ANZZI SD-AZ051-01 Semi-Frameless Hinged Shower Door User Manual

ANZZI SD-AZ051-01 Semi-Frameless Hinged Shower Door

INSTALLATION GUIDE

BEFORE YOU BEGIN

• Please check the product for damage and missing parts immediately upon delivery. Damage reported later will not be covered by our warranty. Please handle the product with care. Avoid any impact to the sides and edges of the glass .
• Consult your local building codes before installation.
• To reduce the risk of breakage, keep corner protectors on the glass while installing.
• If this unit is being installed in new construction, please install all required plumbing and drainage before installing the shower. Use a (if required by local code) for all plumbing installations.
• Before beginning installation, make sure all surfaces are level, solid and will support the total weight of the unit. Also, make sure the walls are at right angles. Irregular installation surface level, radius corners, or improper angle of side walls will result in serious problems for your installation. Please note that some adjustments and drilling might be necessary during the installation process.
• Please protect all primary surfaces of the product during installation. Never set your glass down directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always use wood or cardboard to protect the bottom edge and corners of the glass before and during installation.

WARNING

• This unit must be installed upon a finished threshold and against finished walls.
• Take care to avoid hidden pipes or electrical cables when drilling holes in walls.
• This product is heavy and may require two people to install it.
• When cutting or drilling metal components or handling glass, wear protective eye wear, gloves, and closed-toe shoes to reduce the risk of personal injury.
• Failure to follow instructions when installing this product may result in personal injury, property damage, or product failure and may void the warranty

ATTENTION

• Threshold must be level for proper installation.

• This model requires a minimum 1-3/4″ (45mm) of flat level threshold space for installation.

• This product is heavy and may require two people to install.

• Use cut-resistant, non-slip gloves to reduce the risk of personal injury and to hold the glass firmly.

Tools Required

• This product is heavy and may require two people to install .

PARTS

ASSEMBLY

Part Description Qty. Part Description Qty.

• [01] Wall Post A 1
• • [02] Wall Post B 1 [OBA] Anchor (L) 1
• [03A] Magnetic Seal A 1
  • [03B] Magnetic Seal B 1
• [04] Seal 1
• [05] Water Sealing Strip 1
• [06] Door Panel 1
• [07] Handle Set 1
• [08B] Anchor (R) 1
• [09] Anchors 8
• [10] Screws ST 4×35 8
• [11] Screws ST 4×8 4
• [12] Screw Caps 4

SD-AZ051-01 24*72″
SD-AZ051-02* 3072″
ATTENTION**

• To avoid personal injury or property damage, identify components and read all instructions before installing.
• This model requires a minimum 1-3/4″ (44mm) of flat level threshold space for installation.
• The instructions below are for Door Panel [06] option installed on the left.

INSTALLATION INSTRUCTIONS

Step 1

1. This shower door must be mounted to a wall stud. Minimum threshold space is required.
   IMPORTANT: Using a stud finder, ensure the wall intended to hold the door has a stud at the installation point. If there is no stud in the shown area, we recommend employing a qualified contractor to install one. (Fig 1)

2. This manual shows left side installation. For right side installation, transpose all instructions.

3. Using a level, position the Wall Post A [01] and Wall Post B [02] on the threshold. (Fig 1)

Step 2

1. Mark the drill hole locations on the wall using the predrilled holes in the Wall Post A [01] and Wall Post B [02] (Fig 2.1, Fig 2.6).
2. Drill a 1/4″ hole at each location and insert the Anchors [09] (Fig 2.2, Fig 2.3, Fig 2.7, Fig 2.8).
3. Apply silicone sealant along the back of the Wall Post A [01] and Wall Post B [02] (Fig 2.4, Fig 2.9).
4. Fasten the Wall Post A [01] and Wall Post B [02] to the wall with the Screw ST4X35 [10] (Fig 2.5, Fig 2.10).

ATTENTION
Wear safety glasses and cut-resistant, non-slip gloves when drilling or cutting to avoid risk of injury.

