to is no longer available, will tune into the first station in the alphabetical list.

Manual tuning

To manually check the signal strength of a known channel:

Press and hold the [MENU] button to view the main menu.
Turn and press the [OK/VOLUME] dial to choose ‘Manual tune’.
Turn and press the [OK/VOLUME] dial to choose the channel

Dynamic range control

Dynamic Range Control (DRC) is used to make quieter sounds in a digital radio broadcast easier to hear at low volume or in a noisy environment. Check with the broadcasters to find out if they use DRC. To change the DRC settings:

Press and hold the [MENU] button to view the main menu.
Turn and press the [OK/VOLUME] dial to choose ‘DRC’.
Turn and press the [OK/VOLUME] dial to choose between one of the following options:
- DRC high: Applies maximum compression to the DRC level.
- DRC low: Applies reduced compression to the DRC level.
- DRC off: Removes DRC compression.

Prune

To delete all radio stations that have no signal select ‘’Yes’’ , Or select ‘’No’’ to go back to the DAB+ menu

FM RADIO SETTING

Note: You can only see the FM radio settings when you have selected ‘FM’ as the radio source.

FM stereo option

You can choose between stereo or mono reception when listening to FM radio. Mono may improve clarity where stereo signals are weak.

To change between Stereo or Mono reception:

Press and hold the Menu button to view the main menu.
Turn and press the Select dial to choose ‘Audio Setting’.
Select between ‘Stereo Allowed’ or ‘Forced Mono’.

FM scan

You can choose whether automatically stops at the next available FM station or the next available FM station with a strong signal when scanning for an FM station. To change the FM scan setting:

Press and hold the [MENU] button to view the main menu.
Turn and press the [OK/VOLUME] dial to choose ‘Scan Setting’.
Select between ‘Strong Stations Only’ or ‘All Stations’.

TECHNICAL SPECIFICATION

Playback options	BT streaming, DAB+ tuner, FM radio
Output connections	3.5mm Jack
Output power	50W
Power supply	100-240VAC 50/60Hz (5V Adapter)
Dimensions (L x W x H)	280 x 110 x 110mm
Weight	1,05