ELATEC TWN4F17 TWN4 MultiTech M BLE Module User Manual
- June 6, 2024
- ELATEC
Table of Contents
ELATEC TWN4F17 TWN4 MultiTech M BLE Module
INTRODUCTION
ABOUT THIS MANUAL
This integration manual explains how to integrate ELATEC RFID module TWN4
MultiTech M into a host device and is mainly intended for integrators and host
manufacturers. The content of this integration manual is subject to changes
and printed versions might be obsolete. As the module manufacturer, ELATEC is
responsible for the update, release and publication on the FCC database of
this integration manual. The integrators and host manufacturers are required
to use the latest integration manual published by ELATEC on the FCC database.
ELATEC, integrators and host manufacturers are liable for any failure to
observe these requirements.
SAFETY NOTES
- ELATEC TWN4 MultiTech M is an electronic component and should be installed exclusively by a trained and qualified personnel.
- ELATEC recommends the integrators to follow general ESD protective measures during the installation of the TWN4 MultiTech M in a host device, e.g. the use of an antistatic wristband or special gloves.
- The integrator should not touch the antennas (if not shielded), printed circuit boards, connectors or other sensitive components on the TWN4 MultiTech M.
- Before installing the TWN4 MultiTech M in a host device, the integrator should also make sure that he/she has read and understood the technical documentation of the host manufacturer related to the host device.
TERMS AND DEFINITIONS
| Term | Definition |
|---|---|
| host device | Also “host” or “host product”. Device in which an RFID module is |
intended to be installed for operation.
integrator| Responsible party for the integration of an RFID module into a
host device. The integrator might be
the module manufacturer, the host manufacturer, the end user or any other third party.
modular type| Physical configuration in which a modular transmitter operates when installed within a host device. It can be a single-modular, a limited single-modular, a split-modular or a limited split-modular type.
RFID module
| Device intended to be used within another device or product. Depending on the equipment
configuration and intended use, an RFID module has to meet different requirements to get a modular grant.
ELATEC documentation
TWN4 MultiTech M data sheet TWN4 MultiTech M functional description TWN4
MultiTech M technical handbook TWN4 MultiTech M user manual
External documentation
| Document name | Document title/description | Source |
|---|---|---|
| n/a | Technical documentation related to the |
host product
| Host product manufacturer
784748 D01 General labeling and Notification| General Guidelines for Labeling
and Other Information Required to be
Provided to Users
| Federal Communications Commission Office of Engineering and Technology
Laboratory Division
996369 D01 Module Equip Auth Guide
| Transmitter Module Equipment Authorization Guide| Federal Communications Commission Office of Engineering and Technology
Laboratory Division
996369 D02 Module Q and A| Frequently Asked Questions and| Federal
Communications Commission
| Answers about Modules| Office of Engineering and Technology Laboratory
Division
---|---|---
996369 D03 OEM Manual
| Guidance for Modular Transmitter
Instruction Manuals and TCB Certification Application Reviews
| Federal Communications Commission
Office of Engineering and Technology Laboratory Division
996369 D04 Module Integration Guide
| Modular Transmitter Integration Guide—
Guidance for Host Product Manufacturers
| Federal Communications Commission
Office of Engineering and Technology Laboratory Division
For more information about this integration manual or the TWN4 MultiTech M, go to www.elatec.com or contact ELATEC.
ABOUT TWN4 MultiTech M
ELATEC’s TWN4 family of transponder readers and writers allows users to read and write to almost any 125 kHz, 134.2 kHz and 13.56 MHz tags and/or labels. It supports all major transponders from various suppliers like ATMEL, EM, ST, NXP, TI, HID, LEGIC, etc. and ISO standards like ISO14443A/B (T=CL), ISO15693, ISO18092 / ECMA-340 (NFC). The new generation is a direct enhancement to the successful TWN3 family as it comes in the same mechanical dimensions (OEM PCB and Desktop Housing). The reader supports host communication via USB or RS-232. Refer to product data sheet or elatec.com for technical data.
INTEGRATION IN OTHER DEVICES
TECHNICAL REQUIREMENTS
In order to start operating a TWN4 MultiTech M transponder reader, it simply
has to be connected to a host. Once the transponder reader is connected to the
host, it detects the type of communications cable (USB or RS232), with which
it is connected to the host.
Abbildung 1: Dimensions and pinout of TWN4 MultiTech M
MECHANICAL INSTALLATION
There are 4 holes for mechanical fixation of the board, see Abbildung 1:
Dimensions and pinout of TWN4 MultiTech M
ELECTRICAL CONNECTION
The module can be connected via USB, RS232 and other interfaces see Abbildung
1: Dimensions and pinout of TWN4 MultiTech M The input voltage is 4.3V to
5.5V.
FURTHER REQUIREMENTS
Label requirements
Using a permanently affixed label, the TWN4 MultiTech M must be labeled with an own FCC identification number. In case this label is not visible anymore after integration of the TWN4 MultiTech M in the host device, it is necessary to bring a label on the host device (on a visible and accessible place) stating the FCC identification number of the integrated TWN4 MultiTech M.
(RF module)
Compliance statement: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Modification of equipment:
The instruction manual of the host shall include the following statement:
Changes or modifications made to this equipment not expressly approved by the
party responsible for compliance may void the FCC authorization to operate
this equipment.
Information to the user: (The instruction manual of the host shall include the
following statement) A compliance statement as applicable, e.g., for devices
subject to part 15 of CFR 47 as specified in §15.19(a)(3), that the product
complies with the rules; and the identification, by name, address and
telephone number or Internet contact information, of the responsible party, as
defined in §2.909. The responsible party for Supplier’s Declaration of
Conformity must be located within the United States.
Host devices
FCC notes for a host subject to verification or SDoC: For a host device
assembled with the certified module and subject to 47 CFR Part 15 verification
of class A digital devices, the following statements have to be included in
the user manual and the host device has to be labelled as noted below. If the
host device is subject to other authorization procedures or parts the
appropriate requirements of these authorization procedures or parts apply.
Important note:
OEM integrator is still responsible for the FCC compliance requirements of the
end product, which integrates this module. Appropriate measurements (e.g. 15B
compliance) and if applicable additional equipment authorization of the host
device to be addressed by the integrator/ manufacturer The end device must be
labeled with: Contains FCC ID: WP5TWN4F17 Contains IC: 7948A-TWN4F17 HVIN:
EL20208
- Zeppelinstr. 1
- 82178 Puchheim
- Germany
- P +49 89 552 9961 0
- F +49 89 552 9961 129
- E-mail: info-rfid@elatec.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>