ANZZI BA-LMDFVCB007AL LED Mirror Installation Guide
- June 6, 2024
- ANZZI
Table of Contents
Item: BA-
LMDFVCB007AL
ANZZI LED MIRROR
INSTALL & OPERATION MANUAL
V1.0
BA-LMDFVCB007AL LED Mirror
DON’T WAIT!
REGISTER NOW!
Register your product within 90 days to ensure your product is recognized as
an official purchase and is eligible for warranty coverage.
Mail in the completed registry card (Pg. 2) or register online at
www.swcorp.com/register.
PRODUCT REGISTRATION∗
IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULLY
COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED.
To ensure that your warranty is registered and confirmed please do one of the
following:
- Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information.
- Complete, cut-out and mail the registration card below.By returning this registration card we confirm the date of purchase for your new product. This confirmation will allow us to process any warranty claims.
Mail the card to: 5701 NW 35 Avenue, Miami, FL 33142
Product Registration Card
CUT ALONG DOTTED LINE.
Name……………………………………………..
Address ……………………………………..
City………………………………………..
State ………………………
Zip………………………………..
Phone …………………………
Email ……………………………..
Date of Purchase ………………………
Installer’s Name …………………………..
Phone …………………………………………..
I have read the Owner’s Manual carefully and understand and agree that any
installation, operation or maintenance of the product must be done strictly in
accordance with instructions and guidelines contained in the owner’s manual
and installation guide.
Signature_____
Date ____
Have questions? Call us at or visit us at 1-844-44-ANZZI
www.ANZZI.com
*BA-LMDFVCB007AL 32″28″** 
INSTALLATION INSTRUCTIONS
Apply to the below style of LED medicine cabinet
Please read carefully and save these instructions.
Don’t discard any of the packaging until you are sure that you have all of the
parts and the fittings.
Make sure power to the junction box is off before commencing installation.
IMPORTANT
- Unpack LED cabinet. DO NOT lay cabinet on tiled or concrete surface prior to installation.
- Cabinet must be on protected surface to prevent chipping of the corners.
- Care must be taken before drilling pilot holes to avoid any existing wiring or pipe work that may be concealed.
- Acertified electrician must perform all work. The mirror must be connected to a GFI.
INSTALLATION
Please refer the installation diagram on next two installations manual.
- Unpack the LED medicine mirror and prepare tools needed. (See Pic.1)
- Make sure the measurement on the carboard screw holes are matching up with aluminum base on the mirror back, then mark the screw holes according from the carboard with pencil.(See Pic.2)
- Drill holes, and put in the plastic expansion bolt, then fix the aluminum bar by screws. (See Pic.3&Pic.4);
- Connect hardwire to power line. Make sure the power off(Voltage:AC110-120V, 50/60Hz).(See Pic.5)
- Hang the cabinet on the wall; don’t remove your hands until its safety. (See Pic.6)
- According to your needs, put metal buckles into cabinet holes in suitable height, then install the glass shelves. (See Pic.7&Pic.8)
- Find the correct door panels by referring to drawings.Place the door panel on the side panel of the cabinet. Secure the hinges on the system holes of the side panels of the cabinet , then install a buffering hinge on each of the two cabinet panels.(See Pic.9&Pic.10)
- Connect the DC line of the cabinet door panel to the electrical box .(See Pic .9)
- Connect the lower end of wall with the cabinet body by using the corner brace.(Pic .11)
FUNCTION DESCRIPTION
Turn the light and anti-fog function by the dimmable sensor switch , see
details as below:
Button:
a) Touch the button for LED light and anti-fog control;
b) Long press button for dimming. It will change the LED brightness from
10%-100%.
MAINTENANCE
Wipe clean with a soft damp cloth. Apply glass cleaner to cloth and do not
apply directly to mirror.
Never use abrasive cleaners as these could damage the finish or exposed
LEDstrip
INSTALLATION DIAGRAM
