ZUOWEI ZW279PRO Intelligent Incontinence Cleaning Robot User Manual
- June 6, 2024
- ZUOWEI
Table of Contents
ZUOWEI ZW279PRO Intelligent Incontinence Cleaning Robot
Product Introduction
Product list
Parts Name
Instruction of remote control
|
Stop button:Stop the current processing action;
---|---
|
Indicator showing the low, mid.high of the temps.
| Wind temperature adjustment button : Touch the up arrow or down arrow of the button to adjust the wind temperature high or low, a total of high, medium and low three adjustable;
| Water pressure adjustment button: Touch the up arrow or down arrow of the button to adjust the strength or weakness of the water
pressure, with a total of three adjustable high, medium and low levels;
| Water temperature adjustment button: Touch the up or down arrow of the
button to adjust the high or low water temperature, with a total of three
adjustable high, medium and low levels;
| Poop button : In manual mode, press this button to enter the poop handling
procedure;
|
Pee button: In manual mode, press this button to enter the pee procedure;
|
Cleaning button: In manual mode, press this button to rinse the inner surface of the working head;
| Wash button: In manual mode, press this button to clean the private parts of
the person with warm water ;
|
Dry button: In manual mode, press this button to dry;
|
Manual button: long press this button, it will switch to manual mode;
|
Auto button: Press and hold the button, it will switch to manual mode;
Water filter bucket, sewage bucket and deodorizing compenents
Display screen
Modes Selection
- Manual mode: After selecting manual mode, poop, pee, clean, wash.and dry will enter the selectable state.
- Automat,c mode: When automatic mode is selected, poop, pee, clean, wash, and dry will all be unselectable, and the system will automatically perform poop and pee processing.
- Clean air: When clean air is selected, the system performs air purification.
Manual mode
- Setting page
- Status display
- Adjustment instructions
- Inquiry Page
Installation method
Sewage bucket installation method
- Turn the sewage bucket lid clockwise to the logo position
- Put th sewage bucket in the host machine.
- Put the sewage bucket into the host , and push in the snap click to lock it.
- To remove the bucket, press the unlock button to pull out the movable pin.
Water filter bucket installation method
- Turn the bucket lid clockwise to tighten
- Place the water filter bucket into the Host with the bucket lid facing down
Deodorization component installation
- Reach your fingers into the groove of the front cover and lift the cover outward.
- Holding the deodorant assembly box in your hand, push the deodorant assembly into the mounting opening along the guide slot and push the deodorant assembly to the bottom with a little pressure.
Hose assembly with Host installation
- Grasp the hose sewage tube connector, first Host wire from the hose wire hole through, then the Host connection part aligned and pressed into, and finally the hose assembly signal wire and Host wire for line connection.
- Turn the hose connector clockwise to lock in the Host connection section
Usage
Applicable people
- Without catheter, without urine volume monitoring;
- Those with no bed sores, severe dermatitis or impaired skin;
- Body weights overorequalsl to 35 kg;
- No serious deformation of thighs;
- The diameter of the dry and hard stool must be less than 33 mm;
- No severe hemorrhoids;
- No mental manic behavior (e.g. tearing the quilt, grabbing the poop by hand, pulling the diaper);
- Users should lie flat and keep the side lying less than 30°when urination and defecation while using.
Start-up preparation
- Make sure the connection between the working head and the connecting hose is intact;
- Make sure the connection between the Host and the connecting hose is intact;
- Make sure the water filter bucket is filled, and the Host is loaded;
- Make sure the sewage bucket has been emptied and loaded into the Host;
- Make sure the deodorant component box is properly loaded into the Host;
- Make sure the hip pads are properly put on;
- Make sure the leakage protection plug is plugged into the power supply, and the working indicator light is lit.
Machine cleaning
The machine can not be directly sprayed and washed before cleaning, you can wipe with a cloth.
Machine handling
Before moving the machine, you need to pour out the water in the water purification bucket and clean the sewage bucket and then open the drain valve at the bottom of the water purification bucket to empty the water inside the main machine.
Usage schedule
It suggest that the initial use time in each day should be gradual increase , to keep the user gradually adapt to the use this machine.
