SENWA LS140L Smartphone User Manual
- June 6, 2024
- SENWA
Table of Contents
User manual
Model LS140L
General Information
1.1 Introduction
Please read this manual carefully to keep your phone in perfect condition. It
is important to familiarize yourself with the operation in its entirety to
ensure proper use and the best result. Sanwa Mobile is not responsible for
inappropriate use of the phone.
Sanwa Mobile may change the device without prior written notice and reserves
the right to interpret the performance of the phone.
Due to different versions of software and operators, the appearance of your phone may be different from that shown here; please refer to your phone for details.
1.2 Safety warnings
KEEP THE PHONE OUT OF THE REACH OF CHILDREN
Keep the phone and all its accessories out of the reach of small children to avoid choking hazards.
SAFETY ON THE ROAD IS A PRIORITY
Do not use the phone while driving. Use a hands-free kit if you need to make
or receive an important call and are driving. In some countries, calling or
receiving calls while
driving is illegal.
TURN OFF THE PHONE ON THE PLANE
Wireless devices can cause interference on airplanes. Using a mobile device
during a flight is illegal and dangerous. Please make sure your phone is
switched off during the
flight.
TURN OFF YOUR PHONE WHEN ENTERING DANGEROUS AREAS
Strictly observe the laws, codes, and regulations on the use of mobile devices
in risk areas. Turn off your phone before entering a potentially explosive
place, such as gas
stations, oil depots, chemical plants, or places where any flammable or
explosive material is handled.
OBSERVE ALL SPECIAL REGULATIONS
Follow the special regulations in force in each case, such as in hospitals, and always switch off your phone when its use is prohibited or when it may cause interference or be dangerous in any way.
MEDICAL EQUIPMENT
Use the phone with caution near medical devices, such as pacemakers, hearing aids, and other electronic medical devices, as the phone may cause interference in these types of equipment.
INTERFERENCES
The quality of conversation on any mobile device can be affected by radio
interference. Inside the phone, there is an antenna located on top of the
phone; Do not touch the
antenna area during a conversation to avoid possible deterioration in sound
quality.
QUALIFIED SERVICE
Only qualified personnel can repair the device. Repairing the phone yourself can be dangerous and invalidates the warranty.
ACCESSORIES AND BATTERIES
Use only official accessories and batteries. After the battery charge is
complete, do not leave your phone connected to the power source for a long
period of time; the phone is
not designed to remain connected to the power source for a long time and doing
so could damage the device or be dangerous.
OBSERVE LOCAL REGULATIONS
Use the telephone in a sensible and appropriate way, respecting the laws, norms, uses, and customs of each area.
EMERGENCY CALLS
Make sure the phone is switched on and in service, enter the emergency number
(it will vary depending on the country you are in), and then press the dial
key. Please indicate
your location and state your situation briefly. Do not end the call until
instructed to do so.
Note: Like all other mobile devices, this phone does not necessarily support all the functions described in this manual in case of mobile network transmission problems. Also, some networks do not yet support the emergency call service. Therefore, do not rely solely on the mobile phone for essential communications, such as first aid. For more information, consult your local network operator.
AIRBAGS
Do not place the phone or its accessories in the expansion area of the car airbags; doing so could injure you if the airbag system is activated.
TAKE CARE OF YOUR HEARING CAPACITY AND YOUR VISION
When using the headset, be sure to adjust the volume carefully, avoiding
listening to music at a volume that is too high as it may damage your hearing.
Also, do not place the
the screen of your phone too close to your eyes and try to keep any lights on
in the environment while using it.
1.3 Precautions
This phone is carefully designed with detailed finishes. Please be especially
careful when using it. The following tips will help extend the life of your
phone and ensure that
it survives the warranty period:
Keep the phone dry and away from rain, moisture, and any other liquid
substance that can oxidize electronic circuits.
Do not use or store the phone in places with dust or other suspended
particles, to avoid damage to the device.
