EnjoySeating 91CYGTkHnLL Office Chair Instruction Manual
- June 14, 2024
- EnjoySeating
Table of Contents
EnjoySeating 91CYGTkHnLL Office Chair
Product Information
This product is a chair designed for comfortable seating. It comes with various parts that need to be assembled properly.
Product Usage Instructions
Step 1: Assembly of the Base and Base Legs
Turn the Base (F) upside down, then insert Base Legs (G) one by one to the
Base. Use the Wrench (M) to screw 5 Bolts M6x10(I) into the pre-drilled screw
holes to fix the Base and the Base Legs.
Step 2: Installation of Casters, Gas Li, and Hood
Press the Casters (H) into the holes at the end of each Base Leg. Insert
the Gas Li (E) and the Hood (N) into the center hole of the Base.
Step 3: Assembly of Backrest and Armrests
Align the backrest (A) to the armrest, and insert the backrest into the
armrest (C). Find the screw holes on the back of the backrest and screw the
bolts M6x20 (L) in. All bolts do not need to be tightened, they only need to
be fixed in half.
Step 4: Attachment of Seat Cushion and Armrests
Turn the Seat Cushion (B) upside down and align the hole position of the
Armrest (C) with the pre-drilled hole position under the Seat Cushion. Attach
the Armrest (C) to the Seat Cushion (B) with Four Bolts M6x35(K), using the
Wrench (M) to tighten them. Fully tighten the Bolt (L)*4 to fix the armrest
and backrest.
Step 5: Attachment of Seat Cushion to the Mechanism
Attach the Seat Cushion (B) to the Mechanism(D) using Four Bolts M6x16(J).
The mechanism tension knob should be in the front of the cushion.
Step 6: Attachment of Mechanism to Gas Li
Align the hole of the mechanism to the gas li and insert the upper part
into the gas li.
Step 7: Attachment of Headrest to Backrest
Attach the headrest (O) to the backrest using Two Bolts M6x20(L).
Instructions For Use:
Seat Height Adjustment:
Paddle-shaped lever on the right side. To raise: While taking your weight
off chair, lift lever up. To lower: While seated, lift lever up. At the proper
height, your feet should rest flat on the floor.
Operating the Rocking Function:
Rotate the knob under the seat cushion to adjust the shaking amplitude. To
let your chair tilt back, pull the control handle out. To stop your chair from
tilting, sit forward, then push the control handle in.
Headrest Adjustment:
Move the headrest up or down to adjust the height. Angle the headrest
upward/downward.
Greetings,
Hope you are having a lovely day! Thank you so much for trusting our company.
Your order means so much to us, we hope it meets all your expectations ! We
have put our heart and soul into this amazon business, so if you have any
problems or issues, please email us, so we help you.
Yours Sincerely
Enjoyseating
Congratulations, you are now the owner of a brand new home & office chair!To best enjoy the comfort of the chair, you have to put it together first! This assembly guide will take you through the assembly process. To make sure the assembly goes well, please follow the instructions, and especially the important safety information.It is possible to assemble the chair on your own, but it is recommended to have a second person to make it easier and safer.
Please check if there are any missing parts from the package before starting. If there is any issue, please don’t hesitate to drop us an email and we’ll help you out ASAP. If you run into any difficulty when assembling the chair, remember to check out the assembly video to see if you’ve missed anything. If you’re unable to resolve the problem, just send us an email and our support team will assist you.
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure
to follow this warning can result in serious injury to yourself or others.
Package List
Without further ado, we kindly suggest you to list all parts needed for the chair first.
Assembly Instruction
Step 1:
- Turn the Base (F) upside down,then insert Base Legs (G) one by one to Base.
- Use the Wrench (M) to screw 5 Bolts M6x10(I) into the pre-drilled screw holes to fix the Base and the Base Legs.
Step 2:
- Press the Casters (H) into the holes at the end of each Base Leg.
- Insert the Gas Lift (E) and the Hood (N) into the center hole of the Base.
Step 3:
- Align the backrest (A) to the armrest, and insert the backrest into the armrest (C).
- Find the screw holes on the back of the backrest and screw the bolts M6x20 (L) in.
- All bolts do not need to be tightened, they only need to be fixed in half.
NOTE:
The seat cushion and the mechanism is divided into front and back, and the
armrests are divided into left one and right one. Please observe carefully.
Step 4:
- Turn the Seat Cushion (B) upside down and align the hole position of the Arm-rest (C) with the pre-drilled hole position under the Seat Cushion.
- Attach the Armrest (C) to the Seat Cushion (B) with Four Bolts M6x35(K), using the Wrench (M) to tighten them.
- 100% tightened the Bolt (L)* 4 to fix the armrest and backrest.
Step 5:
- Attach the Seat Cushion (B) to the Mechanism(D), Use the Wrench (M) to screw Four Bolts M6x16(J) .
- Attention: The mechanism tension knob should be in the front of the cushion.
Step 6:
Align the hole of mechanism to the gas lift, and insert the upper part into
the gas lift.
Step 7:
Attach the headrest(O) to the backrest,Use the Wrench(M) to screw 2 Bolts
M6x20(L) .
CAUTION:
Make sure all bolts and screws are fully tightened before using chair.
Instructions For Use
-
Seat Height: Paddle-shaped lever on the right side
-
To raise:
While taking your weight off chair, lift lever up. -
To lower:
While seated, lift lever up.
At the proper height, your feet should rest flat on the floor.
-
-
Operating the rocking function
- Rotate the knob under the seat cushion to adjust the shaking amplitude.
- To let your chair tilt back, pull the control handle out.
- To stop your chair from tilting, sit forward, then push the control handle in.
-
Headrest: 2D
- Move the headrest up or down to adjust the height.
- Angle the headrest upward/downward.
-
Casters
Best suited for hardwood and tile floors. They glide silently and smoothly.
Safety And Maintenance
- Do not stand on the chair, Do Not use the chair as a stepladder.
- Use this product for seating one person at a time.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
- Chair weight limit not to exceed 300 lbs.
Safety Information
Limited Warranty
During warranty, if the following malfunction occur during normal use, please feel free to contact us by email, our customer service email: (enjoyseatingservice@gmail.com; anjiyike@163.com).
-
Warranty terms
Object part| Malfunction| Warranty time
---|---|---
Mechanical structure| Malfunction and damage of cushions, backrest and casters| Two years from the date of purchase
Structural parts| Deformation, damage, corrosion, etc of the main steel structure| Two years from the date of purchase -
Warranty items are applicable to all models, please feel free to contact us after the warranty expired’s repairing.
-
Out of Guarantee
The following conditions are not included in the warranty.- Malfunction or damage caused by accident, fire, flood or natural disaster.
- Malfunction or damage caused by misuse, abnormal use, improper repair or personal modification.
Write to our respected customers:
- In the process of chair development, we pay most attention to chair comfort, followed by appearance and function.Before mass production of chairs, we will invite a large number of people to experience the comfort of chairs, from workshop staff to office staff.
- In combination with the user experience, we constantly adjust the details of the chair, from the choice of fabric, the thickness and density of sponge, as well as the width, depth and angle of the chair, to achieve the most comfortable siting experience.
- We hope that our efforts will enable you to sit on our chair and be really comfortable and relaxed.
- Feel free contact with us if you have any questions.
Your sincerely
Enjoyseating
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>