H Koenig IM BOE40 Temperature Controlled Kettle Instruction Manual

: June 5, 2024
: H Koenig

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS
SAFETY
SPECIFICATIONS
SCHEMATIC CIRCUIT DIAGRAM
PART DESCRIPTION
FEATURES
USE
HOW TO CLEAN KETTLE
TROUBLESHOOTING
ENVIRONMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

boe40

Instruction Manual

Temperature controlled kettle
https://goo.gl/vu2j5r

IMPORTANT SAFETY INSTRUCTIONS

READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

Carefully read this manual before using this appliance. Ensure that you know how the appliance functions and how to operate it. Maintain the appliance in accordance with the instructions to ensure that it functions properly. Keep this manual with the appliance. If the appliance is to be used by a third party, this instruction manual must be supplied with it. The safety instructions do not by themselves eliminate any danger completely and proper accident prevention measures must always be used. No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling. Do not use this appliance if it has been dropped or damaged in any way, or if the supply cord is damaged.

SAFETY

Keep away from their kids or mentally handicapped people, or there are children when in use, please strictly supervise them by adults, besides, this product can not be played as a toy by the child.
Before connecting the power, please check whether the using voltage of the kettle is in line with the voltage marked on the kettle or not (rated voltage marked at the bottom of the kettle). If it is out of line, do not use it, and contact your local dealer.
During filling water, cleaning, or when not in use, turn off the kettle and unplug the plug.
When filling water, please keep the water away from the bottom of the enclosed, besides, before connecting the base, please wipe away beads of water below with a dry cloth to avoid a risk of electric shock or short circuit.
Loaded water should not exceed the maximum water level, or boiling water may spill and cause danger.
Please use this product in the horizontal plane.
The pensile power cord can cause an accident, it is recommended that when boiling water, in order to avoid tripping the kettle, then causing the danger of scalding, please put the kettle near to the power socket beside the wall.
To avoid burns, please make sure to confirm the kettle lid has been covered before use.
When heating, do not open the kettle lid or move the kettle or maybe burned.
In order to prevent electrical danger, please don’t let this product and power lines immersed in any liquid.
At a room with a temperature below 0 degrees Celsius, please do not let the kettle power supply have been connected to the power plug all the time, otherwise automatic temperature controller will automatically reset so that it leads to a heating element.
The power cord is damaged, in order to avoid danger, you must use the same model of power line replaced by the staff of the maintenance department from the manufactory.
Do not let the kettle drily combust, when not in use, make sure to cut off the power.
When cleaning this kettle, please remove the base, please wipe away the water on the kettle encloser and base before using it again.
The product must be used together with the base offered.
This product can only be used to heat water, not for other purposes, please do not add the soluble drinks, coffee, soup, milk, and other substances to water.
When boiling water, please do not open the kettle lid.
When pouring boiling water, please be very careful and slow, in order to prevent wounding of gushy water.
The power socket is used with a good three-core power socket grounded
When unplugging the Plug, please do not pull the power cord, please unplug the plug by hand.
When hands are wet, please do not operate this product.
Make sure to turn off the power switch before removing the base.
The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction
Children being supervised not to play with the appliance
If the kettle is overfilled, boiling water may be ejected
The instructions for the use of cordless kettles shall state that the kettle is only to be used with the stand provided
This appliance is intended to be used in household and similar applications as:
– Staff kitchen areas in shops, offices, and other working environments
– Farmhouses
– By clients in hotels, motels, and other residential type environments
– Bed and breakfast type environments
This device is not intended for use by persons with reduced capacity on the physical, mental or sensory or lack of experience and knowledge (including children), unless they have had instructions to use the appliance by a person responsible for their safe use of the appliance and understand the hazards involved. Children should be
supervised to ensure they do not play with the device.

