Sunco SHG-80W 4FT LED Grow Light User Manual

Sunco SHG-80W 4FT LED Grow Light

Dimensions:

• Width: 7.6 inches
• Length: 47.2 inches
• Height: 1.9 inches

Specifications

• Voltage: 80W
• Wattage: 80W
• Power Factor: Not specified
• Beam Angle: Not specified
• PPF: Not specified
• PAR: Not specified
• Dimmable: Not specified
• Average Lifetime: 50000 hours
• Full Spectrum: 380nm to 780nm
• Moisture Rating: Damp
• CRI: Not specified
• Usage Frequency: Indoor
• Warranty: 3 Years

Product Usage Instructions

Suspended Installation
Step 1:

1. Turn off the circuit breaker before installation.
2. The surface where the fixture will be installed must support its weight.
   • For plasterboard, a thickness of 3/8 inches is required.
   • Use #8 eye hook screws with anchors or expansion bolts (not included).

Step 2:

1. Drill pilot holes 46.5 inches apart.
2. Insert two plastic anchors, then screw each eye hook into an anchor.

Step 3:

1. Depending on your lighting plan, space any additional anchors accordingly.
   • Connect up to 4 shop lights together.

Step 4:

1. Insert a hook chain into each slot of the light fixture. Repeat for each slot (there should be 4 total).
2. Use pliers to crimp ends and secure as needed.

Step 5:

1. Hang the loose ends of the chain onto the Screw Eye hooks in the ceiling.

Step 6:

1. Plug the power cord into an electrical outlet.
2. Turn on the circuit breaker and test the light.
   • The distance between the lamp and the plant surface should be between 11.81 – and 23.62 inches.

Surface Mount
Step 1:

1. Turn off the circuit breaker before installation.
2. The surface where the fixture will be installed must support its weight.
   • For plasterboard, a thickness of 3/8 inches is required.
   • Use #8 eye hook screws with anchors or expansion bolts (not included).

Step 2:

1. Install 2 plastic anchors 3.25 inches apart, and two plastic anchors opposite to that one, 46 inches away from the other 2 plastic anchors. Insert a screw into each anchor.
2. The gap between the cap nut and the ceiling should be 0.33 inches.

Step 3:

1. Depending on your lighting plan, space any additional anchors accordingly.
   • Connect up to 4 shop lights together.

Step 4:

1. Lift the fixture up to screws and slide to one side to secure it into place. The fixture should be firmly fixed against the screws.

Step 5:

1. The distance between the lamp and the plant surface should be between 11.81 and 23.62 inches.

Step 6:

1. Plug the power cord into an electrical outlet.
2. Turn on the circuit breaker and test the light.

FAQ

• Q: What is the average lifetime of the LED grow light?
  A: The average lifetime is 50000 hours.

• Q: Can I use the LED grow light outdoors?
  A: No, the LED grow light has a moisture rating of Damp and is intended for indoor use only.

• Q: Is the LED grow light dimmable?
  A: The dimmability of the LED grow light is not specified.

**What’s in the Box?

**

Grow Light

Safety Information

To reduce the risk of fire, electric shock, or physical injury:

• Turn off the power before changing the fixture.
• Suitable for use in damp environments at temperatures ranging from 4°F to 113°F. Not for use where directly exposed to water.
• Not intended for use with emergency fixtures.
• Not compatible with photo controls.
• Not compatible with occupancy sensors.
• Not compatible with dimmers.
• Not compatible with timing devices.
• All electrical connections must be per local and National Electric Code (N.E.C.) standards.
• Please review the installation manual carefully before proceeding. Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
  WARNING:
  Cancer & Reproductive Harm- www.P65Warnings.ca.gov

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.

Suspended Installation

• STEP 1

  • a. Turn off the circuit breaker before installation.
  • b. Surface must support fixture weight.
    Plasterboard: Requires 3/8” thickness. Use #8 eye hook screws with anchors or expansion bolts (not included).

• STEP 2

  • a. Drill pilot holes 46.5 inches apart.
  • b. Insert two plastic anchors, then screw each eye hook into an anchor.

• STEP 3

  • a. Depending on your lighting plan, space any additional anchors accordingly.
  • b. Link up to 4 shop lights together

• STEP 4

  • a. Insert a hook chain into each slot of the light fixture. Repeat for each slot (there should be 4 total).
  • b. Use pliers to crimp ends and secure as needed.

• STEP 5

  • a. Hang the loose ends of the chain onto the Screw Eye hooks in the ceiling.

• STEP 6

  • a. Plug the power cord into an electrical outlet. Turn on the circuit breaker and test the light.
  • b. Distance between lamp and plant surface should be between 11.81 – 23.62 inches.

Surface Mount

• STEP 1

  • a. Turn off circuit breaker before installation.
  • b. Surface must support fixture weight.
    Plaster board: Requires 3/8” thickness. Use #8 eye hook screws with anchors or expansion bolts (not included).
    

• STEP 2

  • a. Install 2 plastic anchors 3.25 inches apart, and two plastic anchors opposite to that one, 46” inches away from the other 2 plastic anchors. Insert a screw into each anchor.
  • b. The gap between the cap nut and the ceiling should be 0.33 inches.

• STEP 3

  • a. Depending on your lighting plan, space any additional anchors accordingly.
  • b. Link up to 4 shop lights together

• STEP 4

  • a. Lift fixture up to the screws and slide to one side to secure it into place. The fixture should be firmly fixed against screws.

• STEP 5

  • a. Distance between lamp and plant surface should be between 11.81 and 23.62 inches.

• STEP 6

  • a. Plug the power cord into an electrical outlet.
  • b. Turn on the circuit breaker and test the light.

Product Details

Dimensions

Specifications

Light Distribution Angle

Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area. There are two main types of lighting distribution angles: A symmetric lighting distribution emits light evenly in all directions, creating a cone-shaped pattern that provides a pool of light. This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting. Symmetric lighting is also used to a certain degree in up-lighting. An asymmetric lighting distribution angle, also known as beam angle, creates a pattern that focuses light in a specific direction. This type of lighting is ideal for task lighting as it reduces glare and light spill in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums, and much more. It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.

Customer Support

Warranty Policy

• This product is covered by our industry leading 3 year warranty.
• It gets even better – scan the QR code for 2 extra years of protection!

30 Day Return Policy

• At Sunco, we value our customers and stand by the quality and performance of our products.
• If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.

Customer Service

Our Los Angeles team of lighting experts is here to assist you with all your needs! Contact us at: Email: support@sunco.com Call or Text: 844-334-9938

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>