Shenzhen Zfx Technology ZP-THP60 Wireless Headphone User Guide

ZP-THP60-Gamma4A
PRODUCT INFORMATION GUIDE

PRODUCT OVERVIEW

1. Pogo-pin for charging
2. Adaptive design headband
3. Micro USB cable for charging
4. RCA to 3.5mm cable
5. Soft Ear cushion
6. Wireless Transmitter&charging baser
7. Adapter
8. Charging LED indicator(Base station)
9. Connect LED indicator（Base station）
10. Pogo-pin for charging(Headphone)
11. 3.5mm input for wired use
12. Build-in mic(optional)
13. Micro-USB for charging(Headphone)
14. LED Indicator(Headphone)
15. Volume down
16. Mute
17. Power
18. Volume up
19. Power switch(Base station)
20. 20. Micro-USB for power
21. Audio source switch(Optical/3.5mm)
22. 3.5mm input
23. Optical input

SETUP

1. Use the Micro-USB cable to connect the Adapter and Base station for power-up
2. Power up the headphone, and will see the LED indicator on the headphones and the Base station turn to solid Blue

3.5mm Audio source

1. Use the RCA to 3.5mm cable to connect your TV(RCA output Jack/headphone jack) to Base station(3.5mm Input jack)
2. You can also use a 3.5mm to 3.5mm cable to connect the Mobile/soundBar to Headphones directly Optical audio source
   •Use the OPTICAL cable to connect your TV(optical output) to the Base station(optical input)
   •Select the audio output to optical in your TV setup menu.

CHARGING

1. You can hang the headphone to the base station for charging, make sure that the headphone and the base are incorrect contacts, and the charging indicator light is on. You can also charge the headset to use the micro-USB cable to the charging port on the headset, and plugging the other end into any USB power source(5V/1A)
2. LED indicator will be Red when charging, and will be off when charging full.

• The headset will turn off automatically when the power exhausted

POWER ON/OFF

To power on the headset press and hold the power button for at least 3 seconds. The LED indicator will Blue.
To power off the headset press and hold the power button for at least 3 seconds. The LED indicator will off.

PAIRING

• Press and hold the headset microphone mute button for 3 seconds at the same time, you will see the LED indicator blue blinking
• Press and hold the transmitter pairing button for 3 seconds until the LED indicator blue blinking rapidly
• Pairing will be completed automatically, and there is no need to pair again for use

The headset is already paired to the transmitter when it arrives.

Press and hold the headphone& Wireless transmitter pairing button for 3 seconds, you will see the LED indicator blinking and Turn Blue, the paring will be done.

OTHER CONNECTIONS FOR WIRELESS AUDIO

Connect To TV

Connect To SoundBar/Other Audio equipment

www.zfxtech.cn
Copyright © 2007-2019 ZFX TECH. All Rights Reserved

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

References

• 声粹声学

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>