Jiuli D010 GPS Pet Electric Fence User Manual

DO10
GPS Pet Electrorfic Fence
Equipment User Manual

Instructions

Preface Description: The GPS electronic fence has four modes of positioning functions (GPS+BeiDou+Galileo+Glonass), which can support up to three modes of positioning simultaneously. It adopts the advanced technology of wireless transmitting and receiving modules from Europe. By using a software algorithm, the device prevents any error caused by unsteady satellite signals. The largest covering distance is up to 1000 meters depending on the clients’ needs. When in operation, its alarm system will go off when your pet goes beyond the set control area (the alarm modes: sound/vibration / electric shock). When the pet returns to the safety area, the device will stop ringing. The product will automatically search for the strongest signal source to guarantee its accuracy.

Functions of the screen (icon insertion):

1. Two horns: V’ and “1”, representing no buzzer sound” and “buzzer sound” respectively.
2. Four vibration modes: “0”, “1”, “2”, and “3”, with “0” for no vibration, “1”for minor vibration,”2″ for moderate vibration and”3″ for strong vibration.
3. Three shock modes: “0”. “1”, “2” and “3” ,with “0° for none shock, “1”for mild shock, “2” for medium shock and”3″ for higl-voltage shocks.
4. Battery icon: The battery icon shows the present electricity level when it is being used or recharged.
5. Lock icon: After being effectively positioned, the lock at the bottom right of the screen will switch on automatically and the system is in operation.
6. Signal icon: When it detects a strong satellite signal, the signal icon will be on at the lower right corner, indicating that the device operates well. If the signal is weak in the area, the icon will not be on.
7. The “00” icon: The continuous flickering “00” indicates that the device is searching for satellites’ signals: long-time flickering suggests that the device has picked up the satellite signals and is prepared to a position.
8. The” – -” Icon. When this icon flickers, it means the device is set off and the screen can be shut down to enter the power-saving mode.
9. The icon “– . When it is flickering, it indicates the device will enter a deep-sleep mode in five minutes if not used. The GPS will be suspended, thus saving power.
10. The icon “: :”: When this icon flickers, it means that under the condition of full screen, you can repress the power button to start a new round of positioning.
11. The icon “ER”: Represents an error. If the device is used in a non-open area, where the GPS signal is weak and the number of satellites can not meet the needs of the device. the ” ER” sign will go on after 3 minutes of fruitless search. And the device will continue to search for satellites repeatedly.
12. The icon “NUM”: The two-digit NUMon on the screen represents the number of satellites currently detected.

B. the keys (illustration)

C. Usage:

1. Power key P: The power key has two modes: long press and shod press. Long Press: Press the power button for 3 seconds to switch on/off the device. Short Press: If the device is in a full-screen working state, you can press any key to reposition it without a restart.
2. Mode key M: The mode key is having the long press and the short press function. The default distance is “03”, meaning 30 meters. Press the “M” key for 3 seconds to enter the distance setting mode and the sign “03” will flicker. The users can use the up and down keys to adjust the distance. After 5 seconds, the system will automatically remember the set distance and return. The maximum distance the equipment can set is up to 1000 meters in radius, with the sign “AO” on. Shod press the M key can be used to set the alarm mode beyond the control area. There are three alarm modes: buzzer, vibration, and shock. The strength of vibration or shock can be freely selected by using the up and down keys. In 5 seconds, the system will automatically remember the selection and return.
3. Battery Status: The battery power can support the device working continuously for 15 hours, and you can press any key to check the battery level on standby. If the device isn’t in use for more than 5 minutes, the device will go into a deep dormancy, and the standby time can extend up to 50 hours maximally. When the frame of the battery flickers all the time, the device needs charging in time. The charging time is 3 hours. When it is charged in the boot state, the device will automatically shut down.
4. Metal Bars: The equipment is equipped with two metal rods of different lengths.
5. Every time the device restarts will default to the new location as the starting point. When shut down, the system will automatically save the set distance and alarm mode.

D.Fittings pictures:

1. One electronic fence training device.
2. One coil of the band.
3. One 5V DC charger
4. One charging cable
5. One package of contact points
6. One test bulb points
7. One manual

E.Statements

1. The equipment is a wireless fence training device with a signal sending and receiving function. You don’t need to enclose the pet’s activity control scope with anything such as flags or drawn lines on the grounds.
2. The largest radius can be preset up to 1000 meters.
3. The device has three alarm modes (buzzer, vibration, and electric shock). When pets are out of the preset scope the system will automatically go off.
4. There are three alarm modes with different intensities for different types of pets.
5. This equipment is slightly waterproof but can not be used in water.
6. The screen can display the preset distance, the three-alarm modes, the number of detected satellites, and the signal levels.
7. The system defaults to a buzzer alarm. Either the vibration or electric shock can be set as the mode. And when the pet goes outside of the set range the vibration or electric shock will keep ringing non-stop for 16 seconds followed by a 30-second pause. Then it will repeat this 3 times automatically. After three times of ringing, if the pet has still not returned to the safety area, the system will not ring again.
8. The strength of the GPS signal depends on environmental factors, such as dense woods, high-rise buildings, weather conditions, etc.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>