Do not expose the phone to any heat source, such as radiators or dryers. High
temperatures shorten the life of electronic circuits and damage the battery
and some
plastic parts.
Do not store the mobile phone in extremely hot or cold environments. This
phone is designed for use in environments with ambient temperatures ranging
from 0ºC (32ºF) to 35ºC (95ºF); Continued exposure to very high or low
temperatures can cause moisture to build up inside the phone, damaging
electronic circuits when moving from a cold area to a warmer area and
shortening the life of the battery and device.
Do not throw or hit the phone, as it may destroy the internal circuitry and
high-precision components that make it up.
Your phone can be inspected by X-ray machines, such as those used on conveyor
belts at airport checkpoints, but it should not be exposed to magnetic
detectors or
hand-held scanners.
Do not use cleaning products to clean your phone. Use only a clean, dry cloth.
Don’t paint your phone. This could obstruct moving parts and vents or vents on
your device.
Your Phone
2.1 Phone overview
1| Handle charging connection| 11| Direct access key: access to the previous
block function
---|---|---|---
2| antenna| 12| Support frame back cover
3| display screen| 13| Hanging area
4| Navigation key| 14| Battery area
5| Left function selection key: enter the menu to confirm| 15| Handle earpiece
area
6| Right function selection key: enter call log/return| 16| Handle charging
connection
7| Dial key: dial/into call log| 17| Handle display area
8| Power button: power on/off| 18| Handle button area
9| Number keys and character input| 19| Handle to send MIC area
10| Direct access key: access the next block function| |
2.2 Key functions
The phone contains the following keys:
On/off key
The power key is located on the right side of the keyboard. Press once to turn
off the screen and lock the phone after use. If you press and hold the key,
the phone will turn
off.
Call key
The call key is located on the left side of the keyboard. Press once to view
call logs.
Select keys
The selection keys are located on the upper left side and the upper right side
of the keyboard. Press the left selection key to access the Menu. Press the
right selection key
to go Back (previous screen) or go to the Log from the main screen.
Navigation keys
The navigation keys are located in the center of the keyboard. Press the
navigation keys to scroll and select Menu and submenus items.
Numeric keys
The number keys are located in the lower half of the keyboard. Press each
number key to enter the numbers on the dial pad.
Volume keys
The volume keys are located on the navigation keys. Use the up and down
navigation keys to increase and decrease the volume during a call or while
listening to various audio formats. To edit the volume settings, go to Menu->
Settings-> Profiles. It shows different options such as: Normal, Silent,
Vibrate, Indoor, Outdoor, Headphones, and Bluetooth.
Shortcut keys
The shortcut keys are at the bottom of the keyboard. Each hotkey is a shortcut
to important applications.
2.3 Main Menu
| Mi Telcel| | Calculator
---|---|---|---
| File Explorer| | Settings
| Browser| | Chat
| Multimedia| | SIM Telcel
| Tools| | Messaging
| History| | Contacts
| Registro de Ilamadas| | Multimedia
---|---|---|---
| SIM Telce| | Navegador
| Contactos| | Radio FM
| Reproductor de musica| | Juegos
| Portal Claro Ideas| | Extras
| Mensajes| | Ajustes
Note: The appearance of the application icons may vary when updating the software.
You will find a series of icons that indicate the status of your phone.
Icons|
Descripcion
---|---
| Nivel de senal de red actual
| Instalar una tarjeta SIM
| Eventos para hoy
| Nivel de carga de la bateria
| Tiene un Mensaje no leido
| La Alarma este activada
****| Silencioso esta activado
| Perfil Vibrar esta activado
| Perfil Interior esta activado
| Perfil Exterior este activado
First Steps
3.1 SIM card installation
A SIM card carries useful information, including your mobile phone number, PIN (Personal Identification Number), network information, contact information, and short message information. You will need an active SIM card to be able to make phone calls with your phone.|
Note: After turning off your phone, wait a few seconds before removing or inserting a SIM card. Take special care when handling the card as friction or bending can damage it.
SIM card installation:
Turn off your phone and remove the battery cover.
Insert the SIM card into the SIM card slot carefully, with the truncated corner of the slot aligned until the card cannot be inserted further. Optionally, put in a microSD card.
Note: Both the SIM card and the SD card are tiny objects. Keep them out of the reach of children to avoid choking hazards.
3.2 Charging the battery
The remaining battery charge is indicated by a white battery icon in the upper right corner of the screen. When the charge level is too low, the phone displays the message “Low battery”.
Charger use:
Place the battery correctly in the phone before charging.
Connect the charger cable to the Micro USB port on the bottom.
Insert the charger into a suitable socket.
During charging, the icon on the screen will “blink” to indicate charging. The
loading animation disappears when the loading process is complete.
Note: The battery powers the phone for a limited period of time. Make sure the battery is fully charged before using the phone. Make sure that the charger plug and the USB cable plug are inserted in the correct direction. Inserting them in the wrong direction may cause charging failure or other problems. Before charging, make sure that the standard voltage and frequency of the local mains supply match the rated voltage and power of the charger.
3.3 Installation of the antenna
Connect the external antenna to the corresponding port until it is firmly in
place, as shown in the figure below.
Note: Use the provided external antenna connection only. Using an antenna
that is not compatible with the device may cause damage to the device.
3.4 Telephone base assembly
Phone Base Stand: Please open outward from the bottom of the base card stock to keep the phone obliquely level on the desk.
Using the phone
Change the method in Spanish
During regular use of your phone, there will be times when you will need to
enter text over and over again. Your phone allows you to enter text, letters,
numbers or symbols (including punctuation marks). In any text editor, press
the # key to change the input method.
Entry method in Spanish
Your LS140L phone has multiple input methods in Spanish. When you are typing
in a text field, press the # key to change the method.
The methods available with predictive text are automatic uppercase (Sp),
uppercase (SP), and lowercase (sp). Without predictive text, you have
automatic capitalization (Abc), uppercase (ABC) and lowercase (abc). It also
has the numeric input method (123).
Enter symbols and punctuation marks In any of the text input methods press the key.
- (asterisk) to display the list of available punctuation marks and symbols.
Enter a space
In any of the text input methods press the key.
0 (zero) to enter a space.
Connecting to Wi-Fi networks
The Wi-Fi function allows you to connect your phone to the internet through
Wi-Fi networks.
The phone will search for available Wi-Fi networks in its range. Tap a network to connect to it. If the network is open, you will be asked to confirm that you want to connect to that network. Secure networks are indicated by a padlock icon in which a password is entered.
Connect to Bluetooth devices
The Bluetooth function allows you to connect your phone to compatible Bluetooth wireless devices.
Before using a Bluetooth device with your phone, you must pair it. The phone will search for and display the identifiers of all visible Bluetooth devices in range. If the device you want to pair with is not listed, make it visible by following the instructions in the manual for the device in question. Once you pair your phone with the device, the devices will remain paired unless manually unpaired.
Connect the Bluetooth of the LS140 desk phone with the Bluetooth of the handle:
-
When the handle is turned on, press and hold the power button to turn on, the prompt tone prompts to turn on, and there is a prompt tone when shutting down, there will also be a prompt tone when the connection is disconnected, and there will be a prompt tone when the distance to the landline is exceeded, return the effective distance to connect and prompt (The effective distance is within 10 meters)
-
The handle is turned on and not connected to the LS140 desk phone. The display status of Bluetooth pairing:
After the pairing is successful, the status bar of the landline will display a solid icon indicating that the Bluetooth has been successfully connected If it is not successfully connected, it will be grayed out
The handle is turned on and connected to the Bluetooth pairing of the LS140 landline:
When the phone is in a low battery state, the battery level will change, and a
low volume will be prompted. Please place the handle at the charging
connection point of the base phone to ensure that there is enough power to use
during the call. The low battery state may affect the clarity of the Bluetooth
call. Please pay attention.
Handle call can be switched to handle call or landline speaker call when the
landline is in the call option.