Step 3

1. Push the Magnetic Seal B [03B] into the groove of Wall Post B [02] (Fig 3.1).
2. Snap the Magnetic Seal A [03A] to the Door Panel [06] (Fig 3.2).
3. Slide the Door Panel [06] into the groove of Wall Post A [01]. Hold the Door Panel assembly in the closed position so that the Magnetic Seal A [03A] can attach to the Magnetic Seal B [03B] from top to bottom (Fig 3.3).

Step4

1. Make final adjustment (up to 1/2″) if needed. Hold the Door Panel assembly steady and drill the holes through the first layer of the Wall Post A [01] and into the Door Panel assembly using an 1/8″ drill bit (Fig 4.1 ).
2. Secure the Door Panel assembly to the Wall Post A [01] with 1he Screw ST4X8 [11] (Fig 4.2).
3. Cover the screw heads with the Screw Caps [12] (Fig 4.3).

Step5

1. Attach the Water Sealing Strip [OS] onto the Door Panel [06]. The flange of the Water Sealing Strip [05] should face the wall. (Fig 5.1)
2. Apply a good quality Silicone Sealant to the bottom of 1he Seal [04]. Connect 1he Seal [04] to the Anchor (L) [08A]. (Fig 5.2)
3. Connect the Anchor (R} [08B] to 1he Seal [04]. (Fig 5.3)
4. Install the seal assembly to the threshold as shown.
   Note: The anchor should align to the outermost surface of Door Panel [06]. The inclined curved surface of the seal should face the wall.

Step6

1. Disassemble gaskets by removing handle lever and handle knob (Fig 6.1 ).
2. Install handle and one gasket on the outer surface of Door Panel [06]. Connect the handle lever and one gasket to the handle from the other side of Door Panel [06] through the upper hole of Door Panel [06]. Hand tighten the handle lever to secure. (Fig 6.2)
3. Connect the handle knob and one gasket to the handle from the other side of Door Panel [06] through the lower hole of Door Panel [06]. Tighten the handle knob by allen key to secure. (Fig 6.2)

IMPORTANT: Ensure handle gaskets are placed on each side of glass.

Step 7
Apply a good quality Silicone Sealant at the outer corner formed by the wall, the seal and the shower door. (Fig 7)

• Allow 24 hours for the silicone to fully cure before using the shower.
  

Care & Maintenance

• BASES and BACK WALLS: To ensure long-lasting life for your acrylic bases and back walls (if installed), wipe them off after each use with a soft cloth. To clean the acrylic surface, use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes, or scrapers, as they can scratch or dull the surface.
• GLASS: To ensure long-lasting life for your glass shower products, after each use rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots (hard water can etch the surface of the glass over time if left to dry). To avoid damaging the surface, never use abrasive cleaners or cleaning products that contain scouring agents. Likewise, never use bristle brushes or abrasive sponges that can scratch the surface.
• HARDWARE: To ensure a long-lasting finish, wipe off the metal parts after using with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach, or acid. If accidentally used, rinse the surface as soon as possible to prevent damage to the finish (peeling or corrosion). After cleaning the polished finishes, rinse thoroughly and wipe dry with a soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish to stainless steel hardware, work with (not across) the grain. Never use an abrasive sponge or cloth, steel wool, or wire brush, which may permanently scratch the surfaces.

NOTE: Regularly inspect the glass and all hardware for misalignment, proper attachment, and damage. Contact ANZZI with any questions or concerns.

PRODUCT REGISTRATION

IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULIY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED.

To ensure that your warranty is registered and confirmed please do one of the following

1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information.
2. Complete, cut out and mail the registration card below. By returning this registration card we confirm the date of purchase for your new product. This confirmation will allow us to process any warranty claims.

Mail the card to : 5701 NW 35 Avenue, Miami, FL 33142

Product Registration Card

• Name ……………………….. Address ………………………………………………………. .
• City ……………………… State………. …. Zip …………………. .
• Phone …………………………… Email ………………………………….. .
• Date of Purchase …………………….. .
• Installer’s Name ……………………………………….. Phone ………… ……………… …. .

I have read the Owner’s Manual carefully and understand and agree that any installation, operation or maintenance of the product must be done strictly in accordance with instructions and guidelines contained in the owner’s manual and installation guide.
Signature. ___ .Date———–

Need help? For technical support call 305-614-4070 or visit us at www.ANZZl.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>