ETNA T110VRVSA Gas Hob Instruction Manual

October 27, 2023
ETNA

ETNA T110VRVSA Gas Hob

OPERATION

Description

  1. Standard burner
  2. Rapid burner or wok burner (depending on model)
  3. Simmer burner
  4. Pan support
  5. Drip tray
  6. Control knob

Read the separate safety instructions before using the device!

Igniting and setting

  1. 0 setting
  2. zone indication
  3. Low setting
  4. High setting

Each burner can be adjusted continuously between high and low heat.

Burners with electric ignition:

  • Press the control knob and turn it anticlockwise. The burner ignites.
  • Keep the control knob fully pressed for at least 3 seconds between high and low settings. The thermocouple safeguard is activated.

Burners without electric ignition:

  •  Press the control knob and turn it anticlockwise. Light the burner with a match.
  • Keep the control knob fully pressed for at least 3 seconds between high and low settings. The thermocouple safeguard is activated.
Use

Pans

  • Ensure that the flames always remain underneath the pan. If flames play around the pan, a great deal of energy is wasted. The handles can also become too hot.
  •  Do not use pans with a base diameter smaller than 12 cm. Smaller pans are not stable.

The recommended pan base diameters are:

  • rapid burner at least 24 cm.
  • standard burner at least 20 cm.
  •  simmer burner at least 12 cm.
  •  wok burner at least 24 – 26 cm.

Pan support

  • Put the pan supports down vertically without sliding them over the drip tray.

Burners

  • Put the parts of the burner in the correct order so they fit togetherproperly
  1. Burner cover
  2. Burner distributor
  3. Thermocouple
  4. Spark plug (some models)

MAINTENANCE

Maintenance

Regular maintenance immediately after use prevents spilt food from setting too long and creating stubborn stains that are difficult to remove. Use a mild cleaning agent. First clean the control knobs, burners and pan supports, and lastly the drip tray. This avoids making the drip tray dirty again during the cleaning process.

  Note! Do not clean burner parts in the dishwasher. The detergent  may harm the parts!

Stubborn stains on enamel (pan supports, burner covers, drip trays)
The best way to remove stubborn stains is with a liquid cleaning agent or a plastic scourer. Never use abrasive powder, abrasive pads, sharp objects or caustic cleaning agents.

Stubborn stains on stainless steel (drip trays)
The best way to remove stubborn stains from stainless steel is with a special stainless steel cleaning agent. Always wipe in the direction of the structure of the steel to avoid glossy patches (damage caused this way is not covered by the warranty!). The surface of stainless steel can fade slightly after a while.

Refer to the website www.etnaservice.nl for extra maintenance and cleaning instructions!

MALFUNCTIONS

Malfunction list

If you are in doubt that your gas hob is not working properly, this does not automatically mean there is a defect. Try to address the problem yourself first by checking the points mentioned below or visit the ‘ www. etnaservice.nl’ website for more information.

SYMPTOM POSSIBLE CAUSE SOLUTION
You can smell gas near the appliance. The connection to the appliance is
leaking. Turn off the main gas valve. Contact your technician.

A burner does not ignite.

| Plug not in socket. Faulty fuse/fuse in meter cupboard is switched off. Spark plug (4) dirty/damp. Burner parts not installed correctly. Burner parts dirty/damp. Main gas valve closed. Gas mains failure. Gas cylinder or tank is empty. Wrong type of gas used.| Put the plug into the socket. Fit a new fuse or switch the fuse back on. Clean/dry the spark plug. Put the parts of the burner in the correct order so they fit together properly. Clean/dry the burner parts. Make sure that the outflow holes are open. Open the main gas valve. Contact your gas supplier. Connect a new gas cylinder or have the gas tank filled. Check whether the gas used is suitable for the appliance. If it is not correct, contact your technician.
The burner is not burning evenly.| Burner parts are not installed correctly. Burner parts dirty/damp. Wrong type of gas used.| Put the parts of the burner in the correct order so they fit together properly. Clean/dry the burner parts. Make sure that the outflow holes are open. Check whether the gas used is suitable for the appliance. If it is not correct, contact your technician.
Burner extinguishes out after igniting.| You did not press the control knob long and/or deep enough (at least 3 seconds). Thermocouple (3) is dirty.| Keep the control knob fully pressed for at least 3 seconds between high and low settings. This can be longer the first time, because of the supply of gas. Clean/dry the thermocouple.

ENVIRONMENTAL ASPECTS

Disposal of the appliance and packaging

Sustainable materials were used in the manufacture of this appliance.
The appliance packaging is recyclable. The following may have been used:

  • cardboard
  • paper;
  • polyethylene film (PE);
  • CFC-free polystyrene (PS rigid foam);
  • polypropylene tape (PP).

The materials should be disposed of in a responsible manner and in accordance with government regulations.

The requirement for separate collection of household electrical appliances is highlighted by the symbol of a crossed-out dustbin which is attached to the product.
This means that at the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance such as this hob separately avoids possible negative consequences for the environment and health and enables the constituent materials to be recovered to obtain significant savings in energy and resources.

Declaration of conformity

We hereby declare that our products satisfy the applicable European directives, orders and regulations, as well as the requirements stated in the referenced standards.

The appliance identification card is located on the bottom of the appliance.

Stick the appliance identification card here.

When contacting the service department, have the complete type number to hand.

You will find the addresses and phone numbers of the service organisation on the guarantee card.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals