Honeywell SOMAT39 Luzon Wi-Fi and BT Module User Manual

Honeywell SOMAT39 Luzon Wi-Fi and BT Module

Introduction

This document specifies the details for a WiFi 802.11a/b/g/n/ac with BT4.1 RFSOM module called with Honeywell Part No. uzon Module will use WM-BAC-AT-39 USI SiP module with Qualcomm QCA6174A chip set which includes LNA, switch, and internal power amplifier VSWR. The module will perform with all legacy hardware having data rates as low as 1Mbps. This chipset also supports concurrent operation of Bluetooth (Version 4.1) for wireless connectivity during browsing or other device applications. Along with both standard and high speed (HS) Bluetooth data rates, Bluetooth low energy modes are also supported. Hardware WAPI acceleration engine, AES, TKIP, WPA and WPA2 are supported to provide the latest security requirement on your network. For placing the SOMAT39 onto the carrier board, the part number to be used is SOMAT39 is meant to be used inside Honeywell only. It
is not meant or designed to be sold independently outside Honeywell

SOMAT39 – System on Module Features

• IEEE 802.11 a/b/g/n/ac WLAN
• Bluetooth 4.2 + HS
• Bluetooth-WLAN coexistence
• WiFi Wake on Wireless (WoW)
• 20/40 MHz bandwidth at 2.4GHz
• 20/40/80 MHz bandwidth at 5GHz
• Internal PA/LNA
• RF SOM Size: 15 mm x 15 mm, LGA Package
• 802.11 k/v/r [will be available in next release]
• Low Current consumption in IEEE PS and Deep Sleep
• WiFi Security methods: OPEN, WEP, WPA2-PSK, WPA2-1X (PEAP-MSCHAPV2, PEAP-TLS, EAP-TTLS)
• WiFi + BT Coexistence with simultaneous video streaming over WiFi and voice call over BT.
• Weight of module ~ 1gram
• Featuring integrated IEEE 802.11 a/b/g/n/ac + BT4.1.
• 60 pins LGA.
• Future to support two streaming dual-band antennas.
• Low power consumption & excellent power management performance extends battery life.

Block Diagram

SOMAT39 module is designed based on Qualcomm QCA6174A chipset solution. It supports a generic SDIO, UART interface to connect the WLAN/BT to the host processor. A simplified block diagram of the WM-BAC-AT-39 module is depicted in above picture.

Technical Specifications

Absolute Maximum Rating

Maximum RF input

(reference to 50 Ω input):

| 0dBm
Digital I/O input voltage for

3.3 V I/O supply:

| Vdd + 0.3 V
Digital I/O input voltage for

1.8 V I/O supply:

| Vdd + 0.2 V

Recommended Operating Condition

(*1.8V for higher > 50MHz SDIO clock versions)

Current Consumption| Tx output power @ 19 dBm on 11b 1M (single stream): 420mA (typ), 490mA (max)

**Tx output power @ 16 dBm on 11n MCS8_HT20 (dual stream): 620mA (typ), 720mA (max)

Tx output power @ 15 dBm on 11n MCS0_HT20 (single stream-5g): 470mA (typ), 540mA (max)

**Tx output power @ 13 dBm on 11n MCS0_VHT80 (dual stream-5g): 715mA (typ),820mA (max)

|
** Dual Streaming Current Consumption Data is for reference purpose only. Existing capability for SOMAT39 is enabled for single streaming only.

NOTE: Peak current bursts of 1.1A is observed during tests. Power supply input to RFSOM must support peak current of 1.1A.

NOTE:
Peak current bursts of 1.1A is observed during tests. Power supply input to RFSOM must support a peak current of 1.1A.

Foot Print, Front & Back view

Note: Bottom View of RF SOM Module – LGA Package Footprint

Pin Configurations

(WiFi/BT)

| RF Output| RF Antenna 0 WiFi/BT Output
12| GND| Ground| Ground
13| IO7| Input/Output| LTE_SYNC_TMS
14| IO8| Input/Output| BT_PCM_IN
15| IO9| Input/Output| BT_PCM_CLK
16| IO10| Input/Output| BT_PCM_SYNC
17| IO11| Input/Output| PCIE_WAKE_L
18| IO12| Input/Output| PCIE_CLKREQ_L
19| IO13| Input/Output| PCIE_RST_L
20| IO14| Input/Output| LTE_PRI_TCK
21| IO15| Input/Output| USB_DN
22| IO16| Input/Output| USB_DP
23| VDD1| Power Supply| Power Supply for IO’s
24| GND| Ground| Ground
25| PCIE_REFCLK_P| Clock Diff. Input +ve| PCIE Clock Diff. input Positive
26| PCIE_REFCLK_N| Clock Diff. Input -ve| PCIE Clock Diff. input Negative
27| GND| Ground| Ground
28| PCIE_TX_P| Transmit Diff. Output +ve| PCIE Transmit Diff. Output Positive
29| PCIE_TX_N| Transmit Diff. Output -ve| PCIE Transmit Diff. Output Negative
30| GND| Ground| Ground
31| PCIE_RX_N| Receive Diff. Input -ve| PCIE Receive Diff. Output Negative
32| PCIE_RX_P| Receive Diff. Input +ve| PCIE Receive Diff. Output Positive
33| GND| Ground| Ground
34| IO17| Input/Output| LTE_ACTIVE_TDI
35| IO18| Input/Output| SDIO_INT_TDO
S.No| RF SOM SOM

PINOUT

| Signal Type| Signal Description
---|---|---|---
36| VDD2| Power Supply| Power Supply – SOM VDD3V3
37| VDD3| Power Supply| Power Supply – SOM VDD3V3
38| SDIO_DATA_0| Data Bidirectional output 0| Serial Data IO Data 0
39| SDIO_DATA_1| Data Bidirectional output 1| Serial Data IO Data 1
40| SDIO_DATA_2| Data Bidirectional output 2| Serial Data IO Data 2
41| SDIO_DATA_3| Data Bidirectional output 3| Serial Data IO Data 3
42| SDIO_CMD| SDIO Command input| SDIO Command input
43| SDIO_CLK| SDIO Clock input| SDIO Clock input
44| GND| Ground| Ground
45| IO19| Input/Output| BT_UART_TXD
46| IO20| Input/Output| BT_UART_RXD
47| IO21| Input/Output| BT_UART_CTS
48| IO22| Input/Output| BT_UART_RTS
49| GND| Ground| Ground
50| GND| Ground| Ground
51| GND| Ground| Ground
52| GND| Ground| Ground
53| GND| Ground| Ground
54| GND| Ground| Ground
55| GND| Ground| Ground
56| GND| Ground| Ground
57| GND| Ground| Ground
58| GND| Ground| Ground
59| GND| Ground| Ground
60| GND| Ground| Ground

Wireless Specifications

WLAN
The SOMAT39 module complies with the following features and standards;

4.900 GHz – 5.845 GHz

Number of Sub

Channels

| 1~ 11Channels

36~ 48,52~ 64, 100~ 140, 149~ 165 Channels

Modulation| DSSS, CCK, OFDM, BPSK, QPSK,16QAM, 64QAM
Supported data rates| 1, 2, 5.5, 11 (Mbps)

6, 9, 12, 18, 24, 36, 48, 54 (Mbps) HT20_MCS0 ~ HT20_MCS7

VHT80_MCS0 ~ VHT80_MCS9

BLUETOOTH
The Radio specification is compliant with the Bluetooth 2.1 + EDR specification

WLAN Radio Specifications

Mode

| Data      rate (Mbps)| Channel Frequency (MHz)|

Set Power

---|---|---|---

802.11b

|

1

| 2412| 19
2442| 19
2462| 19

11

| 2412| 19
2442| 19
2462| 19

802.11g

|

6

| 2412| 19
2442| 19
2462| 19

54

| 2412| 19
2442| 18
2462| 16

802.11n

|

MCS0_20

| 2412| 19
2442| 19
2462| 16

MCS7_20

| 2412| 19
2442| 18
2462| 16

802.11n

|

MCS0_40

| 2422| 19
2442| 16
2457| 15

MCS7_40

| 2422| 19
2442| 16
2457| 15

Mode

|

Data rate

|

Channel Frequency

| Set Power dBm|

Mode

|

Data rate

|

Channel Frequency

| Set Power dBm|

Mode

|

Data rate

|

Channel Frequency

| Set Power dBm
---|---|---|---|---|---|---|---|---|---|---|---

802.11a

|

6Mbps

| 5180| 16|

802.11n

|

MCS0_40

| 5190| 14| |

MCS9_20

| 5180| 15
5240| 16| 5230| 14| | 5240| 15
5260| 16| 5270| 14| | 5260| 15
5320| 16| 5510| 14| | 5320| 15
5500| 16| 5590| 14| | 5500| 15
5600| 16| 5670| 14| | 5600| 15
5700| 16| 5755| 14| | 5700| 15
5745| 16| 5795| 14| | 5745| 15
5825| 16|

MCS7_40

| 5190| 14| | 5825| 15

54Mbps

| 5180| 16| 5230| 14| |

MCS0_40

| 5190| 14
5240| 16| 5270| 14| | 5230| 14
5260| 16| 5510| 14| | 5270| 14
5320| 16| 5590| 14| | 5510| 14
5500| 16| 5670| 14| | 5590| 14
5600| 16| 5755| 14| | 5670| 14
5700| 16| 5795| 14| | 5755| 14
5745| 16|