Connecting to a computer via USB
The phone can be connected to a computer using a USB cable to transfer music,
pictures and other files from your computer to your phone’s SD card and vice
versa.
Connect the phone to a computer using a USB cable. Select ‘LS140L USB Storage’
to view your files.
Claro Ideas Portal
To use the Portal Claro ideas application, you must first make sure that your SENWA LS140L phone has a SIM card installed correctly; then verify that your SENWA equipment has a signal from your network provider and finally verify that your telephone line has a balance.
Portal Claro ideas
Press the Menu option, select the Portal Claro ideas application with the navigation keys and press OK to open it. Wait for the main page of Portal Claro ideas to load and you will be able to see the content of the application: downloading tones, videos, sports news, etc. At the bottom of the screen you will find the Option and Stop keys.
Option
By pressing the Option key you will find the following menus.
Update: With this option you can update the content of Portal Claro ideas.
Exit: Selecting this option will exit the Portal Claro ideas application.
Stop
Selecting this option will stop browsing within the Claro ideas Portal.
Note: The Claro Ideas Portal is only direct access; Portal Claro ideas is not an application to surf the internet, so you can only access links, links, and content from Portal Claro ideas. The download experience of the content of the Portal Claro ideas page will depend on your cell phone company.
Experience in the Portal Claro ideas application will depend on the quality of the network and coverage of your service provider.
Calls
Make a call to a number in contacts
Press the left selection key to access the Menu and then press the Contacts icon. Use the navigation keys to select the desired contact. Press the call key to make a call.
Make a call to a number from the call log
Press the left selection key to access the Menu and then press the Call Logs icon, or press the right selection key from the home screen for a shortcut to Call Logs. Use the navigation keys to select the desired contact. Press the call key to make a call.
Answer incoming calls
Press the left selection key or the call key to answer an incoming call, or press the right selection key twice or the power key once to reject a call.
Press the power key to hang up a call.
Manage multiple calls
To answer an incoming call in the middle of a conversation, you can press the call key to answer the new call and keep the first call on hold, or you can combine the two calls.
Note: During the call, use the icons at the bottom of the screen to
access Contacts, access the keypad, activate the hands-free speaker, mute the
microphone, but the call on hold, or record.
4.1 Lock and turn off the phone
To lock your phone and prevent unwanted keystrokes, press the power key once. To unlock, press the left selection key, then the asterisk * key. Depending on the security settings, the idle screen or the lock screen will be displayed directly.
To turn off your phone, press and hold the power key.
To lock the phone with a password, go to Menu -> Phone settings-> Security -> Phone locked and select your preferred password method.
IMPORTANT: Do not forget your password. If you forget it, you won’t be able to unlock your phone and you won’t be able to access your personal information. Sanwa Mobile is not responsible for the use of this function and the consequences that occur if the password is forgotten.
Multimedia and other Applications
Camera: You can choose two models: photography and video.
Image: View the images saved in the phone memory or on the memory card.|
Video: Use the video player function.
Tape recorder:
Start recording: Start audio recording.
List of recorded files: List of files in the phone memory or SD card
Memory: Set the storage memory.
File format: Set the format of the saved file.
FM Radio:
Automatic search: Search and save FM stations automatically.
Channel list: View the list of FM radio channels.
Save: Save a channel in the channel list.
Manual search: Search and save a channel automatically.
Activate loudspeaker: Select to activate the loudspeaker.
Play in the background: Select to activate background playback.
Record: Record the FM radio broadcast.
Record times: Set the time to record.
File list: View list of recorded FM files.
Help: Get help about the FM radio function.
Music: Play MP3 songs and audio files. To play the MP3 songs and audio files, press the Up and Down keys to adjust the volume, the Left and Right keys to select the previous or next song, and the OK key to play / stop the audio file or the song.
Music list: Access a playlist, being able to add and edit songs in the list
and perform other operations.
Add: Add songs or mark them as favorites in the playlist.