- Day 1: 4H (Daytime)
- Day 2: 8H (Daytime)
- Day 3: 1 OH (Daytime)
- Day 4: 12H (Daytime)
- Day 5: 12H (Evening)
After that, it is recommended that each continuous use time should not exceed 12 hours.
Attention
-
Before using the intelligent incontinence cleaning robot, check whether the Velcro on the base of the smart bedpan is aligned with the Velcro on the pants, and whether the
smart bedpan falls exactly in the U-shaped slot of the pants (for details, please refer to the ” Instruction Manual of the Smart Bedpan ” ). -
Please check whether the user’s skin is red or damaged after each time use. If any above condition, it should stop use this robot and ask for the treatments from professional caregivers. And suggest to use the robot agin after full recovery.
Precautions during and after use
Attention during use
- After the use of the object position change (including left and right turn, sit up again after lying down, etc.), you need to confirm whether the work head is loose, misalignment (focus on confirming the inner thighs and soft rubber between) ;
- Users should lie flat and keep the side lying less than 30°when urination and defecation while using.
- Red light at the end of the machine, report equipment failure, immediately stop using the machine, and feedback to the manufacturer.
Precautions after use
- It is recommended to perform one time manual cleaning process before the smart bedpan is removed;
- First turn off the machine and then take off the smart bedpan and bag pants;
- After the smart bedpan is removed, it is necessary to clean the sewage bucket in time.
- The smart bedpan and pipe can’t forward down when taken off from host.the pipe should lift up higher than caregivers’ height, making the remaining water and sewage flow back to the host’s sewage bucket, then remove the pipe
Cleaning
Sewage bucket cleaning
Open the top lid of the host, hold the movable latch by hand and carry it to
the sink. Withdraw the connector and lift the sewage bucket out by hand by the
handle.
Turn the sewage bucket knob counter clockwise, hold the handle with one hand,
hook the bottom of the bucket with the other hand, and slowly pour the sewage
into the sink. 
You can open the buckle with water or water to add toilet cleaner will sewage bucket clean will sewage bucket outside surface of the water with a clean cloth or cotton, wipe clean, and then reassemble (see Sewage bucket installation method)
Automatic mode
Setting of automatic mode
INCONTINENCE CLEANING ROBOT starts up in manual mode by default. It will
switch to automatic mode 3 minutes later. Choose the” Device Control” in the
menu on touch screen.
- Click” Auto Mode” to enter the automatic working mode, in this mode other buttons can’t be selected , and the “Auto ” key on remote control will be light.
- Press the “Auto” button on the remote control, the device control interface on the current display will switch to “Auto Mode” simultaneously. The “Poop”, “Pee”, “Wash” and “Dry” icons are gray and the buttons are not clickable. state. The “Auto” button of the remote control is illuminated.
2How the automatic mode works
When the INCONTINENCE CLEANING ROBOT is working in auto mode, the robot will automatically start the preset program to collect excrement, clean and dry the defecation area after the user has defecated. If you need to stop the process during operation, to stop the current operation, click the “Stop” button on the display or tap the “Stop” button on the remote control.
Manual mode
Setting of manual mode: The system defaults to manual mode after the care robot is turned on, and automatically switches to automatic mode after 3 minutes. Automatic mode switch to manual mode This can be done in the following two ways
- Press the “Manual Mode” button on the device control interface to switch the system to manual mode. The icons of “Poop”, “Pee”, “Wash” and “Dry” on the display screen are activated and the button are restored to clickable state. At the same time, the “Manual” button on the remote control is illuminated.
- Press the “Manual” button of the remote control, the device control interface on the current display will switch to “Manual Mode” simultaneously. The “Poop”, “Urine”, “Wash” and “Dry” icons are activated and the buttons return to the clickable state. The buttons return to the clickable state. At the same time, the “Manual” button on the remote control is illuminated.
How the manual mode works: When the INCONTINENCE CLEANING SYSTEM is in manual mode, the Host will start the preset program to collect excrement, clean and dry the defecation area according to the manual operation information provided by Remote Control and the display. During operation, to stop the current work, tap the “Stop” button on the display or press the “Stop” button on the remote control.
Parameter setting and inquiry
- Parameter Setting: Click the “System Setting” button on the main screen of the display to enter the system setting interface.
- Water temperature setting: In the system setting interface, press the water temperature adjustment 3 settings, set the water temperature; touch the remote control water temperature adjustment key “A” “V” to set the water to set the water temperature.
- Wind temperature setting: In the system setting interface, press the air temperature adjustment 3 settings, set the air temperature; press the remote control air temperature adjustment key “/\” “V” to set the air temperature to set the water temperature.
- Water pressure setting: In the system setting interface, press the water pressure adjustment 3 settings, set the water pressure; press the remote control water pressure adjustment key “/\” “V” to set the water to set the water pressure.
- Record Inquiry: Press the “record inquiry” button on the main interface of the display to enter the record list interface, you can inquire about poop, pee, turn over, fault information. You can check the information of stool, urine, turn over and trouble.
Safety Warning
- It is strictly forbidden to add hot water over 40 degrees into the water purification bucket.
- When cleaning the machine, the power must be cut off first. Do not use organic solvents or corrosive detergents.
- Please read this manual in detail before use and operate the machine in strict accordance with the operating methods and precautions in this manual. In case of redness and blistering of the skin caused by the user’s physique or improper wearing, please stop using the machine immediately and wait for the skin to return to normal before using it again.
- Do not put cigarette butts or other flammable materials on the surface or inside the Host to prevent damage to the product or fire.
- Water must be added to the water purification bucket, when the residual water in the water purification bucket, heating water tank for more than 3 days without use, you need to clean up the residual water and then add water.
- Do not pour water or other liquids into the Host to prevent damage to the product or the risk of electric shock.
- Do not disassemble the care robot by non-professional personnel to avoid damage to personnel and equipment.
- Do not hit or knock the product to prevent damage to the machine.
- Do not pull the Remote Control connection cable to prevent it from breaking.
- Be sure to use the care robot in an environment with a temperature of 5°C-40° C and humidity of 25%-85%.
- When removing the working head, be sure to tap up the working head above the Host first to prevent dirt left in the hose assembly from flowing out.
- Be sure to place the working head higher than the Host when the machine is in operation to prevent backflow of water.
- Do not use heavy objects to press the hose assembly and do not over-bend the hose assembly.
- Make sure to use the correct voltage to prevent damage to the machine.
- If the power cord is damaged, to avoid danger, it must be replaced by a professional from the manufacturer, its maintenance department or a similar department.
- For physical, perception, ability deficiencies or lack of experience and common sense (including children) in the use of the product should be operated under the equipment service personnel, this equipment should not be used as children’s play apparatus.
- This equipment must be installed and used in power supply systems with grounding conditions.
Troubleshooting
| Failure phenomenon | Failure Cause | Exclusion method |
|---|
After plugging in the power/ press the on/o f button machine does not respond
| 1.The socket is not powered on|
Check if the socket is charged
2.Leakafle protection plug reset bu on is not pressea|
Press the rese t button
3. Leakage protect ion plug damaged| Contact af ter -sale s ser vice to
replace the leakage protect ion plug
4.Fuse is blown| Contact after-sales serv ice to replace the fuse
Water rurification bucke leaking
| 1.Bucket lid not tightened| Screw the bucket cover tightly
2.Valve seal damage| Reinstall the seal
3.Rotary cover seal damaged| Reinstall the seal
4.Buckel shell is broken| Get an after-sales service to replace the sewage
bucket
Sewage bucket leaking|
Sewage bucket shell broken
| Contact the after-sa les service to replace the sewage bucket
Machine stopped working| Machine malfunct ion| Troubleshoot according to
the prompt on the LCD and the voice alarm message
Leakage at the connection hose
| Machineconnector not tightened
or screws not tightened
| Tighten connecto rs and screws
0 -ring not installed or misplaced| Put the 0 -r ing into the groove correctly
The machine is running and the excrement is not collected properly
| 1.Clogged pipe| Clean the pipe
