Litepanels 9402001 LED Stage and Studio Luminaire Instructions
- June 6, 2024
- Litepanels
Table of Contents
Litepanels 9402001 LED Stage and Studio Luminaire
SAFETY INFORMATION
To clean the GEMINI 2X1 HARD, wipe with a clean, dry, non-abrasive cloth only.
- Weight (including Yoke, not including accessories): 11.5 kg [25.3 lb]
- Dimensions (including Yoke, not including accessories): W = 74.8 cm [29.4 in], H = 52.9 cm [20.8 in], D = 17.6 cm [6.9 in]
Do not restrict air flow around the GEMINI 2X1 HARD. Keep the fixture’s air intakes and air exhaust space clear of obstruction. Plug the GEMINI 2X1 HARD into a mains electrical outlet using only a provided AC powerCON power cable or one specified by Litepanels®. Protect the cable from pinching, twisting, or crushing. Use a mains electrical outlet that is grounded and rated for 100-240VAC, 50/60Hz only. Do not use, mount, transport, or store the GEMINI 2X1 HARD near radiators, space heaters, ovens, stoves, heat registers, open flame, or any heat source, or in an environment with an ambient temperature greater than 65°C [149° F]. The GEMINI 2X1 HARD is suitable for operation only in an environment as follows: ambient air temperature between -20°C and 45°C [between -4°F and 113°F]; less than 85% relative humidity (RH), no condensation. Use in a dry environment; do not place on a wet surface or submerge the GEMINI 2X1 HARD in liquid. WARNING: Tampering with or disassembling the GEMINI 2X1 HARD may result in electric shock and will void the manufacturer’s warranty.
WARNING:
To reduce the risk of electric shock or fire, do not expose the GEMINI 2X1
HARD to rain, moisture, or liquids. Immediately consult with qualified
Litepanels® service personnel if any of the following have occurred: The
fixture has been dropped or impacted; the power cable has been damaged; the
fixture has been exposed to rain, moisture, or liquid; or the fixture does not
operate normally.
INCLUDED
- GEMINI 2X1 HARD Light Fixture
- GEMINI 2X1 HARD Yoke
- Ultra-Light Diffuser
- Domed Diffuser
- Hex L-Key, 6mm (not pictured)
- DIFFUSER LATCH(2X)
- DIFFUSER FLAP
- YOKE
- TILT LOCK SCREW
- AIR INTAKE
- ANTENNA
- UNIVERSAL COMMS PORT
- USB PORT
- TILT LOCK KNOB
- 1/4-20 FEMALE THREAD (2X)
- AIR EXHAUST
- DOVETAIL CHANNEL (2X)
- MAINS AC POWER INPUT
- MAINS AC POWER THROUGH
- 3-PIN XLR DC POWER INPUT JACK
- ACTIVE COMMS INDICATOR LIGHT
- 5-PIN XLR DMX / LEAD/FOLLOW INPUT
- 5-PIN XLR DMX / LEAD/FOLLOW OUTPUT
- RJ45 DMX / LEAD/FOLLOW INPUT
- RJ45 DMX / LEAD/FOLLOW OUTPUT
- DISPLAY
- CANCEL BUTTON
- PRESET BUTTONS (6X)
- PRESET TOGGLE BUTTON
- GREEN OFFSET / HUE / MENU KNOB
- CCT / SATURATION KNOB
- DIMMER / INTENSITY KNOB
- POWER / STATUS INDICATOR LIGHT
- ON / OFF SWITCH
- STANDARD JUNIOR PIN
- ACCESSORY LATCH
FCC Rules.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment, This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
- This Class B digital apparatus complies with Canadian ICES-003.
- The equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment,
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- The equipment should be installed and operated with minimum distance 20cm between the radiator and your body.