Set ringtone: Set an audio file or song as a ringtone or alarm.
Random: Play the songs randomly.
Repeat: Repeat one or all songs.
Settings: View the music player settings.
Exit
Games: Your phone includes a game. Check the game menus to learn how to play.
Additional features:
My Files: My Files allows you to view and manage files and folders stored both
in your phone’s internal memory and on the microSD card, when one is inserted.
Click a folder to view its contents and click the Back button to return to the
parent folder.
Wi-Fi: Connect your phone to the internet.
Calendar: Press the left selection key to access the calendar screen. The
first line shows the year and month, the third line shows the week, the middle
area shows the exact date of the month, and the last line shows the left and
right selection keys in the message.
Calculator: Perform arithmetic calculations in a simple, practical and
convenient way.
World clock: Check the time of different countries, stopwatch alarm, etc.
Stopwatch: allows you to measure time.
Bluetooth: Connect your phone with compatible Bluetooth accessories.
Memory management
Your phone has internal memory. These memories are sufficient for the use of the phone, but your phone is designed to work with a micro SD memory card that would improve the user experience and storage capacity. Micro SD cards are a cheap and efficient way to increase your phone’s memory.
Your phone supports cards up to 16GB, enough to store thousands of songs and photos.
The user is ultimately responsible for managing the phone’s storage. Sanwa Mobile is not responsible for the inappropriate use of the phone.
Troubleshooting
If you have any problem with your phone, before taking it to Technical Service make sure that you cannot solve your problem with any of the methods offered here. We advise you the following:
Charge the battery fully
Avoid cluttering your phone memory and SD card with photos, music or any other
type of data.
Use Factory data reset to erase all data on your phone and return it to its
initial settings, accessing Settings -> Phone settings-> Restore settings->
Enter a password.
(Note: Restore Settings will erase ALL of your personal data – make sure
you’ve made a backup before resetting your phone.)
Fallos comunes| Razones|
Soluciones
---|---|---
La bateria no see carga| El voltaje no se co- rresponde con el ran- go
especificado en el cargador.| Utiliceel voltajees- pecificado enelcar- gador.
EstA utilizando un cargador no homo- logado.| Utilice un cargador
disefiado especi- ficamente para su telefono.
La bateria no see carga| El cargador no esta bien conectado.| Verifique que el
en- chufe este conectado correctamente.
| |
Fallos comunes
| Razones|
Soluciones
| Tarjeta SIM dahada| Contacte con su ope- rador de red
Error de la SIM| Tarjeta SIM no insta- lada correctamente| Compruebe que
la tarjeta SIM esta bien colocada.
| La superficie metAlica de Ia SIM esta sucia| Limpie Ia tarjeta SIM con un
patio seco y limpio.
Errata
We invite you to read the Model LS140L User Manual before using the phone.
SENWA LS140L Telephone Information:
SENWA Landline Cell Phone, Model LS140
Unbranded antenna with TNC connector for LS140L telephone, 6-wire unmarked
RJ-11 cable for LS140L
SENWA model telephone base
S130 phone headset
SENWA Rechargeable Lithium-Ion Battery, LS140L model: 3.7 Vdc, 1000mAH,
AC / DC adapter, SENWA Brand, LS140L Model: Input 100-240Vac 50/60 Hz,
0.15A, Output: 5V, 500 mA
User Manual
Imported by:
SENWA MEXICO S.A. DE C.V.
CARRETERA MEXICO-TOLUCA No. 5324, INT. PLANTA BAJA
COL. EL YAQUI, CUAJIMALPA DE MORELOS
CIUDAD DE MEXICO, Mexico
WEB: WWW.SENWAMOBILE.COM
Twitter: @senwamobile
Facebook: SENWA mobile
Telephone: 01 800 01 SENWA (73692)
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to the user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Absorption Rate (SAR) information:
This device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluations of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. The use of belt clips, holsters, and similar accessories should not contain metallic components in their assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. This device complies with RF specifications when the device is used at 25mm from the body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>