2.Poor pipe sealing| Find after-sales troubleshooting
3. Clogged deodorization filter
|
Replace deodorization filter
The working head does not spray water
| Clogged heating water tank strainer filter| Clean the filter with water
Clogged water pipe| Contact af ter-sales service
Water does not heat
| 1.Heater burned out| Con tact after-sales service
2.Damaged control board
|
Contact after-sales service
Leakage at the workin_g head and hose joint| The connection between the work ing head and the hose is not tight|
Correctly docked hose and work head , latch locked
Sealing ring at the hose joint is aging| Replace the seal
Water leakage in the machine
| 1.Damage to the water pipe inside the machine| Find after-sales
troubleshooting
2.Loose water pipe in the machine| Find after-sales troubleshooting
Exhaustias odor is s rong
| 1.Air purification device damage| Replace
2. Activated carbon filter failure| Replace
Side leakage when working head and body fit| The fit is not tight|
Check if there is a seam on the inner thigh
Loose pants| Check whether the package pants are loose
Anal flushing is not clean
| The work inR head is not centered on the priva e part of the body| Work
head centered on the body’s private parts
The volume of fcoop is small and does not fall in o the stool cavi ty| Need to
manually perform 1 stool
process before removing the work ing head
Specifications
Product Name| ****
ranual of intelligent care robot
| Rated frequency| 50-60HZ
---|---|---|---
Product Model| ZW279Pro| Rated current| 9A
Rated Voltage| 220V-| Useplace| Indoor
Maximum power| 2200W| |
Maintenance
- Take out the heating water tank partition every time (about one month), wipe the heating water tank surface and heating water tank partition with a clean cloth to remove water moss and other attached dirt.
- When the machine is not in use for a long time, please unplug the leakage protection plug, empty the water purification bucket, dirt bucket, and drain the water in the heating water tank at the same time.
- Every six months time need to replace the deodorizing component box to achieve the best air purification effect.
- Hose assembly, working head is recommended to be replaced once every 6 months.
Note: Please cut off the power of Host during the above maintenance.
Product recycling
When this product reaches the end of its life, please send it to a suitable place to protect the environment.
Warranty service
Thank you for purchasing our products, where it is under normal use, due to the quality of the product itself caused by the failure, within the warranty period, our company is responsible for free maintenance.
Warranty Description
- INCONTINENCE CLEANING SYSTEM Host free of charge for one year, the second year free of repair service fees only charged for replacement parts: the main accessories (working head and connecting hose assembly) free warranty period of six months. The start date of the warranty period is based on the product invoice date.
- Please keep the purchase invoice and warranty card as warranty proof, once the invoice is altered, the warranty will be invalid.
- For customers whose warranty has expired, please contact our customer service department, and our customer service center will serve you warmly.
Disclaimer
- No purchase invoice and warranty card.
- Damage to the machine caused by wrong use of voltage.
- Damage caused by self disassembly or repair.
- Damage caused by force majeure (such as earthquake, fire, war, etc.).
- Customers please read this manual in detail, we are not responsible for machine failure, skin redness, b I isteri ng, bed sores, in fection, etc caused by w rong use
Return and Exchange Policy
- Product performance failure within 7 days from the date of sale, the consumer can choose to return, exchange or repair.
- Product performance failure within 15 days from the date of sale, the consumer can choose to exchange or repair.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
Caution
- Max operation temperature: 40 degree C. Min operation temperature: -10 degree C.
- This product can be used in UK. This device can be used in UK.
- Products can be sold in UK Declaration of conformity Trimble Transportation declares that Micro system with Mobile Digital Video Recorder is in compliance with the essential requirements and other relevant provisions of Directive SI 2017/1206.
Applicant: Shenzhen Zuowei Technology Co., Ltd.
Address: Floor 2nd, Building 7, YiFenghua lnvation Industrial Park,
Dalang Steet, Longhua District, Shenzhen, Guangdong, China
Manufacturer: Shenzhen Zuowei Technology Co., Ltd.
Address: Floor 2nd, Building 7, YiFenghua lnvation Industrial Park,
Dalang Steet, Longhua District, Shenzhen, Guangdong, China
Frequency: 2402-2480MHz
Max power: -6.99dBm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>