802.11ac

|

MCS0_80

| 5210| 13| | 5795| 14
5825| 16| 5290| 13| |

MCS9_40

| 5190| 14

802.11n

|

MCS0_20

| 5180| 15| 5530| 13| | 5230| 14
5240| 15| 5690| 13| | 5270| 14
5260| 15| 5775| 13| | 5510| 14
5320| 15|

MCS9_80

| 5210| 13| | 5590| 14
5500| 15| 5290| 13| | 5670| 14
5600| 15| 5530| 13| | 5755| 14
5700| 15| 5690| 13| | 5795| 14
5745| 15| 5775| 13|
5825| 15|

MCS0_20

| 5180| 15

MCS7_20

| 5180| 15| 5240| 15
5240| 15| 5260| 15
5260| 15| 5320| 15
5320| 15| 5500| 15
5500| 15| 5600| 15
5600| 15| 5700| 15
5700| 15| 5745| 15
5745| 15| 5825| 15
5825| 15|

Above Set Power is based on Antenna Gain of 4.27dBi Maximum

IEEE Specifications

WiFi TX EVM follow the IEEE spec that as list in the table below:

The SOMAT39 module 2.4GHz WiFi Sensitivity as list in the table below:

The SOMAT39 module 5GHz WiFi Sensitivity as list in the table below:

BLUETOOTH Radio Characteristics

Basic Rate
Output Power^| Average Power| 7| 10| 13| dBm
Frequency Range| | 2400| …| 2483.5| MHz
Sensitivity (BER)| BER ≦0.1%| | -92| -70| dBm
Maximum Input Level| BER ≦0.1%| | | -20| dBm
EDR
Relative Power| π/4-DQPSK| -4| 0| 1.0| dBm
8DPSK| -4| 0| 1.0| dBm
EDR Sensitivity(BER)| π/4-DQPSK| …| -91| -70| dBm
BER ≦0.01%
8DPSK| …| -86| -70| dBm
BER ≦0.01%
EDR Maximum Input Level| π/4-DQPSK| …| …| -20| dBm
BER ≦0.01%
8DPSK| …| …| -20| dBm
BER ≦0.01%
BLE
BLE Output Power^| Average Power| -4| 2| 6| dBm
BLE Sensitivity (PER)| PER ≦30.8%| …| -95| -70| dBm
BLE Maximum Input Level| PER ≦30.8%| …| …| -10| dBm

The maximum output power is based on the Antenna Gain of 4.27 dBi.

RF Layout, Soldering Guidelines

RF Layout & Design Guidelines

1.  Do not run antenna cables directly above or directly below the radio.
2.  Do not run any high speed digital lines below the radio.
3.  For applications using only 1X1, the second antenna port i.e RF_ANT1 to be terminated with a 50 ohm resistor close to the pin of SOMAT39.
4.  Isolate VDD2 & VDD3 (pin no 36 & 37) with a ferrite bead (BLM15AG100SN1D) and decaps of 22uF and 0.1uF to be placed very close to the pins.
5. 10uF and 0.1uF to be used at VDD1 i.e pin no 23 and the input power supply which are to be placed very close to the pins.
6.  A 100K pull down resistors to be used for BT_DEV_WAKE, WL_EN and BT_EN close to the pins of RF SOM.
7.  A series R (10E) and shunt capacitor (22pf) is recommended to reduce the SDIO clock noise going to the input of SOMAT39 pin (pin no 43).
8.  Use proper electro-static-discharge (ESD) procedures when installing the SOMAT39 module.

Soldering Guidelines
SOMAT39 is compatible with industrial standard reflow profile for Pb-free solders. The reflow profile selection to be done based on the thermal mass of the entire populated PCB, heat transfer efficiency of the oven and solder paste used.

1. Refer to technical documentation of solder paste for profile configurations.
2. Avoid using more than one reflow cycle.
3. Aperture size of the stencil should be 1:1 with the pad size.
4. For further recommendations, please refer to the JEDEC/IPC J-STD-020, IPC-SM-782 and IPC 7351 guidelines.

Below is the overview of recommended Re-flow:

1. Solder paste alloy: SAC305 (Sn96.5/Ag3.0/Cu0.5) (Lead Free solder paste.)
2. A-B. Temp.: 150~200℃; soak time:60~120sec. (Base on Flux type, reference only)
3. C. Peak temp: <245℃
4. D. Time above 217 ℃: 40~90sec. (Base on SAC305)
5. Suggestion: Optimal cooling rate is <1℃/sec. from peak to 217 ℃.
6.  Nine heater zones at least for Reflow equipment.
7. Nitrogen usage is recommended and be controlled a value less than 1500 ppm. Note: Need to inspect solder joint by X-ray post reflow

Agency Approvals

FCC

Model: SOMAT39
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. However, there is no guarantee that interference will not occur in a installation. If this equipment does cause harmful interference to radio or reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that my cause undesired operation.

MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Industry Canada
Model: SOMAT39 IC: 1693B-HWUSIA
This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

MSL Level / Storage Conditions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>