unu 2023 Electric Moped Scooter User Guide

: June 10, 2024
: unu

Table of Contents

Quick Start Guide
Display & battery
Essentials
- Your battery
Drive, park & off
Jump start your scooter
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

unu 2023 Electric Moped Scooter

Quick Start Guide

Unbox your scooter

It’s best to have a second person help unbox the scooter.

Remove the top lid of the box.
Remove the four side walls by sliding them upwards.
Lift the back wheel by the rear handle and move it off the platform.
Lift the front wheel off the package by the handlebar.
Unfold the kickstand to stabilize the scooter.

On/off, lock, seatbox

Lock/turn off button 2
Unlock/turn on button
Seat box button Mount your mirrors

Turn On: Press the Unlock/turn on button. Fold the kickstand up to enter drive mode. Turn Off: Press the Lock/turn off button.
Lock: Turn the handlebar all the way to the left and long press the lock/ turn off button (1) until you hear the locking sound on the scooter (approx. 5 sec.).

Mount your mirrors

Your scooter should be in park mode and its handlebar unlocked

Place both mirrors on a flat surface so that they form a V shape.
Pick the left mirror and turn the bottom nut all the way up until you feel resistance.
Screw the bolt clockwise into the left side of the handlebar. It is normal that the bolt doesn’t go all the way in. Do not use force!
Turn the mirror into a position, so that you can see what is behind you (this can be adjusted later)
Tighten the nut with a wrench (17mm) until the mirror is fixed in one place.
You can loosen the nut at the top of the mirror arm to adjust the mirror’s vertical orientation. Make sure to tighten the nut again.
For fine tuning, press gently on the mirror glass to change its orientation.
Repeat with the right mirror.

Display & battery

Charge your battery
Turn off the scooter, open the seat box via the key fob and unplug the battery.
Plug the battery to the charger by pressing the plug on the connector. The battery is fully charged when the led on the charger turns green. To use your battery, turn off your scooter and plug in the battery cable.
Display & battery

Essentials

Your battery

Main battery

→ Charge the main battery at room temperature. Do not charge it when the battery is still cold from outside.
→ Do not leave the battery in your scooter for several weeks at temperatures below 0°C.
→ Unplug the charger, when the battery is fully charged.

State of charge

The state of charge is measured differently on the battery and on the display. Use the battery according to the state of charge shown on the Scooter Display for a range estimation.

Drive, park & off

Drive & Park

To enter drive mode, fold the kickstand up.
To enter park mode, fold the kickstand down. Inspection Your first inspection is due when you reach 500km or after 12 months. It then needs another after 4.000 km. Check our website to find a partner garage.

When turned off, your scooter continues to run on its internal battery. After roughly 28 days without driving your scooter, the internal battery might be depleted and your scooter won’t start. If this is the case you need to jump start your scooter.
Reminder: The internal battery is being charged when the scooter is turned on (parked or driving).

Jump start your scooter

If your scooter is not turning on and the seat box is not opening, it is probable that your internal battery is low.
In this case you need to jump start your scooter using the provided jump start kit. Beware that without the main battery connected the display of your scooter won’t be on, be sure to try to open the seat box and insert the main before using the Jump Start Kit.

Charge power bank

Check if the power bank is charged by pressing the control button (1).
Charge the power bank using the provided cable (A) in port (5).
You can also use the power bank to charge other devices like your phone

Jump start your scooter

Plug the cable (B) into the jump start port (6).
Plug the other side into the scooter. The port is on the left side close to the rear wheel. To plug the jump start cable into the scooter you must place the white dot from the connector towards the scooter and try to find the correct position.
To support you at night, you can turn the flashlight on/off by long pressing the control button (1).
Turn your scooter on using the key fob.
Insert a main battery, unplug the power bank and let the internal battery charge

Reminder: Do not leave the jump start kit attached to the scooter.