ETNA RA345, RA370 Cooker Hood Instruction Manual
- June 4, 2024
- ETNA
Table of Contents
COOKER HOOD
RA345–
RA370—
INSTRUCTIONS FOR USE
YOUR COOKER HOOD
Introduction
Reading through these instructions for use will help you quickly find
information about all the options you are offered by this appliance. It
contains information for your safety and about the maintenance of the
appliance.
Read the separate safety instructions before using the appliance!
Keep the instructions for use and the installation instructions. They will be
of value to any later user of this appliance.
You can find the most recent version of the instructions for use on our
website.
Description
- Extraction speeds LED indication
- Grease filter
- Lighting
- Lighting on/off key
- (+) increase extraction power key
- (-) decrease extraction power key
- Extraction on/off key
USE
Operation
Remote control
Switching the fan on and off
-
Touch the extraction on/off key.
• The cooker hood switches on at speed 1.
• The indicator on the cooker hood shows the selected speed:
▷ green = speed 1;
▷ orange = speed 2;
▷ red = speed 3;
▷ red, flashing = speed 4 (maximum of 7 minutes, after which the speed switches back to speed 3). -
If so required, select a higher speed using the ‘+’ key.
-
Select a lower speed using the ‘-’ key.
Switching the lighting on and off
- Touch the lighting on/off key.
▷ The light turns on.
▷ Touch the on/off key again to switch the lighting off.
Linking the remote control to the cooker hood
-
Disconnect the cooker hood from the power supply by setting the group fuse in the meter cupboard to ‘0’ or removing the fuse from the fuse holder. If present, the cooker hood can also be disconnected from the power supply with the On / Off switch located at the top of the cooker hood.
-
Reconnect the cooker hood to the mains by setting the group fuse to ‘1’ or placing this in the fuse holder.
-
Within 5 seconds, touch the lighting key until the lighting is on.
-
Within 5 seconds, touch the extraction on/off key.
▷ Wait at least 10 seconds before you use the cooker hood.
▷ If the remote control is replaced, repeat the steps for linking the remote control. If present, the cooker hood can be connected to the power supply with the On/Off switch located at the top of the cooker hood.
Entering a new code for the cooker hood
When interference prevents the remote control from working properly, a new code can be entered. -
Touch the remote control’s (-) and (+) keys simultaneously for at least 10 seconds.
▷ The LED on the remote control lights. -
Once again, touch the (-) and (+) keys simultaneously within 3 seconds.
▷ The LED on the remote control flashes 3x. -
Work through the steps for linking the remote control. Replacing the battery
Remove the remote control’s cover and replace the battery with a battery of the same type and voltage. The battery is chemical waste and must be disposed of in a responsible manner and in accordance with government regulations.
MAINTENANCE
Cleaning
Note!
Before carrying out maintenance work, always disconnect the cooker hood from
the power supply by setting the group fuse in the meter cupboard to ‘0’ or
removing the fuse. If present, the cooker hood can also be disconnected from
the power supply with the On / Off switch located at the top of the cooker
hood.
The inside and outside of the cooker hood must be cleaned at regular
intervals. Do not use abrasive products. Do not clean with alcohol!
Note!
Failure to follow these instructions for cleaning the appliance and replacing
the filters can result in fire. Always follow these instructions! The
manufacturer is not liable for damage to the hood or damage caused by a fire
that is due to inexpert maintenance or the failure to follow the
aforementioned recommendations and the safety instructions
supplied with the appliance.
** Clean the cooker hood with a soft cloth with water and a little
detergent. Then wipe with clean water. Do not use corrosive cleaning agents
such as soda, and do not use scouring sponges or similar. Treat with a product
designed for the maintenance of stainless steel and polish in the direction of
the surface finish of the stainless steel.
Metal grease filters**
Metal filters must be cleaned once per month (or when the filter cleaning
indicator – if present on the model – indicates that this is necessary). Clean
the filters with neutral cleaning agents, by hand or in the dishwasher at low
temperatures and with a short program. Put the grease filters in the
dishwasher with the openings facing down so
that the water can drain. Aluminum grease filters will become dull from the
cleaning agents in the dishwasher. This is normal and does not affect
performance.
The saturation of the filter depends on the intensity of use, the manner of
cooking and the regularity with which the grease filters are cleaned.
Grease filters
Clean the grease filter at least once a month. Cleaning will result in the
aluminum parts of the filters becoming dull due to the use of cleaning agents,
in particular when cleaning in a dishwasher. This is normal and is not covered
by the warranty.
Removing the grease filter
1. Switch off the cooker hood.
2. Pull the handle of the grease filter towards you and tilt the front
downwards.
Important:
The odor filter is clamped on top of the grease filter. Prevent the odor
filter from falling on your hob by supporting it when installing and removing
the filters.
Odor filter
-
Remove the grease filter.
-
Mount the odor filter.
Important:
The odor filter is clamped on top of the grease filter. Prevent the odor filter from falling on your hob by supporting it when installing and removing the filters.
-
Fit the grease filter.
Important:
- The saturation of the filter depends on the intensity of use, the manner of cooking and the regularity with which the grease filters are cleaned.
- The odor filter must be replaced at least once every four months.
- Odor filters cannot be washed for reuse. Saturated carbon is not environmentally friendly, so replace the filter in time.
As a replacement odor filter, you can opt for a long-life filter, recognizable
by the green plastic. This filter must be cleaned every 4 months.
The filters can be washed by hand or in the dishwasher at a maximum
temperature of 65 °C. The washing cycle must be done without other dishes and
without dishwasher detergent. Do not use any cleaning agents!
Remove excess water. Be careful to avoid damaging the filter. Place the filter
in the oven to dry for at least 1 hour at a maximum temperature of 80 °C.
After 4 times of use (or if the filters are damaged), the filters will need to
be replaced.
Lighting
This hood is fitted with a light system. This light system has to be replaced
by an authorized technician. Do not attempt to replace it by yourself.
The lamp in this household appliance is only suitable for illumination of this
appliance. The lamp is not suitable for household room illumination.
General
This appliance must be connected to the mains by a recognized installer who is
familiar with and works in accordance with the applicable safety regulations.
This appliance meets the requirements of European regulations.
Important information:
- The lowest part of the cooker hood must be at least 65 cm above the cooking surface of the hob.
- Take account of local regulations governing the ventilation of gas appliances.
- Before drilling holes, check to make sure that there are no wires in the area.
- The installation material supplied with this cooker hood is suitable for fastening to concrete and reinforced concrete ceilings.
Connection
Electrical connections
This appliance must be plugged into an earthed wall socket. Check to make sure
that the voltage specified on the type plate matches the mains voltage. The
appliance must be connected to the mains as follows:
BROWN = L (live)
BLUE = N (neutral)
GREEN/YELLOW = Earth
Note:
When you wish to make a fixed connection to the mains, you must make sure that
a multipolar switch with a break contact distance of at least 3 mm is fitted
in the power cable.
Dimensions
Assembly
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Disposal
Disposal of packaging and appliance
Sustainable materials were used in the manufacture of this appliance. At the
end of its life cycle, this appliance must be disposed of in a responsible
manner. You can obtain more information from the authorities.
The packaging of the appliance is recyclable. The following materials may have
been used:
- cardboard;
- polyethylene foil (PE);
- CFC-free polystyrene (PS hard foam).
These materials must be disposed of in a responsible manner and in accordance
with government regulations.
The appliance is marked with a crossed-out wheeled bin symbol to draw your
attention to the requirement for the separate disposal of domestic electrical
appliances. This means that the appliance may not be disposed of in unsorted
household waste at the end of its service life. The appliance must be taken to
a special municipal waste processing location for separated waste or to a
dealer who provides this service.
Collecting and disposing of domestic appliances separately avoids the
potentially detrimental consequences for the environment and health that can
result from unsuitable processing. This ensures that the materials used to
make the appliance can be recovered and that substantial savings in the use of
energy and raw materials can be achieved.
Declaration of conformity
We hereby declare that our products conform to the applicable European
Directives, Regulations and requirements, as well as all requirements in the
standards to which reference is made.
The appliance rating label is located on the inside of the appliance.
When contacting the service department, have the complete type number to hand.
Addresses, phone number of the service organization and the warranty
conditions can be found at www.etna.nl or
www.etna.be
www.etna.nl
www.etna.be 789363 / VER 3 / 07-08-2019
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>