Kimex 133-1120 Extender HDMI 2.0 over IP FULLHD 120m User Manual

Table of Contents

Kimex-133-1120-Extender-HDMI-2-0-over-IP-FULLHD-120m-
PRODUCT

All brand names and trademarks are properties of their respective owners.

Transmitter

Kimex-133-1120-Extender-HDMI-2-0-over-IP-FULLHD-120m-
FIG-1

IR Out: plug the IR blaster into this jack
IR In: plug the IR receiver into this jack
HDMI Input: connect to the HDMI output of your HDMI source device
Status: This LED illuminates to indicate the status of this transmitter
Power LED: This LED illuminates when power is applied to the transmitter.
Reset: press and hold this button for about 10 seconds to reset the transmitter to the factory default settings
DC/5V: plug one of the included AC power adapters into this DC jack
Ethernet: Connect a cat5e/6 Ethernet cable into this port to deliver the signal to the receiver

IR Out: plug the IR blaster into this jack
IR In: plug the IR receiver into this jack
HDMI output: connect to the HDMI input of your HDMI sink device
Status LED: this LED illuminates to indication the status of this receiver
Power LED: this LED illuminates when power is applied to the receiver
Reset: press and hold this button for about 10 seconds to reset the receiver to the factory default settings
Ethernet: connect a cat5e/6 Ethernet cable into this port to receive signal from the transmitter
DC/5V: plug one of the included AC power adapters into this DC jack

This HDMI over IP Extender use the advanced M-JPEG as the compression type, which makes it occupy lower bandwidth and transmit over the LAN more smoothly.
It supports 120m over single cat5e/6 cable at point to point, as well as point to many over Ethernet switch.
The over IP solution is widely used in various locations, like meeting rooms, classroom, metro, airport, home, mall advertisements…etc.

Using M-JPEG compression encoding, support resolution up to 1080p@60hz
Comply with TCP/IP protocol, Transmit up to 120meters@1080p/60Hz over single Cat5e/6 cable
Support LPCM audio format
Bi-direction Wide-band IR pass through to control the source or sink device. (38khz to 56khz)
Support one to one or one-to-many modes with large cascade
HDCP Compliant
Support PC web control
Build in EDID
Carry power to Tx and Rx units with a Power Over Ethernet enabled Smart Managed Switch (*Optional POE version only)

one-to-one extender

Kimex-133-1120-Extender-HDMI-2-0-over-IP-FULLHD-120m-
FIG-3

one too many extenders & Splitters

Kimex-133-1120-Extender-HDMI-2-0-over-IP-FULLHD-120m-
FIG-4

one-to-one extender

Connect the source device and the Transmitter unit with HDMI Cable.
Connect another HDMI display and the HDMI Receiver unit with HDMI Cable.
Connect the Transmitter and Receiver with the Cat5e/6 cable
Connect the IR blaster cable into “IR Out” port, and connect the IR Receiver cable into the “IR In” port. Then you can control the source or sink device with IR.
Power on the Transmitter and Receiver with 5V adapter.

NOTE: Insert/Extract cables gently.

Connect the source device and the Transmitter unit with HDMI Cable.
Connect the transmitter and the switch/router with a cat5e or cat6 cable.
Connect all the Receivers and the switch/ router with the Cat5e/6 cable.
Connect the HDMI displays and the HDMI Receiver units with HDMI Cable.
Connect the IR blaster cable into “IR Out” port, and connect the IR Receiver cable into “IR In” port. Then you can control the source or sink device with IR.
Power on the Transmitter and Receiver with 5V adapter, power on the switch with its adapter.