SENWA 4G LTE CPE Router User Guide

SENWA 4G LTE CPE Router User Guide

Legal Information

Copyright @ 2019. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of and its affiliates. reserves the right change or modify any information or specification contained in this manual without prior notice and without any liability.

Limitation of Liability

Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, whether or not had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost.

Introduction of Router

your router is for indoor use only and multiple devices like computer, landline phone or mobile  phones can be connected to the router to access the Internet, make telephone calls and more.

Application Scenarios:

Scenario 1: 3G/4G mobile network service using a SIM card

Scenario 2: Data service from Ethernet cord Internet connection (Ethernet Port)

Scenario 3: Data service from Ethernet cord and VOLTE voice using a SIM card

Appearance

1. 1*LAN port
2. 1*WAN port
3. 1*Telephone port
4. 1* Micro USB
5. 1*Reset/WPS button
6. Power Input
7. Standard SIM card slot
8. 4G&WIFI external antenna ports
9. SYS indicator
10. ETH indicator
11. WiFi/WPS indicator
12. WAN(4G) indicator
13. NET indicator

Reset/WPS button: Press more than 3 seconds for Reset and Short press for WPS

Important: Router does not support Micro/Nano SIM card or any other non standard SIM cards.

Setup your Router

Inset a standard SIM card firstly as shown in the following diagram and then connect the power adapter to the power input of the router. Power on the router, and it will search for available mobile networks automatically. Do not inset or remove the SIM card when the router is running, as this may affect performance or damage the SIM card.

The intuitive indicators display the router’s status

Data transfer
WIFI/WPS| On: WiFi is enabled Off: WiFi is disabled Blinking: WPS connection set up in progress
WAN| On: Connected to the 4G network Off: Connected to the non-4G network.
NET| Wireless Dialing indicator On: Registered to a Network Off: No register to the Network Blinking: Data transfer

Configuring

You can configure the router using the WebUI Settings page.

1. Launch the Internet browser, and enter http://192.168.1.1 in the address bar.
2. Enter the password, and log in to the web management page. The default password is admi

You also can refer to the label on the backside of the router for the default IP address and password. It’s strongly suggested to change the default login password of the WebUI to prevent unauthorized users from changing the routers’ settings.

Connect to WiFi Network

You can connect your computer or mobile phone to the router’s WiFi network. Default SSID: 4G-CPE-2G-XXXX（XXXX is last 4 digits of MAC address）

Default Password: 12345678

It’s strongly suggested to change the default SSID and password by accessing to the WebUI WiFi management page to prevent unauthorized access to your WiFi network. You need to reconnect to the router’s WiFi network after changing the WiFi password.

Access the internet through the WAN port

You can connect the router’s WAN port to the wall-mounted Ethernet port by Ethernet cable, and then choose the working mode to be Broadband mode and configure the PPPoE/Static/DHCP parameters to access to internet.

VOLTE, VOIP & CS Domain Voice Call

The router supports VOLTE, VOIP and CS domain voice call services. To change the call mode select Settings > Phone and chose the desired option from the dropdown menu.

For best results, the “Auto” setting of network mode is recommended. Please contact your network service provider for more detailed information.

FAQS & Troubleshooting

If you are expecting any issues with the router, in most cases please try to restart the router or restore the router to its factory settings. The illustrations in this guide are for reference purpose only and may not reflect the exact appearance of your product. Please contact your network service provider for more detailed

information.

button for approximately 3 seconds using a pointed object until the indicator starts to blink. Restoring factory settings will clear all customized settings.
How can I connect to the router by Wi-Fi Protected Setup (WPS) function?|

1. Ensure that WiFi is enabled on the client.
2. Press the WPS button on the router to set up a WPS connection

How to deal with the content display issue of the WebUI?| Manually clear browser’s cache, for example, open your browser and choose Internet Options

General >Browsing history >Delete, and re-launch the WebUI page.
Why the router does not work after I have finished configuring?|

1. Ensure that you have a working standard Sim card inserted properly.
2. Move the router to an open space free from obstructions and make sure there are available mobile networks.
3. If the problem persists, please contact your network service provider.

Why can’t I access the router’s WebUI?|

1. Ensure that your computer is connected to the router through WiFi or the Ethernet cable.
2. Ensure that your computer is set to obtain an IP address and DNS server address automatically.
3. Restart your browser or try using another browser.
4. If the problem persists, restore the router to factory settings and try to access WebUI again.

Warning and Notice

Safety Precautions

• This section contains important information about the operation of your device. It also contains information about how to use the device safely. Read this information carefully before using your device.
• Some electronic devices may be susceptible to electromagnetic  interference. Locate therouter away from any TV set, radio and other electronic equipment to avoid electromagnetic interference.
• The router may interfere with medical devices, such as hearing aids and pacemakers. Consult a physician or the manufacturer of the medical device before using the router.
• Please keep yourself at least 20 centimeters away from router.
• Do not use your router in dangerous environments such as oil terminals or chemical factories where there are explosive gases or explosive products being  processed.
• Please use original accessories or accessories that are authorized by . Unauthorized accessories may affect the router performance, damage the router or cause danger to you.
• Do not attempt to dismantle the router. There are no user serviceable parts.
• Do not allow the router or accessories to come into contact with liquid or moisture at any time. Do not immerse the router in any liquid.
• Do not place objects on top of the router. This may lead to overheating of the device.
• The device must be placed in ventilation environment for use.
• Do not expose the router to direct sunlight or store it in hot areas. High temperature can shorten the life of electronic devices.
• Do not allow children to play with the router or charger.
• Keep the length of the cable between the router and the phone less than 10 meters.
• The router is for indoor use only. Do not use the router outside. Do not connect telephone extensions which run outside of the building. These can result in lightning damage to your unit.

Cleaning and Maintaining

• Use an antistatic cloth to clean the router. Do not use chemical or  abrasive cleanser as thesecould damage the plastic case. Turn off your router before you clean it.
• Use the router within the temperature range of 0℃～ +45℃, and the storage temperature range is -20℃～+70℃. The humidity range is 5%~95%.
• Do not remove your SIM card unnecessarily. The SIM card may be easily lost or it can be damaged by static electricity.

FCC Warning

15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning for Mobile device:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated withminimum distance 20 cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>