SPECIFICATIONS

Rated Voltage/ Frequency: 220-240V / 50Hz
Rated Power: 1850-2200W
Rated Capacity: 1.7L

SCHEMATIC CIRCUIT DIAGRAM

PART DESCRIPTION

FEATURES

A high-quality temperature controller ensures 100% boiling, food-grade plastic material in accordance with national health standards.
With triple safety protection devices, the more precise the temperature controller, the safer use, and the longer life.
Wireless-type pot body design, 360-degree rotating base to avoid the right place, easy to use.
Concealed heating element design, high thermal efficiency, long service life, easy to clean.
High-polished stainless steel kettle body, lasting beautiful, noble and generous, healthy and durable.
Heating to boiling quickly after 5-8 minutes after filling with water.
know the water level at a glance from a water altitude scale.
The indicator light shows that the kettle shuts the power automatically after the water is boiling.
With elegant appearance, unique features, be the fine gift of a new friend, catering to the requirement of fast-speed life in the families and living rooms.

USE

Boiling water function

Open the lid and full water (not more than the maximum water level of 1. 8 L and cannot be less than the minimum water
level of 0. 8 L), then put on the lid.

Connected the power, and the pot body into the power base. Now nothing appears on the LCD, which means the kettle is on standby. When the kettle is on standby, only can use the ‘I/O’, you can use the ‘+’ and ‘-‘ buttons.

Method 1: firstly, press ‘+’ or ‘-‘, LCD shows 40℃. Press ‘+’ or ‘-‘ again, choose to set the temperature of the boiling water , and then press ‘I/O’, LCD flashing constantly means boiling water; I don’t press ‘I/O’, LCD will not flicker, after 10 seconds, LCD no display, the kettle back to standby.

Method 2: firstly press the’ + ‘or’ – ‘button and select the temperature of the boiling water (if only press ‘I/O’, by default water will be boiled up to 100℃.

LCD shows s ‘100’, LCD will keep flashing, into boiling water. When Setting the boiling water to 100 ℃, the water must be 100 ℃.

In the process of boiling water, press ‘+’ or ‘-‘, and you can reset the temperature. When a set temperature is higher than the actual water temperature, continue to boil water; When the actual water temperature is up to the set temperature, the heating tube will not work, and the electronic board starts the time, about 2 minutes later, the LED no display, which means the kettle back to standby.

When water is finished boiling, the heat pipe stop working, the electronic board starts timing, about 2 minutes later, the LCD no display, the kettle back to standby. If in 2 minutes, press the ‘I/O’ key, LCD no display, the kettle back to standby. If press the ‘+’ or ‘-‘ key, and don’t press ‘I/O’ again, the electronic board starts timing, about10 seconds later, LCD without any display. If press ‘+’ or ‘-’, and press ‘I/O’ again, the electronic board will reset the work.

Insulation functions

Open the lid and full water (not more than the maximum water level of 1. 8 L and cannot be less than the minimum water level of 0. 8 L), then put on the lid.

Connected the power, and the pot body into the power base. Now nothing appears on the LCD, which means the kettle is on standby. When the kettle is on standby, only can use the’I/O’, you can use the ‘+’ and ‘-‘ buttons.

The highest heat preservation temperature can only be set at 90 ℃: when the set temperature and actual water temperature is higher than 90 ℃, then pressing ‘ ‘button will not work; When’ ‘button has been pressed and set the water temperature as 90 ℃, and then press the ‘+’ button will not work.

Method 1: firstly, press ‘+’ or ‘-‘, LCD show 40℃, then press the ‘+’ or ‘-‘ button and set heat preservation temperature, press ‘ ‘ keep warm Button, and then press ‘I/O’ again, LCD and the sign under the LCD on right keep flashing.

The kettle is in the preservation and began to boil water. At this time, if not press ‘I/O’, LCD and the dot under the LCD on right will not flash, after 10 seconds, the LCD is not displayed, the kettle is back to standby.

Method 2: you can press ‘ ‘ and then press the ‘ + ‘or ‘ – ‘ button and set preservation temperature, and then push the ‘I/O’ heat preservation, LCD and the sign under the LCD on right keep flashing, The kettle is into the preservation and began to boil water.

In the process of boiling water, press ‘+’ or ‘-‘, which can reset the heat preservation temperature. When a set temperature is higher than the actual water temperature, continue to boil water; When the actual water temperature is up to the set temperature, the heating tube will not work, and the electronic board starts the time, about 4 hours later, LCD no display, which means the kettle back to standby. When, after LCD no display, the kettle back to standby mode.

When the boiling water temperature is up to the set temperature, the heat pipes stop working, and the kettle began to heat preservation.

When the water temperature is lower than the set temperature, heat pipes began to heat, and up to the setting temperature, and the LCD and the sign under the LCD on right keep flashing. When the water temperature is equal to or higher than the set temperature, the heat pipe does not work, in the insulation state, the LCD and the sign under the LCD on right will not flash and repeat.

In the process of heat preservation, if press the key to exit the heat preservation function, return to boil water.
When entered into the state of thermal insulation, electronic board start time, about 4 hours later, the LCD no display, then the kettle back to standby Within an hour, press ‘I/O’, LCD no display, the kettle back to standby.

HOW TO CLEAN KETTLE

Please unplug the power plug and let the pot become cool before cleaning.
Please do not immerse the kettle, power cord, power plug, and power socket into water.
Please ensure the electronic line circuit is dry.
Please wipe the kettle body with a damp cloth. Please do not use scouring powder, or cleaning ointment products, they will damage the surface characteristics of the kettle.

HOW TO ELIMINATE SCALE

In order to keep the good working condition of the kettle, it needs to remove scale frequently. If the outage happens in advance when working, indicate that you need to clear the scale of the kettle. Please use several methods in the following to clear the scale:

Please use a dedicated product that can remove the scale very well, and proceed in accordance with product instructions.
Please add the 0.5-liter eight-degree white vinegar to the pot, need costs one hour to keep soaking, then drain the white vinegar, and at last wash it 4-5 times with clean water.
Please add 0.5 liters of water to the pot and then boil it, then add 25 grams of citric acid, later soak 15 minutes, at last wash it 4-5 times with clean water.

TROUBLESHOOTING

Failure	Sources of failure and troubleshooting ways

it shuts down automatically
in advance before boiling|

1. It can be resolved by clearing the scale that is usually caused by the scale.
2. It also may be due to inadequate water in the kettle or empty kettle when using, causing to start dry combustion protection devices, we follow these steps to re-setting: again we add cold water to the pot, the dry burning protection device will be reset after about 2 minutes, then the kettle can work.

The kettle can not work| 1. Please check whether the connecting of the plug and socket is ok or not.
2. If the power cord is damaged, you must use the same type of power cord replaced by the staff of the maintenance department in the manufactory.
3. When the kettle starts dry combustion, the dry combustion protection device will shut the power.
There is a little peculiar smell inside the water| 1. This phenomenon usually happens when the kettle is used for the first time. To solve this trouble in accordance with Use Article 6.
2. If this problem persists, add water to the pot to the maximum position, add two soup spoons of saleratus to the water, and then drain the water after boiling.
It is dirty water or water scale inside the kettle|

As the local water is hard, this kind of water is caused by calcium carbonate and magnesium carbonate, just clear the scale in time.

ENVIRONMENT

CAUTION:

Do not dispose of this product as it has with other household products. There is a separation of this waste product into communities, you will need to inform your local authorities about the places where you can return this product. In fact, electrical and electronic products contain hazardous substances that have harmful effects on the environment or human health and should be recycled. The symbol here indicates that electrical and electronic equipment should be chosen carefully, a wheeled waste container is marked with a cross.

Adeva SAS / H.Koenig Europe
8 rue Marc Seguin, 77290 Mitry-Mory, France
www.hkoenig.com
https://en.hkoenig.com
Tél: +33 1 64 67 00 05