ascom NUWPC3 Wireless Pull Cord Module Installation Guide

June 6, 2024
Ascom

NUWPC3 Wireless Pull Cord Module

PRELIMINARY
INSTALLATION GUIDE Wireless Pull Cord Module (NUWPC3­Hx)

Mounting

7. Adjust the length of the cord: · Lift the bottom barrel of the cord (item 1). · Cut the cord about 2.5cm (1 in) below the desired length (item 2). · Tie a double knot at the end of the cord by looping the end of the cord twice through the loop (item 3). · Pull the knot tightly (item 4).

2.3 Placing of batteries
1. · Open the battery door of the base (item 1). · Remove the battery pack from the base (item 2). The battery pack is kept in place by a small edge. Lift the pack over this edge.

2. Place 2 x 1.5V AA disposable Alkaline batteries (not included) in the battery pack, pay attention to the polarity of the batteries.

TD 93427EN / 30 October 2020 / Ver. PA4

6

Mounting

PRELIMINARY
INSTALLATION GUIDE Wireless Pull Cord Module (NUWPC3­Hx)

The NUWPC3 is protected against reverse polarity of the batteries.
When batteries other than the recommended ones are used, the NUWPC3 is protected by a thermistor (PTC). The correct working cannot be guaranteed.
3. · Place the battery pack back into the base (item 1). Lift the battery pack into the module and place it over the small edge to keep it in place. · Close the battery door. (item 2)

The battery pack fits only one way into the base.
When the battery pack is inserted, the 3 button LEDs will light up in sequence starting with the top LED. This confirms that the module is working properly. 4. Check the correct working of the module: Generate a call by pulling the cord. Only in a correctly configured system will the call generate an alarm on display devices such as corridor lamps.
5. For new installation: Place the 2 provided screw caps over the screw holes. Orient them correctly. The caps have a small protrusion that fits neatly into the small indentation of the module, see detail below

2.4 Removing the module
Removal of the NUWPC3 from wall or ceiling. 1. Remove the battery pack from the module:
· Open the battery door of the base (item 1).
7

TD 93427EN / 30 October 2020 / Ver. PA4

PRELIMINARY
INSTALLATION GUIDE Wireless Pull Cord Module (NUWPC3­Hx)

Mounting

· Remove the battery pack from the base (item 2). The battery pack is kept in place by a small edge. Lift the pack over this edge.

2. Remove the 2 screw caps: · Insert a small flat tipped screwdriver next to the cap (item 1). · Twist the screwdriver and pop out the cap (item 2).
3. Remove the 2 screws with a #2 Phillips screwdriver.

4. Pull the Module gently away from the base. The module is still connected to the base via the battery pack wires.
5. Disconnect the battery connector from the rear of the module

TD 93427EN / 30 October 2020 / Ver. PA4

8

Mounting

PRELIMINARY
INSTALLATION GUIDE Wireless Pull Cord Module (NUWPC3­Hx)

2.5 Replacing the button insert
1. Remove current button insert by gently pulling the small tab at the lower end of the insert with a small pair of pliers.

2. Insert a new button insert from the lower end of the module. Make sure the insert fits completely in the membrane. The button insert should be water resistant.
3. Check that all of the button LEDs are visible: Remove the battery pack and insert again: the 3 button LEDs will light up in sequence starting with the top LED. This confirms that the module is working properly.

9

TD 93427EN / 30 October 2020 / Ver. PA4

PRELIMINARY

10

TD 93427EN / 30 October 2020 / Ver. PA4

last page

PRELIMINARY

TD 93427EN / 30 October 2020 / Ver. PA4

Ascom (Sweden) AB Grimbodalen 2 SE­417 49 Göteborg Sweden Phone +46 31 55 93 00 www.ascom.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals